Home › Vehicle Exterior › LIGHTING (EXT) › HEADLIGHT ASSEMBLY (for LED Type Turn Signal Light)
RM33C0E _59 Vehicle Exterior _065472 LIGHTING (EXT) _0330491 HEADLIGHT ASSEMBLY(for LED Type Turn Signal Light) A

LIGHTING (EXT)  HEADLIGHT ASSEMBLY(for LED Type Turn Signal Light)  DISASSEMBLY  


CAUTION / NOTICE / HINT

NOTICE:
·

Be sure to read Precaution thoroughly before servicing.

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for LED Type Turn Signal Light)>PRECAUTION

·

Handle components indoors as much as possible to prevent foreign matter from entering and adhering to headlight assembly components.

·

Do not reuse parts which have reduced fastening ability due to thread damage.

·

Do not touch the inner surface of the lens and metallic surfaces as much as possible, or they may become dirty.

·

Do not allow metallic surfaces to become dirty, as such surfaces become damaged even if they are only lightly wiped with a soft cloth.

·

When installing components, make sure that the wire harness is not pinched or pulled.

·

Do not use solvent to clean components. Only clean them with a dry cloth.



HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 81056A 1.REMOVE HEADLIGHT ECU SUB-ASSEMBLY

Hide 81134 2.REMOVE HEADLIGHT GASKET

Hide 81135F 3.REMOVE HEADLIGHT BACK COVER

a.
E371269C01
0,0 0,0 false
V113147

Remove in this Direction


Turn the headlight back cover as shown in the illustration to remove it.


Hide 81171B 4.REMOVE HEADLIGHT LENS

NOTICE:
·

Make sure to wear clean rubber gloves when performing this procedure.

·

Do not allow dirt or foreign matter to get on the headlight lens.

·

Prevention of static electricity is required during this procedure.

·

Use static electricity countermeasures SST (desktop anti-static mat set) and observe all precautions to prevent damage to the system by electrostatic discharge (ESD).

·

Do not touch the headlight lens with bare hands.

·

Do not touch the inner surface of the lens and metallic surfaces as much as possible, or they may become dirty.

·

Do not allow metallic surfaces to become dirty, as such surfaces become damaged even if they are only lightly wiped with a soft cloth.

·

If there are any fingerprints or foreign matter on the back of the headlight lens, wipe them off with a soft cloth.

·

Do not use solvent to clean components. Only clean them with a dry cloth.



SST
09890-47010  (09891-04010, 09891-04020, 09891-04030, 09891-04040)

a.
E371276

Remove the 4 screws.


b.
E371275C01
0,0 0,0 false
V100135

Screw
V100136

"TORX" screw


Remove the 4 screws.


c.

Using a T20H "TORX" driver, remove the "TORX" screw.


d.
E371277

Using a hair dryer, heat the backside of the headlight assembly.

NOTICE:

If the headlight assembly is heated unevenly, it will deform or melt.



e.
E371278

Disengage the 9 claws.


f.

Separate the headlight lens from the headlight housing sub-assembly.

HINT:

If the headlight lens cannot be separated even after heating, using a screwdriver with its tip wrapped with protective tape, lift the headlight lens. Be careful not to damage the headlight lens and headlight housing sub-assembly.



g.
E371279

Disconnect the connector to remove the headlight lens from the headlight housing sub-assembly.


Hide 81132B 5.REMOVE HEADLIGHT LENS GASKET

NOTICE:
·

The headlight lens gasket must not be reused.

·

Make sure to wear clean rubber gloves when performing this procedure.

·

Do not touch the inner surface of the lens and metallic surfaces as much as possible, or they may become dirty.

·

Do not allow metallic surfaces to become dirty, as such surfaces become damaged even if they are only lightly wiped with a soft cloth.

·

If there are any fingerprints or foreign matter on the headlight unit assembly or other components, wipe them off with a soft cloth.

·

Do not use solvent to clean components. Only clean them with a dry cloth.



a.
E371289

Remove the headlight lens gasket from the headlight housing sub-assembly.

NOTICE:

Make sure to replace the headlight lens gasket with a new one. Failure to do so may cause water ingress.



Hide 81171A 6.REMOVE HEADLIGHT UNIT

NOTICE:
·

Make sure to wear clean rubber gloves when performing this procedure.

·

Do not allow dirt or foreign matter to get on the headlight unit or other components.

·

Prevention of static electricity is required during this procedure.

·

Use static electricity countermeasures SST (desktop anti-static mat set) and observe all precautions to prevent damage to the system by electrostatic discharge (ESD).

·

Do not touch the headlight unit with bare hands.

·

Do not allow metallic surfaces to become dirty, as such surfaces become damaged even if they are only lightly wiped with a soft cloth.

·

If there are any fingerprints or foreign matter on the headlight unit or other components, wipe them off with a soft cloth.

·

Do not use solvent to clean components. Only clean them with a dry cloth.



SST
09890-47010  (09891-04010, 09891-04020, 09891-04030, 09891-04040)

a.
E371280

Disconnect the connector.


b.

Disengage the pivot collar.


c.
E371281C01
0,0 0,0 false
V113147

Turn in this Direction


While holding the headlight unit by hand, turn the aiming screws as shown in the illustration until the aiming screws are disconnected from the headlight unit.

HINT:

Make sure to remember the number of aiming screw rotations.



d.

Remove the headlight unit from the headlight housing sub-assembly.


Hide 85661A 7.REMOVE HEADLIGHT LEVELING MOTOR

a.
E371283

Disconnect the connector.


b.

Remove the 2 screws and headlight leveling motor from the headlight housing sub-assembly.


Hide 81102 8.REMOVE HEADLIGHT HOUSING SUB-ASSEMBLY

HINT:

As the headlight housing sub-assembly is available as a supply part, proceed to the next step if it is necessary to change the headlight housing sub-assembly.


a.
E436646

Disengage the 2 clamps to remove the headlight cord from the headlight housing sub-assembly.