Home › Vehicle Exterior › LIGHTING (EXT) › HEADLIGHT ASSEMBLY (for LED Type Turn Signal Light) › 2017.09–2019.10
RM33C0E _59 Vehicle Exterior _065472 LIGHTING (EXT) _0330491 HEADLIGHT ASSEMBLY G

LIGHTING (EXT)  HEADLIGHT ASSEMBLY  INSPECTION  


PROCEDURE

Hide 81175 1.INSPECT HEADLIGHT UNIT ASSEMBLY LH

E371635C04
1.094,5.177 1.438,5.417 0.344,0.24 2.771,5.292 3.115,5.531 0.344,0.24 4.229,5.302 4.573,5.542 0.344,0.24 5.917,5.313 6.26,5.552 0.344,0.24 1.438,6.313 1.542,5.698 true 1.563,6.292 1.906,5.802 true 1.802,6.969 1.458,6.448 true 1.104,6.302 0.521,5.896 true 1.229,6.281 0.802,5.677 true 1.813,6.292 2.073,6.125 true 0.771,6.281 0.292,6.063 true 1.333,6.281 1.25,5.604 true 1.063,7.083 1.229,6.427 true 0.802,6.99 1.094,6.427 true 2.031,6.729 1.781,6.448 true 0.406,6.688 0.781,6.458 true 1.469,7.104 1.333,6.427 true 0.521,6.844 0.99,6.448 true 1.677,6.281 2.021,5.938 true 0.542,0.573 0.854,0.771 0.313,0.198 10 false *1 4.042,2.031 4.354,2.229 0.313,0.198 10 false *a 0.365,2 0.677,2.198 0.313,0.198 10 false *b 5.073,0.771 5.385,0.969 0.313,0.198 10 false *c 6.427,3.26 6.74,3.458 0.313,0.198 10 false *d 0.385,5.323 0.698,5.521 0.313,0.198 10 false *a 2.313,5.354 2.625,5.552 0.313,0.198 10 false *b 3.813,5.354 4.125,5.552 0.313,0.198 10 false *c 5.333,5.396 5.646,5.594 0.313,0.198 10 false *d 1.219,5.219 1.531,5.417 0.313,0.198 10 false B 2.906,5.344 3.219,5.542 0.313,0.198 10 false C 4.365,5.344 4.677,5.542 0.313,0.198 10 false D 6.042,5.375 6.354,5.573 0.313,0.198 10 false E 1.5,5.521 2.271,5.719 0.771,0.198 10 false ACTBI 1.917,5.625 2.688,5.823 0.771,0.198 10 false ACTSI 1.792,6.99 2.563,7.188 0.771,0.198 10 false ACTGI 0.063,5.677 0.833,5.875 0.771,0.198 10 false LOLED2 0.458,5.5 1.229,5.698 0.771,0.198 10 false LOLED1 2.135,6.031 2.906,6.229 0.771,0.198 10 false HI+ 0.073,5.906 0.844,6.104 0.771,0.198 10 false HI- 1.042,5.448 1.813,5.646 0.771,0.198 10 false FANB 0.875,7.135 1.646,7.333 0.771,0.198 10 false FANP 0.479,7.031 1.25,7.229 0.771,0.198 10 false FANG 2.042,6.74 2.813,6.938 0.771,0.198 10 false DRL+ 0.052,6.646 0.823,6.844 0.771,0.198 10 false DRL- 1.375,7.135 2.146,7.333 0.771,0.198 10 false PWM1 0.115,6.854 0.885,7.052 0.771,0.198 10 false TURN- 2.063,5.833 2.833,6.031 0.771,0.198 10 false TURN+
*1 Headlight Unit Assembly LH (Headlight Cord) - -
*a Component without harness connected
(to Headlight ECU Sub-assembly LH)
*b Component without harness connected
(to Headlight Unit LH)
*c Component without harness connected
(to Headlight Leveling Motor LH)
*d Component without harness connected
(to Headlight Lens LH)


a.

Measure the resistance according to the value(s) in the table below.

i.

Inspect the headlight leveling motor circuit.

Standard Resistance:
Tester Connection Condition Specified Condition
B-7 (ACTBI) - D-1 Always Below 1 Ω
B-8 (ACTSI) - D-2 Always Below 1 Ω
B-17 (ACTGI) - D-3 Always Below 1 Ω


If the result is not as specified, replace the headlight unit assembly LH (headlight cord).


ii.

Inspect the Lo/Hi beam circuit.

Standard Resistance:
Tester Connection Condition Specified Condition
B-4 (LOLED2) - C-5 Always Below 1 Ω
B-5 (LOLED1) - C-6 Always Below 1 Ω


If the result is not as specified, replace the headlight unit assembly LH (headlight cord).


iii.

Inspect the Lo/Hi beam shade circuit.

Standard Resistance:
Tester Connection Condition Specified Condition
B-10 (HI+) - C-10 Always Below 1 Ω
B-1 (HI-) - C-4 Always Below 1 Ω


If the result is not as specified, replace the headlight unit assembly LH (headlight cord).


iv.

Inspect the headlight fan circuit.

Standard Resistance:
Tester Connection Condition Specified Condition
B-6 (FANB) - C-12 Always Below 1 Ω
B-15 (FANP) - C-11 Always Below 1 Ω
B-14 (FANG) - C-4 Always Below 1 Ω


If the result is not as specified, replace the headlight unit assembly LH (headlight cord).


v.

Inspect the clearance light/daytime running light circuit.

Standard Resistance:
Tester Connection Condition Specified Condition
B-20 (DRL+) - E-7 Always Below 1 Ω
B-11 (DRL-) - E-8 Always Below 1 Ω
B-16 (PWM1) - E-6 Always Below 1 Ω


If the result is not as specified, replace the headlight unit assembly LH (headlight cord).


vi.

Inspect the turn signal light circuit.

Standard Resistance:
Tester Connection Condition Specified Condition
B-9 (TURN+) - E-4 Always Below 1 Ω
B-13 (TURN-) - E-2 Always Below 1 Ω


If the result is not as specified, replace the headlight unit assembly LH (headlight cord).



Hide 81171A 2.INSPECT HEADLIGHT UNIT LH

E371636C02
0.448,0.583 0.76,0.781 0.313,0.198 10 false *a
*a Component without harness connected
(Headlight Unit LH)


a.

Apply auxiliary battery voltage to the headlight unit LH and check that the Lo/Hi beam shade operates.

OK:
Condition Specified Condition
Auxiliary battery positive (+) → Terminal 10
Auxiliary battery negative (-) → Terminal 4
Operates normally


If the result is not as specified, replace the headlight unit LH.


Hide 81171B 3.INSPECT HEADLIGHT LENS LH

E371637C02
0.458,0.969 0.771,1.167 0.313,0.198 10 false *a
*a Component without harness connected
(Headlight Lens LH)


a.

Apply auxiliary battery voltage to the headlight lens LH and check that the light illuminates.

OK:
Condition Specified Condition
Auxiliary battery positive (+) → Terminal 4
Auxiliary battery negative (-) → Terminal 2
Clearance light/daytime running light illuminates


If the result is not as specified, replace the headlight lens LH.


Hide 81135 4.INSPECT HEADLIGHT UNIT ASSEMBLY RH

E371635C04
1.094,5.177 1.438,5.417 0.344,0.24 2.771,5.292 3.115,5.531 0.344,0.24 4.229,5.302 4.573,5.542 0.344,0.24 5.917,5.313 6.26,5.552 0.344,0.24 1.438,6.313 1.542,5.698 true 1.563,6.292 1.906,5.802 true 1.802,6.969 1.458,6.448 true 1.104,6.302 0.521,5.896 true 1.229,6.281 0.802,5.677 true 1.813,6.292 2.073,6.125 true 0.771,6.281 0.292,6.063 true 1.333,6.281 1.25,5.604 true 1.063,7.083 1.229,6.427 true 0.802,6.99 1.094,6.427 true 2.031,6.729 1.781,6.448 true 0.406,6.688 0.781,6.458 true 1.469,7.104 1.333,6.427 true 0.521,6.844 0.99,6.448 true 1.677,6.281 2.021,5.938 true 0.542,0.573 0.854,0.771 0.313,0.198 10 false *1 4.042,2.031 4.354,2.229 0.313,0.198 10 false *a 0.365,2 0.677,2.198 0.313,0.198 10 false *b 5.073,0.771 5.385,0.969 0.313,0.198 10 false *c 6.427,3.26 6.74,3.458 0.313,0.198 10 false *d 0.385,5.323 0.698,5.521 0.313,0.198 10 false *a 2.313,5.354 2.625,5.552 0.313,0.198 10 false *b 3.813,5.354 4.125,5.552 0.313,0.198 10 false *c 5.333,5.396 5.646,5.594 0.313,0.198 10 false *d 1.219,5.219 1.531,5.417 0.313,0.198 10 false B 2.906,5.344 3.219,5.542 0.313,0.198 10 false C 4.365,5.344 4.677,5.542 0.313,0.198 10 false D 6.042,5.375 6.354,5.573 0.313,0.198 10 false E 1.5,5.521 2.271,5.719 0.771,0.198 10 false ACTBI 1.917,5.625 2.688,5.823 0.771,0.198 10 false ACTSI 1.792,6.99 2.563,7.188 0.771,0.198 10 false ACTGI 0.063,5.677 0.833,5.875 0.771,0.198 10 false LOLED2 0.458,5.5 1.229,5.698 0.771,0.198 10 false LOLED1 2.135,6.031 2.906,6.229 0.771,0.198 10 false HI+ 0.073,5.906 0.844,6.104 0.771,0.198 10 false HI- 1.042,5.448 1.813,5.646 0.771,0.198 10 false FANB 0.875,7.135 1.646,7.333 0.771,0.198 10 false FANP 0.479,7.031 1.25,7.229 0.771,0.198 10 false FANG 2.042,6.74 2.813,6.938 0.771,0.198 10 false DRL+ 0.052,6.646 0.823,6.844 0.771,0.198 10 false DRL- 1.375,7.135 2.146,7.333 0.771,0.198 10 false PWM1 0.115,6.854 0.885,7.052 0.771,0.198 10 false TURN- 2.063,5.833 2.833,6.031 0.771,0.198 10 false TURN+
*1 Headlight Unit Assembly RH (Headlight Cord) - -
*a Component without harness connected
(to Headlight ECU Sub-assembly RH)
*b Component without harness connected
(to Headlight Unit RH)
*c Component without harness connected
(to Headlight Leveling Motor RH)
*d Component without harness connected
(to Headlight Lens RH)


a.

Measure the resistance according to the value(s) in the table below.

i.

Inspect the headlight leveling motor circuit.

Standard Resistance:
Tester Connection Condition Specified Condition
B-7 (ACTBI) - D-1 Always Below 1 Ω
B-8 (ACTSI) - D-2 Always Below 1 Ω
B-17 (ACTGI) - D-3 Always Below 1 Ω


If the result is not as specified, replace the headlight unit assembly RH (headlight cord).


ii.

Inspect the Lo/Hi beam circuit.

Standard Resistance:
Tester Connection Condition Specified Condition
B-4 (LOLED2) - C-5 Always Below 1 Ω
B-5 (LOLED1) - C-6 Always Below 1 Ω


If the result is not as specified, replace the headlight unit assembly RH (headlight cord).


iii.

Inspect the Lo/Hi beam shade circuit.

Standard Resistance:
Tester Connection Condition Specified Condition
B-10 (HI+) - C-10 Always Below 1 Ω
B-1 (HI-) - C-4 Always Below 1 Ω


If the result is not as specified, replace the headlight unit assembly RH (headlight cord).


iv.

Inspect the headlight fan circuit.

Standard Resistance:
Tester Connection Condition Specified Condition
B-6 (FANB) - C-12 Always Below 1 Ω
B-15 (FANP) - C-11 Always Below 1 Ω
B-14 (FANG) - C-4 Always Below 1 Ω


If the result is not as specified, replace the headlight unit assembly RH (headlight cord).


v.

Inspect the clearance light/daytime running light circuit.

Standard Resistance:
Tester Connection Condition Specified Condition
B-20 (DRL+) - E-7 Always Below 1 Ω
B-11 (DRL-) - E-8 Always Below 1 Ω
B-16 (PWM1) - E-6 Always Below 1 Ω


If the result is not as specified, replace the headlight unit assembly RH (headlight cord).


vi.

Inspect the turn signal light circuit.

Standard Resistance:
Tester Connection Condition Specified Condition
B-9 (TURN+) - E-4 Always Below 1 Ω
B-13 (TURN-) - E-2 Always Below 1 Ω


If the result is not as specified, replace the headlight unit assembly RH (headlight cord).



Hide 81131A 5.INSPECT HEADLIGHT UNIT RH

E371636C02
0.448,0.583 0.76,0.781 0.313,0.198 10 false *a
*a Component without harness connected
(Headlight Unit RH)


a.

Apply auxiliary battery voltage to the headlight unit RH and check that the Lo/Hi beam shade operates.

OK:
Condition Specified Condition
Auxiliary battery positive (+) → Terminal 10
Auxiliary battery negative (-) → Terminal 4
Operates normally


If the result is not as specified, replace the headlight unit RH.


Hide 81131B 6.INSPECT HEADLIGHT LENS RH

E371637C02
0.458,0.969 0.771,1.167 0.313,0.198 10 false *a
*a Component without harness connected
(Headlight Lens RH)


a.

Apply auxiliary battery voltage to the headlight lens RH and check that the light illuminates.

OK:
Condition Specified Condition
Auxiliary battery positive (+) → Terminal 4
Auxiliary battery negative (-) → Terminal 2
Clearance light/daytime running light illuminates


If the result is not as specified, replace the headlight lens RH.