Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM
RM33C0E _58 Vehicle Interior _065457 LIGHTING (INT) _0330219 LIGHTING SYSTEM J

LIGHTING (INT)  LIGHTING SYSTEM  Interior Light Auto Cut Circuit  


DESCRIPTION

The main body ECU (multiplex network body ECU) controls operation of the DOME CUT relay in order to supply power to the interior lights. When the battery saving function operates while the interior lights are on, the main body ECU (multiplex network body ECU) opens the DOME CUT relay to turn off the lights.

WIRING DIAGRAM

E380183E02
1.146,0.208 2.677,0.448 1.531,0.24 10 false from Auxiliary Battery 1.115,0.896 1.781,1.167 0.667,0.271 10 false DC/DC 2.177,0.708 2.531,0.958 0.354,0.25 10 false 3G 2.583,0.708 2.938,0.958 0.354,0.25 10 false 3F 2.219,0.51 2.573,0.76 0.354,0.25 10 false 1 2.604,0.51 2.958,0.76 0.354,0.25 10 false 1 2.594,0.927 2.948,1.177 0.354,0.25 10 false *1 2.188,0.927 2.542,1.177 0.354,0.25 10 false *2 3.24,0.875 3.771,1.135 0.531,0.26 10 false DOME 4.219,1.354 5.125,1.635 0.906,0.281 10 false DOME CUT 5.479,0.708 5.833,0.958 0.354,0.25 10 false MB 5.5,0.521 5.854,0.771 0.354,0.25 10 false 23 5.854,0.594 6.385,0.854 0.531,0.26 10 false DOMR 0.406,1.99 1.948,2.25 1.542,0.26 10 false to Each Interior Light 2.573,1.688 2.927,1.938 0.354,0.25 10 false 3D 2.573,2.302 2.927,2.552 0.354,0.25 10 false 3B 2.885,2.677 5.646,2.948 2.76,0.271 10 false Instrument Panel Junction Block Assembly 5.385,3.052 7.052,3.438 1.667,0.385 10 false Main Body ECU (Multiplex Network Body ECU) 2.573,1.479 2.927,1.729 0.354,0.25 10 false 19 2.573,2.094 2.927,2.344 0.354,0.25 10 false 10 0.917,2.958 2.604,3.156 1.688,0.198 10 false *1: for LHD 0.917,3.271 2.604,3.469 1.688,0.198 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.



PROCEDURE

1.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Relay for Interior Light Auto Cut Function DOME CUT relay OFF or ON When performing this Active Test, turn all the interior lights on.
·

OFF: DOME CUT relay on (interior lights turn on)

·

ON: DOME CUT relay off (interior lights turn off)


Body Electrical > Main Body > Active Test
Tester Display
Relay for Interior Light Auto Cut Function
50004 123 66
OK:

All of the interior lights turn off when ON is selected.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (POWER SOURCE - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the 3F*1 or 3G*2 instrument panel junction block assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3F-1 - Body ground*1 Power switch off 11 to 14 V
3G-1 - Body ground*2 Power switch off 11 to 14 V


*1: for LHD

*2: for RHD



Result:
Proceed to
OK
NG



OK

3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
E333583C10
1.958,0.677 2.292,0.906 0.333,0.229 5.177,0.646 5.51,0.885 0.333,0.24 2.333,2.531 2.677,2.75 0.344,0.219 5.74,2.115 6.073,2.333 0.333,0.219 5.75,2.417 6.083,2.635 0.333,0.219 3.552,3.427 3.271,3.094 false 0.208,0.24 0.521,0.396 0.313,0.156 10 false *a 2.042,0.698 2.49,1.031 0.448,0.333 10 false 3D 5.25,0.688 5.698,1.021 0.448,0.333 10 false 3B 2.406,2.552 2.854,2.885 0.448,0.333 10 false MB 5.833,2.125 6.281,2.458 0.448,0.333 10 false 3F 3.635,3.406 4.198,3.708 0.563,0.302 10 false DOMR 5.823,2.427 6.271,2.76 0.448,0.333 10 false 3G 6.135,2.427 6.583,2.76 0.448,0.333 10 false *B 6.135,2.135 6.583,2.469 0.448,0.333 10 false *A
*A for LHD *B for RHD
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD
Tester Connection Condition Specified Condition
3D-19 - Auxiliary battery negative (-) Auxiliary battery positive (+) → 3F-1
Auxiliary battery negative (-) → MB-23 (DOMR)
11 to 14 V
3B-10 - Auxiliary battery negative (-) Auxiliary battery positive (+) → 3F-1
Auxiliary battery negative (-) → MB-23 (DOMR)
11 to 14 V

for RHD
Tester Connection Condition Specified Condition
3D-19 - Auxiliary battery negative (-) Auxiliary battery positive (+) → 3G-1
Auxiliary battery negative (-) → MB-23 (DOMR)
11 to 14 V
3B-10 - Auxiliary battery negative (-) Auxiliary battery positive (+) → 3G-1
Auxiliary battery negative (-) → MB-23 (DOMR)
11 to 14 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
3F-1 - 3D-19 Always 10 kΩ or higher
3F-1 - 3B-10 Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
3G-1 - 3D-19 Always 10 kΩ or higher
3G-1 - 3B-10 Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY