The steering lock ECU (steering lock actuator or upper bracket assembly) activates the steering lock motor and moves the lock bar into the steering column to lock the steering.
The steering may not unlock when the lock bar gets stuck in the lock hole of the steering column. In this case, if the power switch is turned on (IG) while shaking the steering wheel, as is done for a vehicle with a mechanical key, the lock bar will be unlocked. If the certification ECU (smart key ECU assembly) or hybrid vehicle control ECU assembly is replaced, the system needs to be initialized. Otherwise, the steering cannot be unlocked and the hybrid control system cannot be started.
| Problem Symptom | Data List Item | Active Test Item |
|---|---|---|
| Unable to unlock steering wheel (Hybrid control system cannot start) | Smart Key
·
Unlock Request Receive ·
L Code Check ·
Steering Unlock |
- |
When using the GTS with the power switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
Perform either of the following operations to lock/unlock the steering:
To unlock the steering, carry the electrical key transmitter sub-assembly and turn the power switch on (ACC) or on (IG).
To lock the steering, turn the power switch off with the shift lever in P, and then open a door.
The smart entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the smart entry and start system (for Start Function) after confirming that the communication systems are functioning properly.
After performing repairs, confirm that the problem does not recur.
Make sure that no DTCs are output. If any DTCs are output, proceed to Diagnostic Trouble Code Chart.
Inspect the fuses for circuits related to this system before performing the following procedure.
Before replacing the steering lock ECU (steering lock actuator or upper bracket assembly) or certification ECU (smart key ECU assembly), refer to Service Bulletin.
When disconnecting the cable from the negative (-) auxiliary battery terminal, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
If the steering lock ECU (steering lock actuator or upper bracket assembly) is replaced, be sure to confirm that the steering is unlocked by turning the steering wheel to the left and right before starting the hybrid control system. This function prevents the hybrid control system from starting while the steering is locked. If the steering is locked for any reason, open and close a door with the power switch off, and then unlock the steering by pressing the power switch.
Check the power source mode change.
When the electrical key transmitter sub-assembly is inside the vehicle and the shift lever is in P, check that pressing the power switch with the brake pedal released causes the power source mode to change as follows:
Off → On (ACC) → On (IG) → Off
| Proceed to |
|---|
| OK |
| NG |
OK
NG
With the power switch on (IG), check that Steering Lock active is displayed on the multi-information display in the combination meter assembly.
| Result | Proceed to |
|---|---|
| Steering Lock active is displayed | A |
| Steering Lock active is not displayed | B |
A
B
Turn the steering wheel left and right, and then press the power switch.
Check that the steering is unlocked.
| Result | Proceed to |
|---|---|
| The steering is unlocked | A |
| The steering is not unlocked | B |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
Using the GTS, check if the certification ECU (smart key ECU assembly) DTC is output.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTCs are output | B |
A
B
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Entry&Start / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Unlock Request Receive | Status of steering unlock command from certification ECU (smart key ECU assembly) | OK or NG | OK: Certification ECU (smart key ECU assembly) sends steering unlock command (within 10 seconds of power switch turned on (ACC) or on (IG), or of hybrid control system start operation performed)
NG: Certification ECU (smart key ECU assembly) does not send steering unlock command (power switch not turned on (ACC) or on (IG), and hybrid control system start operation not performed) |
·
The hybrid control system cannot be started when an unlock request signal cannot be received. ·
If OK is not displayed even though the steering unlock conditions are met, the certification ECU (smart key ECU assembly) may be malfunctioning. |
| Tester Display |
|---|
| Unlock Request Receive |
Within 10 seconds of turning the power switch on (ACC) or on (IG) or starting the hybrid control system, the Data List item changes to "OK".
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| L Code Check | Verification result between certification ECU (smart key ECU assembly) and steering lock ECU (steering lock actuator or upper bracket assembly) | OK or NG | OK: Verification result normal
NG: Verification result abnormal |
When NG is displayed:
·
The ID code for the certification ECU (smart key ECU assembly) or steering lock ECU (steering lock actuator or upper bracket assembly) is not registered, or the certification ECU (smart key ECU assembly) or steering lock ECU (steering lock actuator or upper bracket assembly) is malfunctioning. ·
The steering cannot be locked. ·
The steering cannot be unlocked (the hybrid control system cannot be started). |
| Tester Display |
|---|
| L Code Check |
OK is displayed on the GTS.
Reasons for verification failure:
The steering lock ECU (steering lock actuator or upper bracket assembly) or certification ECU (smart key ECU assembly) is malfunctioning.
There is a problem with the communication between ECUs.
An ECU is replaced, but is not registered.
An ECU is replaced with an ECU which has a code already stored in it.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for Manual Tilt and Manual Telescopic Steering Column: Click hereSteering>STEERING COLUMN>STEERING COLUMN ASSEMBLY (for Manual Tilt and Manual Telescopic Steering Column)>DISASSEMBLY
for Power Tilt and Power Telescopic Steering Column: Click hereSteering>STEERING COLUMN>STEERING COLUMN ASSEMBLY (for Power Tilt and Power Telescopic Steering Column)>DISASSEMBLY
| *a | Component with harness connected
(Steering Lock ECU (Steering Lock Actuator or Upper Bracket Assembly)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K65-1 (GND) - Body ground | Always | Below 1 Ω |
If the result is not as specified, check for looseness in the ground cable connection.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K65-7 (B) - Body ground | Power switch off | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Move the shift lever to P and turn the power switch off.
Check the signal waveform according to the condition(s) in the table below.
| *a | Component with harness connected
(Steering Lock ECU (Steering Lock Actuator or Upper Bracket Assembly)) |
*b | Steering lock motor not operating |
| *c | Steering lock motor operating | *d | Waveform |
| Tester Connection | Condition | Tool Setting | Specified Condition |
|---|---|---|---|
| K65-3 (IGE) - K65-1 (GND) | 2 V/DIV., 200 ms./DIV. | Steering lock motor not operating → Operating → Not operating | Pulse generation
(See waveform) |
When taking measurements when the lock motor is stopped, it is not necessary to perform any operations.
In order to take measurements when the lock motor is operating, perform either of the following operations:
To unlock the steering, carry the electrical key transmitter sub-assembly and turn the power switch on (ACC) or on (IG).
To lock the steering, turn the power switch off with the shift lever in P, and then open a door.
| Proceed to |
|---|
| OK |
| NG |
OK
for Manual Tilt and Manual Telescopic Steering Column: Click hereSteering>STEERING COLUMN>STEERING COLUMN ASSEMBLY (for Manual Tilt and Manual Telescopic Steering Column)>DISASSEMBLY
for Power Tilt and Power Telescopic Steering Column: Click hereSteering>STEERING COLUMN>STEERING COLUMN ASSEMBLY (for Power Tilt and Power Telescopic Steering Column)>DISASSEMBLY
NG
Disconnect the K65 steering lock ECU (steering lock actuator or upper bracket assembly) connector.
Disconnect the K62 certification ECU (smart key ECU assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K65-3 (IGE) - K62-25 (SLR+) | Always | Below 1 Ω |
| K65-3 (IGE) or K62-25 (SLR+) - Other terminals and body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the K65 steering lock ECU (steering lock actuator or upper bracket assembly) connector.
Connect the K62 certification ECU (smart key ECU assembly) connector.
| *a | Component with harness connected
(Steering Lock ECU (Steering Lock Actuator or Upper Bracket Assembly)) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K65-3 (IGE) - Body ground | Power switch off | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for Manual Tilt and Manual Telescopic Steering Column: Click hereSteering>STEERING COLUMN>STEERING COLUMN ASSEMBLY (for Manual Tilt and Manual Telescopic Steering Column)>DISASSEMBLY
for Power Tilt and Power Telescopic Steering Column: Click hereSteering>STEERING COLUMN>STEERING COLUMN ASSEMBLY (for Power Tilt and Power Telescopic Steering Column)>DISASSEMBLY
| *a | Component with harness connected
(Steering Lock ECU (Steering Lock Actuator or Upper Bracket Assembly)) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K65-4 (SLP1) - Body ground | Steering locked | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the power switch off.
Check that the steering is locked.
Connect the GTS to the DLC3.
Turn the GTS on.
When using the GTS with the power switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
Enter the following menus: Body Electrical / Entry&Start / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Steering Unlock | Steering lock ECU (steering lock actuator or upper bracket assembly) unlock confirmation status | Unset or Set | Unset: Unlock not confirmed
Set: Unlock confirmed |
When Unset is displayed, the steering is not unlocked (the hybrid control system cannot be started). |
| Tester Display |
|---|
| Steering Unlock |
Set is displayed on the GTS.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for Manual Tilt and Manual Telescopic Steering Column: Click hereSteering>STEERING COLUMN>STEERING COLUMN ASSEMBLY (for Manual Tilt and Manual Telescopic Steering Column)>DISASSEMBLY
for Power Tilt and Power Telescopic Steering Column: Click hereSteering>STEERING COLUMN>STEERING COLUMN ASSEMBLY (for Power Tilt and Power Telescopic Steering Column)>DISASSEMBLY
Disconnect the K65 steering lock ECU (steering lock actuator or upper bracket assembly) connector.
Disconnect the K62 certification ECU (smart key ECU assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K65-4 (SLP1) - K62-14 (SLP) | Always | Below 1 Ω |
| K65-4 (SLP1) or K62-14 (SLP) - Other terminals and body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the steering lock ECU (steering lock actuator or upper bracket assembly) with a new one.
for Manual Tilt and Manual Telescopic Steering Column: Click hereSteering>STEERING COLUMN>STEERING COLUMN ASSEMBLY (for Manual Tilt and Manual Telescopic Steering Column)>DISASSEMBLY
for Power Tilt and Power Telescopic Steering Column: Click hereSteering>STEERING COLUMN>STEERING COLUMN ASSEMBLY (for Power Tilt and Power Telescopic Steering Column)>DISASSEMBLY
Perform registration.
Refer to Service Bulletin.
Turn the power switch on (IG).
Use the Data List to check if the steering lock request is functioning properly.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Unlock Request Receive | Status of steering unlock command from certification ECU (smart key ECU assembly) | OK or NG | OK: Certification ECU (smart key ECU assembly) sends steering unlock command (within 10 seconds of power switch turned on (ACC) or on (IG), or of hybrid control system start operation performed)
NG: Certification ECU (smart key ECU assembly) does not send steering unlock command (power switch not turned on (ACC) or on (IG), and hybrid control system start operation not performed) |
·
The hybrid control system cannot be started when an unlock request signal cannot be received. ·
If OK is not displayed even though the steering unlock conditions are met, the certification ECU (smart key ECU assembly) may be malfunctioning. |
| Tester Display |
|---|
| Unlock Request Receive |
Within 10 seconds of turning the power switch on (ACC) or on (IG) or starting the hybrid control system, the Data List item changes to "OK".
| Proceed to |
|---|
| OK |
| NG |
OK
NG