Home › Vehicle Exterior › LIGHTING (EXT) › HEADLIGHT ASSEMBLY (for LED Type Turn Signal Light)
RM33C0E _59 Vehicle Exterior _065472 LIGHTING (EXT) _0330491 HEADLIGHT ASSEMBLY(for LED Type Turn Signal Light) A

LIGHTING (EXT)  HEADLIGHT ASSEMBLY(for LED Type Turn Signal Light)  REASSEMBLY  


CAUTION / NOTICE / HINT

NOTICE:
·

Handle components indoors as much as possible to prevent foreign matter from entering and adhering to headlight assembly components.

·

Do not reuse parts which have reduced fastening ability due to thread damage.

·

When installing components, make sure that the wire harness is not pinched or pulled.

·

Do not use solvent to clean components. Only clean them with a dry cloth.



HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 81102 1.INSTALL HEADLIGHT HOUSING SUB-ASSEMBLY

HINT:

As the headlight housing sub-assembly is available as a supply part, proceed to the next step if it is necessary to change the headlight housing sub-assembly.


a.
E436646

Engage the 2 clamps to install the headlight cord to the headlight housing sub-assembly.


Hide 85661A 2.INSTALL HEADLIGHT LEVELING MOTOR

a.
E371284

Install the headlight leveling motor with the 2 screws to the headlight housing sub-assembly.


b.

Connect the connector.


Hide 81171A 3.INSTALL HEADLIGHT UNIT

NOTICE:
·

Make sure to wear clean rubber gloves when performing this procedure.

·

Do not allow dirt or foreign matter to get on the headlight unit or other components.

·

Prevention of static electricity is required during this procedure.

·

Use static electricity countermeasures SST (desktop anti-static mat set) and observe all precautions to prevent damage to the system by electrostatic discharge (ESD).

·

Do not touch the headlight unit with bare hands.

·

Do not allow metallic surfaces to become dirty, as such surfaces become damaged even if they are only lightly wiped with a soft cloth.

·

If there are any fingerprints or foreign matter on the headlight unit or other components, wipe them off with a soft cloth.

·

Do not use solvent to clean components. Only clean them with a dry cloth.



SST
09890-47010  (09891-04010, 09891-04020, 09891-04030, 09891-04040)

a.

Temporarily install the headlight unit to the headlight housing sub-assembly.


b.
E371282C01
0,0 0,0 false
V113147

Turn in this Direction


While holding the headlight unit by hand, turn the aiming screws as shown in the illustration to install the headlight unit.

HINT:

Turn the aiming screws the same number of times as they were turned during removal.



c.
E371280

Engage the pivot collar.


d.

Connect the connector.


Hide 81132B 4.INSTALL HEADLIGHT LENS GASKET

NOTICE:
·

The headlight lens gasket must not be reused.

·

Make sure to wear clean rubber gloves when performing this procedure.

·

Do not touch the inner surface of the lens and metallic surfaces as much as possible, or they may become dirty.

·

Do not allow metallic surfaces to become dirty, as such surfaces become damaged even if they are only lightly wiped with a soft cloth.

·

If there are any fingerprints or foreign matter on the headlight unit assembly or other components, wipe them off with a soft cloth.

·

Do not use solvent to clean components. Only clean them with a dry cloth.



a.

Completely remove the old headlight lens gasket.


b.
E371289C01
0,0 0,0 false
V100155

Cleaning Area


Clean the installation groove of the headlight lens.


c.
E401542C01
1.417,1.417 1.417,1.167 false 0.75,1.25 0.75,1 false 2.125,2.021 2.125,1.771 false 1.354,1.427 1.667,1.583 0.313,0.156 10 false *a 0.688,1.271 1,1.427 0.313,0.156 10 false *b 2.042,2.021 2.354,2.177 0.313,0.156 10 false *c 1.51,0.552 1.667,0.75 0.156,0.198 10 false 1 0.302,0.719 0.458,0.917 0.156,0.198 10 false 2
*a Release Paper
*b Tape
*c 90°


Partially remove the release paper from a new headlight lens gasket, and cut off a piece of it.


d.

Fold the release paper over the tip of a screwdriver and secure it in place with tape as indicated by the arrows, in the order shown in the illustration.


e.

Using scissors, cut the end of the headlight lens gasket at a 90° angle.


f.
E371285C01
0,0 0,0 false
V100144

Starting Position


Starting from the position shown in the illustration and moving counterclockwise, temporarily install the headlight lens gasket as shown in the illustration.

NOTICE:

Gently install the headlight lens gasket without pulling it.



g.
E371286C01
0,0 0,0 false
V100135

Corner Groove


Set the headlight lens gasket into the corner groove.

NOTICE:
·

Gently install the headlight lens gasket without pulling it.

·

If the headlight lens gasket is pulled while it is installed, it will not be installed properly in the corner groove.




h.
E371287C01
0,0 0,0 false
V113147

Press in this Direction
V100155

Release Paper


Using 2 screwdrivers with their tips wrapped with release paper, completely press the headlight lens gasket into the groove to install it.

NOTICE:
·

Gently install the headlight lens gasket without pulling it.

·

If the headlight lens gasket is pulled while it is installed, it will not be installed properly in the corner groove.




i.
E371288C01
0.896,1.458 1.052,1.656 0.156,0.198 10 false A
V100135

Corner Groove


Repeat the following until the headlight lens gasket reaches the starting position: Temporarily install the headlight lens gasket to the straight groove and completely press it into the groove, and then temporarily install it to the corner groove and completely press it into the groove.


j.

Using scissors, cut the headlight lens gasket at a 45° angle at the starting position so that the headlight lens gasket overlaps itself 20 mm (0.7874 in.).

Standard Dimension:
Area Dimension
A 20 mm (0.7874 in.)



k.

Check the installation condition of the headlight lens gasket.

NOTICE:
·

Make sure the headlight lens gasket is not protruding and is installed properly.

·

Make sure there is no gap between the ends of the headlight lens gasket.

·

Make sure to thoroughly check the corners as the headlight lens gasket is likely to be improperly installed in the corners.




Hide 81171B 5.INSTALL HEADLIGHT LENS

NOTICE:
·

Make sure to wear clean rubber gloves when performing this procedure.

·

Do not allow dirt or foreign matter to get on the headlight lens.

·

Prevention of static electricity is required during this procedure.

·

Use static electricity countermeasures SST (desktop anti-static mat set) and observe all precautions to prevent damage to the system by electrostatic discharge (ESD).

·

Do not touch the headlight lens with bare hands.

·

Do not touch the inner surface of the lens and metallic surfaces as much as possible, or they may become dirty.

·

Do not allow metallic surfaces to become dirty, as such surfaces become damaged even if they are only lightly wiped with a soft cloth.

·

If there are any fingerprints or foreign matter on the back of the headlight lens, wipe them off with a soft cloth.

·

Do not use solvent to clean components. Only clean them with a dry cloth.



SST
09890-47010  (09891-04010, 09891-04020, 09891-04030, 09891-04040)

a.

Clean the sealing surface of the headlight lens.


b.
E371279

Connect the connector.


c.

Temporarily install the headlight lens to the headlight housing sub-assembly.

NOTICE:
E317610C01
0,0 0,0 false
V100144

Headlight Lens Gasket
V100146

Headlight Housing Sub-assembly
V100155

Headlight Lens


·

Temporarily install the headlight lens in the middle of the headlight lens gasket as shown in the illustration.

·

Check that the entire circumference of the headlight lens is positioned above the middle of the headlight lens gasket.




d.
E371278

Engage the 9 claws to install the headlight lens to the headlight housing sub-assembly.

NOTICE:

Make sure all of the claws are engaged.



e.
E371275C01
0,0 0,0 false
V100135

Screw
V100136

"TORX" screw


Using a T20H "TORX" driver, install the "TORX" screw.


f.

Install the 4 screws.


g.
E371276

Install the 4 screws.


h.

Check the installation condition of the headlight lens gasket.

NOTICE:

Make sure the headlight lens gasket is not protruding and completely contacts the headlight lens.



Hide 81135F 6.INSTALL HEADLIGHT BACK COVER

a.
E371270C01
2.813,1.115 2.552,0.76 2.552,0.76 2.823,0.875 true 2.385,0.677 2.698,0.875 0.313,0.198 10 false *a
*a Lock Mark
V113147

Install in this Direction


Turn the headlight back cover as shown in the illustration until the lock marks are aligned to install it.


Hide 81134 7.INSTALL HEADLIGHT GASKET

Hide 81056A 8.INSTALL HEADLIGHT ECU SUB-ASSEMBLY