Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM (for Start Function) › 2017.09–2019.02
RM33C0E _58 Vehicle Interior _065456 THEFT DETERRENT / KEYLESS ENTRY _0330906 SMART ENTRY AND START SYSTEM(for Start Function) J

THEFT DETERRENT / KEYLESS ENTRY  SMART ENTRY AND START SYSTEM(for Start Function)  Power Source Mode does not Change to ON (IG and ACC)  


DESCRIPTION

When the power switch cannot be turned on (ACC) or on (IG), interior verification may be abnormal or there may be a malfunction in the ACC relay or IG relay circuit. If interior verification cannot be performed, the certification ECU (smart key ECU assembly) may be malfunctioning or communication may not be possible between the No. 1 indoor electrical key antenna assembly (front floor) or No. 1 indoor electrical key antenna assembly (rear floor) and the electrical key transmitter sub-assembly and door control receiver.

When an electrical key transmitter sub-assembly is brought into the cabin, its key ID code is compared with the key ID code stored in the certification ECU (smart key ECU assembly). If these codes do not match, key verification will fail and the power switch will not be able to be turned on (ACC) or on (IG).

When a door is unlocked and an electrical key transmitter sub-assembly is brought into the cabin, the certification ECU (smart key ECU assembly) activates the indoor electrical key antenna assemblies to form the interior detection area. The electrical key transmitter sub-assembly then responds to the detection signals with its key ID code. This response signal is received by the door control receiver and sent to the certification ECU (smart key ECU assembly).

Related Data List and Active Test Items
Problem Symptom Data List and Active Test
Power source mode does not change to on (IG) or on (ACC)
Power Source Control
·

Start Switch1

·

Start Switch2

·

IG Relay Monitor (Inside)

·

ACC Relay Monitor

·

IG Relay Monitor (Outside)

·

Latch Circuit

·

Power Supply Condition



WIRING DIAGRAM

B494137E01
2.49,1.448 2.802,1.646 0.313,0.198 10 false IC 0.104,0.417 0.969,0.823 0.865,0.406 10 false from Auxiliary Battery 2.219,0.448 2.552,0.698 0.333,0.25 10 false +B 2.219,0.979 2.552,1.229 0.333,0.25 10 false E 2.802,1.094 3.135,1.344 0.333,0.25 10 false +B 2.979,1.49 3.417,1.75 0.438,0.26 10 false ACCD 1.49,0.594 2.063,0.833 0.573,0.24 10 false AM2 0.375,5.313 0.948,5.552 0.573,0.24 10 false K63 0.375,5.479 1.427,5.74 1.052,0.26 10 false Power Switch 1.01,3.604 1.583,3.844 0.573,0.24 10 false SS1 0.865,4.854 1.438,5.094 0.573,0.24 10 false AGND 1.01,4.24 1.583,4.479 0.573,0.24 10 false SS2 1.375,3.604 1.948,3.844 0.573,0.24 10 false 5 1.375,4.229 1.948,4.469 0.573,0.24 10 false 1 1.354,4.844 1.927,5.083 0.573,0.24 10 false 6 2.052,5.875 2.625,6.115 0.573,0.24 10 false K62 4.115,5.771 6.781,6.01 2.667,0.24 10 false Instrument Panel Junction Block Assembly 4.635,5.479 5.427,5.719 0.792,0.24 10 false IG2-NO. 2 5.344,4.958 6.427,5.208 1.083,0.25 10 false ECU-IG2 NO. 3 5.469,3.75 6.271,3.99 0.802,0.24 10 false WASHER 5.344,2.563 6.458,2.823 1.115,0.26 10 false ECU-IG1 NO. 1 5.469,1.333 6.396,1.677 0.927,0.344 10 false ECU-ACC 4.823,1.865 5.396,2.104 0.573,0.24 10 false ACC 4.635,3.083 5.458,3.354 0.823,0.271 10 false IG1-NO. 1 4.646,4.281 5.448,4.5 0.802,0.219 10 false IG1-NO. 2 3.042,2.688 3.615,2.927 0.573,0.24 10 false IG1D 1.948,3.604 2.521,3.844 0.573,0.24 10 false 23 1.948,4.229 2.521,4.469 0.573,0.24 10 false 21 1.969,4.844 2.542,5.083 0.573,0.24 10 false 11 3.969,5.01 4.542,5.25 0.573,0.24 10 false 13 4.01,4.594 4.583,4.833 0.573,0.24 10 false 1 3.969,2.604 4.542,2.844 0.573,0.24 10 false 17 3.448,1.5 4.021,1.74 0.573,0.24 10 false 16 3.979,1.396 4.552,1.635 0.573,0.24 10 false 30 4,0.99 4.573,1.229 0.573,0.24 10 false 1 6.594,0.979 6.948,1.219 0.354,0.24 10 false 26 6.635,1.385 7.031,1.625 0.396,0.24 10 false 3 3.969,1.188 4.542,1.427 0.573,0.24 10 false 3F 3.969,1.573 4.542,1.813 0.573,0.24 10 false 3A 3.969,4.813 4.542,5.052 0.573,0.24 10 false 3E 3.969,5.208 4.542,5.448 0.573,0.24 10 false 3C 6.583,1.177 6.938,1.417 0.354,0.24 10 false 3D 6.583,1.573 6.938,1.813 0.354,0.24 10 false 3B 6.583,2.188 6.938,2.427 0.354,0.24 10 false 14 6.625,3.385 6.979,3.625 0.354,0.24 10 false 2 6.583,4.604 6.938,4.844 0.354,0.24 10 false 15 2.031,0.354 2.365,0.604 0.333,0.25 10 false 4 1.948,0.844 2.281,1.094 0.333,0.25 10 false 18 2.198,4.24 2.771,4.479 0.573,0.24 10 false SSW2 2.208,3.594 2.781,3.833 0.573,0.24 10 false SSW1 2.208,4.844 2.781,5.083 0.573,0.24 10 false AGND 2.052,6.042 3.583,6.49 1.531,0.448 10 false Certification ECU (Smart Key ECU Assembly) 2.677,3.115 3.01,3.365 0.333,0.25 10 false +B 2.813,2.323 3.146,2.573 0.333,0.25 10 false +B 2.479,2.646 2.792,2.844 0.313,0.198 10 false IC 3.073,4 3.385,4.198 0.313,0.198 10 false IC 3.969,2.792 4.542,3.031 0.573,0.24 10 false 3A 6.583,4.802 6.927,5.031 0.344,0.229 10 false 3C 6.583,3.594 6.927,3.823 0.344,0.229 10 false 3C 6.583,2.385 6.927,2.615 0.344,0.229 10 false 3C 3.438,2.698 4.01,2.938 0.573,0.24 10 false 17

B463104E10
1.51,0.719 2.427,0.917 0.917,0.198 10 false ANTE5 1.594,1.885 2.51,2.083 0.917,0.198 10 false CLGB 0.521,2.49 2.719,2.875 2.198,0.385 10 false No. 1 Indoor Electrical Key Antenna Assembly (Front Floor) 0.521,2.333 1.167,2.604 0.646,0.271 10 false K64 2.052,0.708 2.615,0.896 0.563,0.188 10 false 1 2.063,1.865 2.625,2.052 0.563,0.188 10 false 3 5.031,0.625 5.594,0.813 0.563,0.188 10 false 8 4.948,0.833 5.51,1.021 0.563,0.188 10 false K62 5.021,1.771 5.583,1.958 0.563,0.188 10 false 9 4.948,1.979 5.51,2.167 0.563,0.188 10 false K62 5.302,0.729 5.865,0.917 0.563,0.188 10 false CLG5 5.313,1.854 5.875,2.042 0.563,0.188 10 false CG5B 5.844,1.406 6.406,1.594 0.563,0.188 10 false IC 5.302,3.531 5.865,3.719 0.563,0.188 10 false CLG6 5.302,4.677 5.865,4.865 0.563,0.188 10 false CG6B 5.844,4.271 6.406,4.458 0.563,0.188 10 false IC 5.021,3.427 5.583,3.615 0.563,0.188 10 false 5 4.979,3.635 5.542,3.823 0.563,0.188 10 false R8 5.021,4.604 5.583,4.792 0.563,0.188 10 false 6 4.979,4.802 5.542,4.99 0.563,0.188 10 false R8 2.083,3.521 2.646,3.708 0.563,0.188 10 false 1 2.083,4.677 2.646,4.865 0.563,0.188 10 false 3 1.521,3.531 2.083,3.719 0.563,0.188 10 false ANTE6 1.615,4.677 2.177,4.865 0.563,0.188 10 false CLGB 0.51,5.135 1.385,5.5 0.875,0.365 10 false R10 0.51,5.292 2.698,5.896 2.188,0.604 10 false No. 1 Indoor Electrical Key Antenna Assembly (Rear Floor) 5.073,5.49 6.594,6.146 1.521,0.656 10 false Certification ECU (Smart Key ECU Assembly)

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the power switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The smart entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the smart entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Make sure that no DTCs are output. If any DTCs are output, proceed to Diagnostic Trouble Code Chart.

·

If the smart entry and start system (for Start Function) has been disabled, enable the system before performing troubleshooting.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Start Function)>CUSTOMIZE PARAMETERS

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before replacing the certification ECU (smart key ECU assembly) or an electrical key transmitter sub-assembly, refer to Service Bulletin.

·

After completing repairs, confirm that the problem does not recur.

·

After performing repairs, confirm that no DTCs are output by performing "DTC Output Confirmation Operation."

·

The indoor electrical key antenna assemblies have an antenna coil between each terminal.

·

The door control receiver is also related to interior certification.



HINT:
·

If interior verification is unsuccessful, Operation History may be stored.

·

If Operation History has been stored, refer to the Operation History List to determine the detection conditions and narrow down trouble areas.



Body Electrical > Entry&Start > Utility
Tester Display
Operation History
50005 125 52

PROCEDURE

1.CHECK POWER SOURCE MODE
a.

Get into the vehicle while carrying the electrical key transmitter sub-assembly that has already been registered.


b.

Move the shift lever to P.


c.

Press the power switch with the brake pedal released and check that the power source mode changes.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Start Function)>OPERATION CHECK


Result:
Result Proceed to
Power source mode can only be changed when electrical key transmitter sub-assembly is in push button start function operation range for rear side A
Power source mode can only be changed when electrical key transmitter sub-assembly is in push button start function operation range for front side B
Power source mode cannot be changed C



A

2.CHECK WAVE ENVIRONMENT

B

6.CHECK WAVE ENVIRONMENT

C

10.INSPECT TRANSMITTER BATTERY
2.CHECK WAVE ENVIRONMENT
a.

Install the transmitter battery to the electrical key transmitter sub-assembly.

Click hereVehicle Interior>DOOR LOCK>DOOR CONTROL TRANSMITTER>INSTALLATION


b.

Bring the electrical key transmitter sub-assembly near the No. 1 indoor electrical key antenna assembly (front floor) and perform a smart entry and start system check.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Start Function)>OPERATION CHECK

NOTICE:

Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the No. 1 indoor electrical key antenna assembly (front floor).



HINT:
·

As the effect of wave interference decreases by moving the electrical key transmitter sub-assembly close to each indoor electrical key antenna assembly, it may be possible to check whether wave interference is the cause of the problem.

·

If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.

·

There may be wave interference if the vehicle is near broadcasting antennas, large video displays, wireless garage door opener systems, wireless security cameras, home security systems, etc. In this case, move the vehicle to a different location and check if there is any improvement.

·

If a tool for checking radio waves, such as a signal strength meter, is available, move around the area while observing both the LF band (used by the vehicle antenna to form the detection area) and RF band (used by the electrical key transmitter sub-assembly for transmission) to check for locations where there is wave interference.



OK:

The hybrid control system starts when the electrical key transmitter sub-assembly is held near each indoor electrical key antenna assembly and the power switch is pressed with the brake pedal depressed.


Result:
Proceed to
OK
NG



OK

AFFECTED BY WAVE INTERFERENCE

NG

3.CHECK KEY DIAGNOSTIC MODE
3.CHECK KEY DIAGNOSTIC MODE
a.

Check the following antennas in key diagnostic mode.


b.
B477777C01
0.719,1.042 2.771,0.208 2.771,0.208 2.948,0.208 false 2.167,1.021 2.76,0.208 false 2.979,0.125 3.292,0.281 0.313,0.156 10 false *a
*a Inspection Point


Check the No. 1 indoor electrical key antenna assembly (front floor).

When the electrical key transmitter sub-assembly is at either inspection point, check that the wireless buzzer sounds.

HINT:
·

Select either channel 1 or channel 2 and perform the key diagnostic mode inspection for each channel.

·

If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.

·

It is possible to check which No. 1 indoor electrical key antenna assembly (front floor, rear floor or inside luggage compartment) is operating by the sounding of the buzzer.

·

When the wireless buzzer sounds for all indoor electrical key antenna assemblies, they can be judged as operating properly and a malfunction in the certification ECU (smart key ECU assembly), which performs verification, is suspected.

·

When the wireless buzzer does not sound for all indoor electrical key antenna assemblies, it can be judged that the certification ECU (smart key ECU assembly), which controls the indoor electrical key antenna assemblies, is malfunctioning.



Body Electrical > Entry&Start > Utility
Tester Display
Communication Check(Key Diag Mode)
50005 125 143

Result:
Result Proceed to
The wireless buzzer does not sound A
The wireless buzzer sounds B



A

4.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (FRONT FLOOR))

B

AFFECTED BY WAVE INTERFERENCE

4.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (FRONT FLOOR))
a.

Disconnect the K62 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the K64 No. 1 indoor electrical key antenna assembly (front floor) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K62-8 (CLG5) - K64-1 (ANTE5) Always Below 1 Ω
K62-9 (CG5B) - K64-3 (CLGB) Always Below 1 Ω
K62-8 (CLG5) or K64-1 (ANTE5) - Other terminals and body ground Always 10 kΩ or higher
K62-9 (CG5B) or K64-3 (CLGB) - Other terminals and body ground Always 10 kΩ or higher



d.

Reconnect the K62 certification ECU (smart key ECU assembly) connector.


Result:
Proceed to
OK
NG



OK

5.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (FRONT FLOOR))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (FRONT FLOOR))
a.

Using an oscilloscope, check the waveform.

B431370C50
1.583,0.5 2,0.75 0.417,0.25 1.365,2.104 1.615,2.104 1.615,2.104 1.615,1.604 true 2.271,2.104 2.021,2.104 2.021,2.104 2.021,1.604 true 0.448,0.271 0.76,0.427 0.313,0.156 10 false *a 3.604,0.271 3.917,0.427 0.313,0.156 10 false *b 4.75,1.969 5.063,2.125 0.313,0.156 10 false *c 5.552,1.979 5.865,2.135 0.313,0.156 10 false *d 1.656,0.542 1.99,0.75 0.333,0.208 10 false K64 2.323,2.01 3.052,2.292 0.729,0.281 10 false CLGB 3.969,1.271 4.281,1.427 0.313,0.156 10 false GND 0.906,2.01 1.646,2.292 0.74,0.281 10 false ANTE5
*a Front view of wire harness connector
(to No. 1 Indoor Electrical Key Antenna Assembly (Front Floor))
*b Waveform
*c For 30 seconds after closing any door *d After 30 seconds or more have elapsed since any door closed


OK:
Tester Connection Condition Tool Setting Specified Condition
K64-1 (ANTE5) - K64-3 (CLGB) Procedure:
1.

Power switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Within 30 seconds of closing any door


2 V/DIV., 500 ms/DIV. Pulse generation
(See waveform)



Result:
Proceed to
OK
NG



OK

REPLACE NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (FRONT FLOOR)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

6.CHECK WAVE ENVIRONMENT
a.

Install the transmitter battery to the electrical key transmitter sub-assembly.

Click hereVehicle Interior>DOOR LOCK>DOOR CONTROL TRANSMITTER>INSTALLATION


b.

Bring the electrical key transmitter sub-assembly near the No. 1 indoor electrical key antenna assembly (rear floor) and perform a smart entry and start system check.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Start Function)>OPERATION CHECK

NOTICE:

Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the center of the No. 1 indoor electrical key antenna assembly (rear floor).


HINT:

Check that the customize setting "Ignition Available Area" is set to "All".



HINT:
·

As the effect of wave interference decreases by moving the electrical key transmitter sub-assembly close to each indoor electrical key antenna assembly, it may be possible to check whether wave interference is the cause of the problem.

·

If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.

·

There may be wave interference if the vehicle is near broadcasting antennas, large video displays, wireless garage door opener systems, wireless security cameras, home security systems, etc. In this case, move the vehicle to a different location and check if there is any improvement.

·

If a tool for checking radio waves, such as a signal strength meter, is available, move around the area while observing both the LF band (used by the vehicle antenna to form the detection area) and RF band (used by the electrical key transmitter sub-assembly for transmission) to check for locations where there is wave interference.



OK:

The hybrid control system starts when the electrical key transmitter sub-assembly is held near each indoor electrical key antenna assembly and the power switch is pressed with the brake pedal depressed.


Result:
Proceed to
OK
NG



OK

AFFECTED BY WAVE INTERFERENCE

NG

7.CHECK KEY DIAGNOSTIC MODE
7.CHECK KEY DIAGNOSTIC MODE
a.

Check the following antennas in key diagnostic mode.


b.
B477778C01
0.708,0.521 2.865,0.229 2.865,0.229 3.021,0.229 false 2.135,0.521 2.854,0.229 false 3.073,0.135 3.385,0.292 0.313,0.156 10 false *a
*a Inspection Point


Check the No. 1 indoor electrical key antenna assembly (rear floor).

When the electrical key transmitter sub-assembly is at either inspection point, check that the wireless buzzer sounds.

HINT:
·

Select either channel 1 or channel 2 and perform the key diagnostic mode inspection for each channel.

·

If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.

·

It is possible to check which No. 1 indoor electrical key antenna assembly (front floor, rear floor or inside luggage compartment) is operating by the sounding of the buzzer.

·

When the wireless buzzer sounds for all indoor electrical key antenna assemblies, they can be judged as operating properly and a malfunction in the certification ECU (smart key ECU assembly), which performs verification, is suspected.

·

When the wireless buzzer does not sound for all indoor electrical key antenna assemblies, it can be judged that the certification ECU (smart key ECU assembly), which controls the indoor electrical key antenna assemblies, is malfunctioning.



Body Electrical > Entry&Start > Utility
Tester Display
Communication Check(Key Diag Mode)
50005 125 143

Result:
Result Proceed to
The wireless buzzer does not sound A
The wireless buzzer sounds B



A

8.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (REAR FLOOR))

B

AFFECTED BY WAVE INTERFERENCE

8.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (REAR FLOOR))
a.

Disconnect the R8 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the R10 No. 1 indoor electrical key antenna assembly (rear floor) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R8-5 (CLG6) - R10-1 (ANTE6) Always Below 1 Ω
R8-6 (CG6B) - R10-3 (CLGB) Always Below 1 Ω
R8-5 (CLG6) or R10-1 (ANTE6) - Other terminals and body ground Always 10 kΩ or higher
R8-6 (CG6B) or R10-3 (CLGB) - Other terminals and body ground Always 10 kΩ or higher



d.

Reconnect the R8 certification ECU (smart key ECU assembly) connector.


Result:
Proceed to
OK
NG



OK

9.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (REAR FLOOR))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (REAR FLOOR))
a.

Using an oscilloscope, check the waveform.

B431370C51
1.583,0.5 2,0.75 0.417,0.25 1.354,2.104 1.604,2.104 1.604,2.104 1.604,1.604 true 2.271,2.104 2.021,2.104 2.021,2.104 2.021,1.604 true 0.448,0.271 0.76,0.427 0.313,0.156 10 false *a 3.604,0.271 3.917,0.427 0.313,0.156 10 false *b 4.75,1.969 5.063,2.125 0.313,0.156 10 false *c 5.552,1.979 5.865,2.135 0.313,0.156 10 false *d 1.667,0.542 1.979,0.729 0.313,0.188 10 false R10 2.323,2.01 3.052,2.292 0.729,0.281 10 false CLGB 3.969,1.271 4.281,1.427 0.313,0.156 10 false GND 0.875,2.01 1.615,2.292 0.74,0.281 10 false ANTE6
*a Front view of wire harness connector
(to No. 1 Indoor Electrical Key Antenna Assembly (Rear Floor))
*b Waveform
*c For 30 seconds after closing any door *d After 30 seconds or more have elapsed since any door closed


OK:
Tester Connection Condition Tool Setting Specified Condition
R10-1 (ANTE6) - R10-3 (CLGB) Procedure:
1.

Power switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Within 30 seconds of closing any door


2 V/DIV., 500 ms/DIV. Pulse generation
(See waveform)



Result:
Proceed to
OK
NG



OK

REPLACE NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (REAR FLOOR)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

10.INSPECT TRANSMITTER BATTERY
a.

Check the transmitter battery level of the electrical key transmitter sub-assembly that was checked first.

i.

Press and hold the lock switch of the electrical key transmitter sub-assembly for 5 seconds and check the number of times that the LED illuminates.

HINT:
·

The electrical key transmitter sub-assembly sends voltage information to the certification ECU (smart key ECU assembly) when it is being used. "Yes" is displayed for the Data List item Key Low Battery when this voltage information indicates 2.2 V or less.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Start Function)>DATA LIST / ACTIVE TEST

·

Even if the transmitter battery is depleted, it is still possible to start the hybrid control system by holding the electrical key transmitter sub-assembly near the power switch, depressing the brake pedal and pressing the power switch.





Result:
Result Proceed to
LED illuminates 3 times or more when switch is pressed and held A
LED does not illuminate when switch is pressed and held B
LED illuminates once or twice but not a third time C



A

11.CHECK ENTRY LOCK / UNLOCK OPERATION

B

19.INSPECT TRANSMITTER BATTERY

C

REPLACE TRANSMITTER BATTERY

11.CHECK ENTRY LOCK / UNLOCK OPERATION
a.

Check that the entry lock and unlock functions operate on each door.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Start Function)>OPERATION CHECK

HINT:

If the door control receiver is defective, code verification does not begin in the cabin and the entry lock and unlock functions do not operate.



Result:
Result Proceed to
Entry functions operate normally for all doors (w/ Wireless Charging System) A
Entry functions operate normally for all doors (w/o Wireless Charging System) B
An entry function does not operate normally for a door C



A

12.CHECK WIRELESS CHARGING SYSTEM

B

13.READ VALUE USING GTS (START SWITCH1, START SWITCH2)

C

GO TO SMART ENTRY AND START SYSTEM (for Entry Function) (All Door Entry Lock/Unlock Functions and Wireless Functions do not Operate)

12.CHECK WIRELESS CHARGING SYSTEM


Result:
Result Proceed to
Interior verification is not performed normally A
Interior verification is performed normally B



A

13.READ VALUE USING GTS (START SWITCH1, START SWITCH2)

B

13.READ VALUE USING GTS (START SWITCH1, START SWITCH2)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Power Source Control / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Start Switch1 Power switch 1 status OFF or ON OFF: Power switch not pressed
ON: Power switch pressed
·

If the power switch is pressed for a short time, the display may not change.

·

Use this item to determine if the power switch input signal is malfunctioning.


Start Switch2 Power switch 2 status OFF or ON OFF: Power switch not pressed
ON: Power switch pressed
·

Backup for power switch 1. However, when the power switch is pressed and held, the control functions only when both power switch 1 and 2 are normal.

·

Behaves the same way as power switch 1.


Body Electrical > Power Source Control > Data List
Tester Display
Start Switch1
Start Switch2
50003 223 4,5
OK:

The value of "Start Switch1" and "Start Switch2" change correctly in response to the power switch operation.



Result:
Proceed to
OK
NG



OK

14.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

17.INSPECT POWER SWITCH
14.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Measure the voltage while checking the Data List on the GTS.

i.

Connect the GTS to the DLC3.


ii.

Turn the power switch on (IG).


iii.

Turn the GTS on.


iv.

Enter the following menus: Body Electrical / Power Source Control / Data List.


v.

Read the Data List according to the display on the GTS.

B416787C29
4.583,0.417 5,0.667 0.417,0.25 4,2.333 4.25,2.333 4.25,2.333 4.25,1.333 true 4.583,2.333 4.333,2.333 4.333,2.333 4.333,1.333 true 4.656,0.469 4.969,0.667 0.313,0.198 10 false K62 3.667,2.24 4.094,2.469 0.427,0.229 10 false IG1D 0.198,0.156 0.51,0.354 0.313,0.198 10 false *a 4.615,2.229 5.073,2.438 0.458,0.208 10 false ACCD
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
- -


Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Power Supply Condition Power supply state All OFF, ACC ON, IG ON or ST ON All OFF: Power switch off (ACC and IG)
ACC ON: Power switch on (ACC)
IG ON: Power switch on (IG)
ST ON: Sending hybrid control system start request signal
-
Body Electrical > Power Source Control > Data List
Tester Display
Power Supply Condition
50003 223 18

vi.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
K62-17 (IG1D) - Body ground Power switch off Below 1 V
Power switch on (ACC) Below 1 V
Power switch on (IG) 9 V or higher
K62-16 (ACCD) - Body ground Power switch off Below 1 V
Power switch on (ACC) 8.5 V or higher
Power switch on (IG) 8.5 V or higher




Result:
Proceed to
OK
NG



OK

15.CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (ACC, IG1-NO. 1, IG1-NO. 2, IG2-NO. 2 RELAY)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

15.CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (ACC, IG1-NO. 1, IG1-NO. 2, IG2-NO. 2 RELAY)
a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Connect all of the instrument panel junction block assembly connectors.


c.

Measure the voltage according to the value(s) in the table below.

B463118C10
2.167,2.333 2.583,2.583 0.417,0.25 3.667,2.333 4.083,2.583 0.417,0.25 0.083,0.125 0.396,0.281 0.313,0.156 10 false *a 2.292,2.375 2.604,2.531 0.313,0.156 10 false 3D 3.781,2.375 4.094,2.531 0.313,0.156 10 false 3C
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


Standard Voltage:
Tester Connection Condition Specified Condition
3D-26 - Body ground Power switch on (ACC) 11 to 14 V
3C-14 - Body ground Power switch on (IG) 11 to 14 V
3C-2 - Body ground Power switch on (IG) 11 to 14 V
3C-15 - Body ground Power switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

16.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - BODY GROUND)
16.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - BODY GROUND)
a.

Disconnect the 3B instrument panel junction block assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3B-3 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

17.INSPECT POWER SWITCH


Result:
Proceed to
OK
NG



OK

18.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - POWER SWITCH)

NG

18.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - POWER SWITCH)
a.

Disconnect the K62 certification ECU (smart key ECU assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K62-23 (SSW1) - K63-5 (SS1) Always Below 1 Ω
K62-21 (SSW2) - K63-1 (SS2) Always Below 1 Ω
K62-11 (AGND) - K63-6 (AGND) Always Below 1 Ω
K62-23 (SSW1) or K63-5 (SS1) - Other terminals and body ground Always 10 kΩ or higher
K62-21 (SSW2) or K63-1 (SS2) - Other terminals and body ground Always 10 kΩ or higher
K62-11 (AGND) or K63-6 (AGND) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

19.INSPECT TRANSMITTER BATTERY
a.

Inspect the transmitter battery.

Click hereVehicle Interior>DOOR LOCK>DOOR CONTROL TRANSMITTER>INSPECTION

NOTICE:

Do not wrap the lead wire ground a terminal, wedge it between terminals, or solder it. The terminal may be deformed or damaged, and the transmitter battery will not be able to be installed correctly.



Result:
Proceed to
OK
NG



OK

REPLACE ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY

NG

REPLACE TRANSMITTER BATTERY