Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM
RM33C0E _58 Vehicle Interior _065457 LIGHTING (INT) _0330219 LIGHTING SYSTEM J

LIGHTING (INT)  LIGHTING SYSTEM  Luggage Compartment Door Courtesy Switch Circuit  


DESCRIPTION

The main body ECU (multiplex network body ECU) receives a luggage compartment door open/closed signal from luggage compartment door courtesy light switch (luggage compartment door lock assembly).

WIRING DIAGRAM

E344236E10
1.646,0.792 2.302,1.125 0.656,0.333 10 false 2 1.854,0.792 2.51,1.125 0.656,0.333 10 false E 2.688,0.792 3.344,1.125 0.656,0.333 10 false D+ 2.969,0.792 3.625,1.125 0.656,0.333 10 false 3 1.042,1.188 1.698,1.521 0.656,0.333 10 false W3 1.052,1.333 4.146,1.938 3.094,0.604 10 false Luggage Compartment Door Courtesy Light Switch (Luggage Compartment Door Lock Assembly) 4.177,0.885 4.833,1.219 0.656,0.333 10 false 3D 4.188,0.688 4.844,1.021 0.656,0.333 10 false 34 4.365,1.479 5.969,1.917 1.604,0.438 10 false Instrument Panel Junction Block Assembly 5.688,0.896 6.344,1.229 0.656,0.333 10 false MB 5.729,0.698 6.385,1.031 0.656,0.333 10 false 4 6.073,0.896 6.729,1.229 0.656,0.333 10 false LGCY 5.365,2.042 7.021,2.708 1.656,0.667 10 false Main Body ECU (Multiplex Network Body ECU)

CAUTION / NOTICE / HINT

NOTICE:

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.


PROCEDURE

1.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Luggage Courtesy SW Luggage compartment door courtesy switch signal OFF or ON OFF: Luggage compartment door closed
ON: Luggage compartment door open
-
Body Electrical > Main Body > Data List
Tester Display
Luggage Courtesy SW
50003 123 53
OK:

Normal conditions listed above are displayed.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT LUGGAGE COMPARTMENT DOOR COURTESY LIGHT SWITCH (LUGGAGE COMPARTMENT DOOR LOCK ASSEMBLY)
2.INSPECT LUGGAGE COMPARTMENT DOOR COURTESY LIGHT SWITCH (LUGGAGE COMPARTMENT DOOR LOCK ASSEMBLY)
a.

Remove the luggage compartment door courtesy light switch (luggage compartment door lock assembly).

Click hereVehicle Interior>LIGHTING (INT)>BACK DOOR COURTESY SWITCH>REMOVAL


b.

Inspect the luggage compartment door courtesy light switch (luggage compartment door lock assembly).

Click hereVehicle Interior>LIGHTING (INT)>BACK DOOR COURTESY SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (LUGGAGE COMPARTMENT DOOR LOCK ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND BODY GROUND)

NG

REPLACE LUGGAGE COMPARTMENT DOOR COURTESY LIGHT SWITCH (LUGGAGE COMPARTMENT DOOR LOCK ASSEMBLY)

3.CHECK HARNESS AND CONNECTOR (LUGGAGE COMPARTMENT DOOR LOCK ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND BODY GROUND)
a.

Disconnect the 3D instrument panel junction block assembly connector.


b.

Measure the resistance according to the value (s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
W3-3 (D+) - 3D-34 Always Below 1 Ω
W3-3 (D+) or 3D-34 - Body ground Always 10 kΩ or higher
W3-2 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
E173023C41
1.208,0.271 1.583,0.5 0.375,0.229 4.635,0.271 5.01,0.5 0.375,0.229 3.385,1.052 3.25,1.469 false 0.26,0.104 0.5,0.302 0.24,0.198 10 false *a 2.844,1.479 3.281,1.656 0.438,0.177 10 false LGCY 1.313,0.292 1.646,0.458 0.333,0.167 10 false 3D 4.719,0.292 5.052,0.458 0.333,0.167 10 false MB
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3D-34 - MB-4 (LGCY) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY