Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM › 2017.09–2019.02
RM33C0E _58 Vehicle Interior _065457 LIGHTING (INT) _0330219 LIGHTING SYSTEM J

LIGHTING (INT)  LIGHTING SYSTEM  ACC Signal Circuit  


DESCRIPTION

This circuit detects the power switch on (ACC) or off condition, and sends it to the main body ECU (multiplex network body ECU).

WIRING DIAGRAM

E380181E04
1.948,0.719 2.51,0.938 0.563,0.219 10 false DC/DC 0.094,0.521 1.583,0.823 1.49,0.302 10 false from Auxiliary Battery 0.146,1.115 1.969,1.667 1.823,0.552 10 false from Certification ECU (Smart Key ECU Assembly) 1.094,2.594 2.146,2.813 1.052,0.219 10 false *1: for LHD 1.094,2.938 2.146,3.156 1.052,0.219 10 false *2: for RHD 2.771,0.542 3.229,0.74 0.458,0.198 10 false 3G 3.219,0.552 3.677,0.75 0.458,0.198 10 false 3F 3.25,0.344 3.708,0.542 0.458,0.198 10 false 1 2.833,0.344 3.292,0.542 0.458,0.198 10 false 1 2.792,0.75 3.073,0.99 0.281,0.24 10 false *2 3.208,0.75 3.49,0.99 0.281,0.24 10 false *1 3.229,1.167 3.688,1.365 0.458,0.198 10 false 3A 3.24,0.969 3.698,1.167 0.458,0.198 10 false 30 3.229,1.781 3.688,1.979 0.458,0.198 10 false 3B 3.271,1.583 3.729,1.781 0.458,0.198 10 false 3 5.885,2.615 6.344,2.813 0.458,0.198 10 false K51 4.219,1.448 5.01,1.656 0.792,0.208 10 false ACC 5.906,2.427 6.365,2.625 0.458,0.198 10 false 19 5.885,1.781 6.344,1.979 0.458,0.198 10 false MB 5.896,1.583 6.354,1.781 0.458,0.198 10 false 11 5.896,0.542 6.354,0.74 0.458,0.198 10 false MB 5.906,0.365 6.365,0.563 0.458,0.198 10 false 30 4.896,0.719 5.938,1.031 1.042,0.313 10 false ECU-ACC 6.292,0.427 6.75,0.625 0.458,0.198 10 false ACC 6.313,1.781 6.771,1.979 0.458,0.198 10 false GND1 6.313,2.615 6.771,2.813 0.458,0.198 10 false GND2 3.156,2.198 5.958,2.438 2.802,0.24 10 false Instrument Panel Junction Block Assembly 5.385,3.052 7.021,3.417 1.635,0.365 10 false Main Body ECU (Multiplex Network Body ECU)

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

First, check for smart entry and start system (for Start Function) DTCs, and after confirming that there is no malfunction, proceed with troubleshooting.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Start Function)>DTC CHECK / CLEAR

·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.



PROCEDURE

1.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
ACC SW Power switch on (ACC) signal OFF or ON OFF: Power switch off
ON: Power switch on (ACC)
"ON" is also displayed for this item when the power switch is on (IG).
Body Electrical > Main Body > Data List
Tester Display
ACC SW
50003 123 31
OK:

Normal conditions listed above are displayed.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Disconnect the 3F*1 or 3G*2 and 3B instrument panel junction block assembly connectors.


b.

Disconnect the K51 main body ECU (multiplex network body ECU) connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3F-1 - Body ground*1 Power switch off 11 to 14 V
3G-1 - Body ground*2 Power switch off 11 to 14 V


*1: for LHD

*2: for RHD



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3B-3 - Body ground Always Below 1 Ω
K51-19 (GND2) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
E333577C23
1.698,0.51 2.042,0.729 0.344,0.219 4.938,0.531 5.281,0.75 0.344,0.219 2.438,2.438 2.781,2.656 0.344,0.219 5.729,2.104 6.073,2.323 0.344,0.219 5.729,2.385 6.073,2.604 0.344,0.219 4.01,3.094 4.188,3.375 false 0.25,0.167 0.563,0.323 0.313,0.156 10 false *a 1.781,0.531 2.198,0.771 0.417,0.24 10 false 3B 5.021,0.542 5.438,0.781 0.417,0.24 10 false 3A 2.5,2.448 2.917,2.688 0.417,0.24 10 false MB 5.813,2.115 6.229,2.354 0.417,0.24 10 false 3F 4.083,3.406 4.5,3.646 0.417,0.24 10 false ACC 5.813,2.396 6.229,2.635 0.417,0.24 10 false 3G 6.125,2.146 6.542,2.385 0.417,0.24 10 false *A 6.125,2.406 6.542,2.646 0.417,0.24 10 false *B
*A for LHD *B for RHD
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
3F-1 - MB-30 (ACC) Auxiliary battery not connected to 3A-30 and 3B-3 10 kΩ or higher
3F-1 - MB-30 (ACC) Auxiliary battery positive (+) → 3A-30
Auxiliary battery negative (-) → 3B-3
Below 1 Ω


for RHD
Tester Connection Condition Specified Condition
3G-1 - MB-30 (ACC) Auxiliary battery not connected to 3A-30 and 3B-3 10 kΩ or higher
3G-1 - MB-30 (ACC) Auxiliary battery positive (+) → 3A-30
Auxiliary battery negative (-) → 3B-3
Below 1 Ω


Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY