Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM
RM33C0E _58 Vehicle Interior _065458 METER / GAUGE / DISPLAY _0330016 METER / GAUGE SYSTEM C

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  B150013  Fuel Sender Circuit Open  


DESCRIPTION

This DTC is stored when the combination meter assembly detects a fuel sender gauge assembly malfunction via a direct line.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory Note
B150013 Fuel Sender Circuit Open Diagnosis Condition:
·

The power switch is on (IG)

·

IG power source voltage is 9.5 V or more


Malfunction Status:
·

Voltage signal from fuel sender gauge assembly is 0.2 V or less 3.0 times consecutively

·

Voltage signal from fuel sender gauge assembly is 4.7 V or more 3.0 times consecutively


·

Harness or connector

·

Fuel sender gauge assembly

·

Fuel suction tube with pump and gauge assembly

·

Combination meter assembly


DTC stored -

WIRING DIAGRAM

E367210E01
2.552,1.417 2.708,1.615 0.156,0.198 10 false 3 2.531,2.083 2.688,2.281 0.156,0.198 10 false 2 2.521,0.729 2.677,0.927 0.156,0.198 10 false 1 2.198,0.719 2.448,0.906 0.25,0.188 10 false FV 2.24,1.406 2.458,1.583 0.219,0.177 10 false FS 2.24,2.083 2.458,2.26 0.219,0.177 10 false FE 1.875,1.167 2.031,1.365 0.156,0.198 10 false 3 1.885,1.875 2.042,2.073 0.156,0.198 10 false 2 2.021,1.406 2.177,1.604 0.156,0.198 10 false 1 5.573,0.719 5.76,0.927 0.188,0.208 10 false 15 5.604,2.083 5.781,2.302 0.177,0.219 10 false 33 5.594,1.427 5.802,1.615 0.208,0.188 10 false 14 0.302,2.833 0.573,3.021 0.271,0.188 10 false R44 0.313,3.01 3.5,3.219 3.188,0.208 10 false Fuel Suction Tube with Pump and Gauge Assembly 0.719,1.375 1.479,1.917 0.76,0.542 10 false Fuel Sender Gauge Assembly 5.854,0.719 6.104,0.906 0.25,0.188 10 false FV 5.854,2.083 6.073,2.26 0.219,0.177 10 false FE 5.854,1.427 6.146,1.625 0.292,0.198 10 false FR 0.729,1.188 0.885,1.385 0.156,0.198 10 false A 5.198,3.177 7.094,3.375 1.896,0.198 10 false Combination Meter Assembly 5.219,2.969 5.5,3.177 0.281,0.208 10 false K21 6.385,1.521 6.604,1.698 0.219,0.177 10 false I/F 6.406,0.396 6.656,0.583 0.25,0.188 10 false 5 V

CAUTION / NOTICE / HINT

NOTICE:

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.


PROCEDURE

1.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Combination Meter > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Fuel Input Fuel input Min.: 0 L, Max.: 655.34 L or Unset
w/o Canister Pump Module
·

Fuel receiver gauge indicates F: 44.08 L

·

Fuel receiver gauge indicates 3/4: 37.50 L

·

Fuel receiver gauge indicates 1/2: 25.00 L

·

Fuel receiver gauge indicates 1/4: 12.50 L

·

Fuel receiver gauge indicates F: 5.00 L


w/ Canister Pump Module
·

Fuel receiver gauge indicates F: 44.37 L

·

Fuel receiver gauge indicates 3/4: 36.98 L

·

Fuel receiver gauge indicates 1/2: 24.65 L

·

Fuel receiver gauge indicates 1/4: 12.33 L

·

Fuel receiver gauge indicates F: 4.93 L


-
Body Electrical > Combination Meter > Data List
Tester Display
Fuel Input
50003 409 20

Result:
Result Proceed to
Fuel level data can be displayed on the GTS A
Fuel level data cannot be displayed on the GTS B



A

REPLACE COMBINATION METER ASSEMBLY

B

2.CHECK HARNESS AND CONNECTOR (FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY - COMBINATION METER ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Disconnect the R44 fuel suction tube with pump and gauge assembly connector.


b.

Disconnect the K21 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R44-1 (FV) - K21-15 (FV) Always Below 1 Ω
R44-3 (FS) - K21-14 (FR) Always Below 1 Ω
R44-2 (FE) - K21-33 (FE) Always Below 1 Ω
R44-1 (FV) or K21-15 (FV) - Body ground Always 10 kΩ or higher
R44-3 (FS) or K21-14 (FR) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT FUEL SENDER GAUGE ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT FUEL SENDER GAUGE ASSEMBLY

OK

4.INSPECT FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

NG

4.INSPECT FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY
E465544C01
0.333,1.333 0.75,1.583 0.417,0.25 0.333,3.667 0.75,3.917 0.417,0.25 2.083,1.271 2.344,0.917 true 1.719,1.229 1.719,0.75 true 1.354,1.26 1.021,0.906 true 0.125,0.188 1.563,0.354 1.438,0.167 10 false *a 0.417,1.375 0.75,1.625 0.333,0.25 10 false R44 0.479,3.698 0.813,3.948 0.333,0.25 10 false A 0.833,0.76 1.167,1.01 0.333,0.25 10 false FS 1.646,0.573 1.979,0.823 0.333,0.25 10 false FE 2.302,0.74 2.635,0.99 0.333,0.25 10 false FV
*a Component without harness connected
(Fuel Suction Tube with Pump and Gauge Assembly)


a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R44-1 (FV) - A-3 Always Below 1 Ω
R44-2 (FE) - A-2 Always Below 1 Ω
R44-3 (FS) - A-1 Always Below 1 Ω
R44-1 (FV) - R44-3 (FS)
or
A-3 - A-1
Always Below 1 Ω
R44-1(FV) - R44-2(FE)
or
A-3 - A-2
Always Below 1 Ω
R44-2(FE) - R44-3(FS)
or
A-2 - A-1
Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPLACE FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY