INSPECT ILLUMINATED ENTRY SYSTEM OPERATION
Perform this inspection with the customize parameters at the initial settings.
Perform this inspection with the door linked switch of the map light (roof console box sub-assembly) on.
| Control | Condition | Lights that Operate |
|---|---|---|
| Actuation Area-linked | With the power switch off and all of the doors closed and locked, enter an exterior detection area while carrying an electrical key transmitter and check that the lights that operate turn on for approximately 15 seconds and then turn off. | ·
Map Light (Roof Console Box Sub-assembly) ·
Spot Light Assembly ·
Footwell Light (No. 1 Interior Illumination Light Assembly) ·
Front Door Inside Handle Illumination Light (No. 1 Interior Illumination Light Assembly) ·
Rear Door Inside Handle Illumination Light (No. 2 Interior Illumination Light Assembly)*1 ·
Instrument Panel Ambient Illumination Light (Instrument Panel Light Assembly)*2 |
| Door Lock/Unlock-linked | With the power switch off and all of the doors closed and locked, unlock any door using an unlock operation (key-linked, wireless or entry unlock operation) and check that the lights that operate turn on for 15 seconds and then turn off. | ·
Map Light (Roof Console Box Sub-assembly) ·
Spot Light Assembly ·
Footwell Light (No. 1 Interior Illumination Light Assembly) ·
Front Door Inside Handle Illumination Light (No. 1 Interior Illumination Light Assembly) ·
Rear Door Inside Handle Illumination Light (No. 2 Interior Illumination Light Assembly)*1 ·
Instrument Panel Ambient Illumination Light (Instrument Panel Light Assembly)*2 |
| Door Open/Close-linked | With the power switch off and all of the doors closed, open any door and check that the lights that operate turn on. While the lights that operate are on, close all of the doors and check that the lights that operate turn off after approximately 15 seconds. | ·
Map Light (Roof Console Box Sub-assembly) ·
Spot Light Assembly ·
Footwell Light (No. 1 Interior Illumination Light Assembly) ·
Front Door Inside Handle Illumination Light (No. 1 Interior Illumination Light Assembly) ·
Rear Door Inside Handle Illumination Light (No. 2 Interior Illumination Light Assembly)*1 ·
Instrument Panel Ambient Illumination Light (Instrument Panel Light Assembly)*2 |
| With the power switch off and all of the doors closed, open any door and check that the light that operates turns on. While the light that operates is on, close all of the doors and check that the light that operates turns off after approximately 40 seconds. | Power Switch Illumination | |
| With the power switch on (IG), open any door and check that the lights that operate turn on. While the lights that operate are on, close all of the doors and check that the lights that operate turn off. | ·
Map Light (Roof Console Box Sub-assembly) ·
Spot Light Assembly |
|
| Power Switch-linked | Turn the power switch from on (ACC) or on (IG) to off and check that the lights that operate turn on for approximately 15 seconds and then turn off. | ·
Map Light (Roof Console Box Sub-assembly) ·
Spot Light Assembly ·
Footwell Light (No. 1 Interior Illumination Light Assembly) ·
Front Door Inside Handle Illumination Light (No. 1 Interior Illumination Light Assembly) ·
Rear Door Inside Handle Illumination Light (No. 2 Interior Illumination Light Assembly)*1 ·
Instrument Panel Ambient Illumination Light (Instrument Panel Light Assembly)*2 |
| Turn the power switch from on (ACC) or on (IG) to off and check that the light that operates turns on for approximately 40 seconds and then turns off. | Power Switch Illumination | |
| Shift Position-linked | With the power switch on (ACC) or on (IG), move the shift lever from P to any other position and check that the lights that operate dim. While the lights that operate are on, move the shift lever to P and check that the lights that operate return to full brightness. | ·
Footwell Light (No. 1 Interior Illumination Light Assembly) ·
Front Door Inside Handle Illumination Light (No. 1 Interior Illumination Light Assembly) ·
Rear Door Inside Handle Illumination Light (No. 2 Interior Illumination Light Assembly)*1 ·
Instrument Panel Ambient Illumination Light (Instrument Panel Light Assembly)*2 |
*1: w/ Rear Door Inside Handle Illumination Light
*2: w/ Instrument Panel Ambient Illumination Light
INSPECT BATTERY SAVING CONTROL OPERATION
The operations and conditions of this control are described below.
| Control | Condition | Lights that Operate |
|---|---|---|
| Basic operation | When 20 minutes elapse after the power switch is turned from on (ACC) or on (IG) to off and the lights that operate remain on, the lights are turned off.
|
·
Power Switch Illumination ·
Map Light (Roof Console Box Sub-assembly) ·
Spot Light Assembly ·
Footwell Light (No. 1 Interior Illumination Light Assembly) ·
Front Door Inside Handle Illumination Light (No. 1 Interior Illumination Light Assembly) ·
Rear Door Inside Handle Illumination Light (No. 2 Interior Illumination Light Assembly)*1 ·
Instrument Panel Ambient Illumination Light (Instrument Panel Light Assembly)*2 |
| Interior light auto cut operation | When 20 minutes elapse after the power switch is turned from on (ACC) or on (IG) to off and the lights that operate remain on, the lights are turned off.
|
·
Map Light (Roof Console Box Sub-assembly) ·
Spot Light Assembly ·
Vanity Light Assembly ·
No. 1 Luggage Compartment Light Assembly ·
Courtesy Light Assembly |
*1: w/ Rear Door Inside Handle Illumination Light
*2: w/ Instrument Panel Ambient Illumination Light