Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM (w/ Automatic Headlight Beam Level Control System) › 2017.09–2017.12
RM33C0E _59 Vehicle Exterior _065472 LIGHTING (EXT) _0331112 LIGHTING SYSTEM D

LIGHTING (EXT)  LIGHTING SYSTEM  INITIALIZATION  


NOTICE:
·

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during headlight ECU sub-assembly LH removal/installation are shown below.

Performed Work or System Condition Necessary Procedures Proceed to
Replacement of the headlight ECU sub-assembly LH Synchronize the vehicle information SYNCHRONIZE VEHICLE INFORMATION
Perform headlight ECU sub-assembly LH initialization HEADLIGHT ECU SUB-ASSEMBLY LH INITIALIZATION
Replacement of the rear height control sensor sub-assembly LH, removal and reinstallation of the rear height control sensor sub-assembly LH, replacement of the suspension, etc. have been performed Perform headlight ECU sub-assembly LH initialization HEADLIGHT ECU SUB-ASSEMBLY LH INITIALIZATION

·

A new headlight ECU sub-assembly LH cannot operate until the vehicle information is registered.

·

After replacing the headlight ECU sub-assembly LH, it is necessary to perform vehicle information registration and initialization.

·

Even if the headlight ECU sub-assembly RH is replaced with a new one, synchronize the vehicle information and initialization are not necessary.

·

Adjust the headlight aim after initializing the headlight ECU sub-assembly LH.

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for LED Type Turn Signal Light)>ADJUSTMENT

·

When a malfunction is detected in the lighting system, rear height control sensor sub-assembly LH signal initialization is impossible. Perform troubleshooting before initialization.

·

The lighting system uses the CAN communication system. First, confirm that there are no malfunctions in the CAN communication system. Refer to the How to Proceed with Troubleshooting procedure.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (w/ Automatic Headlight Beam Level Control System)>HOW TO PROCEED WITH TROUBLESHOOTING



SYNCHRONIZE VEHICLE INFORMATION (When using the GTS)


NOTICE:
·

Make sure to synchronize the vehicle information before performing initialization.

·

If synchronization fails, make sure to turn the power switch off then back on (IG) before performing synchronization again.



a.

Turn the power switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the power switch on (IG).


d.

Check that the "Headlight Auto Leveling System Unavailable Visit Your Dealer" warning message is displayed on the multi-information display.


e.

Enter the following menus: Body Electrical / HL AutoLeveling / Utility / ECU Information Sync.

Body Electrical > HL AutoLeveling > Utility
Tester Display
ECU Information Sync
50005 361 4272

f.

Check the display on the GTS and press "Next".


g.

Check that the "Headlight System Malfunction Visit Your Dealer" warning message continuously blinks 6 times at 2 Hz on the multi-information display.

HINT:
·

If the "Headlight System Malfunction Visit Your Dealer" warning message does not start blinking on the multi-information display after perform the procedure again.

·

If the "Headlight System Malfunction Visit Your Dealer" warning message changes from blinking to displayed on the multi-information display, the rear height control sensor sub-assembly LH may be malfunctioning.




h.

Press "Exit".


i.

Turn the power switch off.

NOTICE:

After synchronizing the vehicle information, initialize the headlight ECU sub-assembly LH.




SYNCHRONIZE VEHICLE INFORMATION (When not using the GTS)


NOTICE:
·

Make sure to synchronize the vehicle information before performing initialization.

·

If synchronization fails, make sure to turn the power switch off then back on (IG) before performing synchronization again.



a.

Turn the power switch on (IG).


b.

Check that the "Headlight Auto Leveling System Unavailable Visit Your Dealer" warning message is displayed on the multi-information display.


c.

Using the headlight dimmer switch, turn the low beam headlights on and off 8 times within 20 seconds after turning the power switch on (IG).

NOTICE:

If the low beam headlights illuminate when the power switch is on (IG), shine a light on the automatic light control sensor to turn the low beam headlights off before operating the headlight dimmer switch.


HINT:

If this step cannot be completed within 20 seconds, turn the power switch off. Then, turn the power switch on (IG) and restart the procedure.



d.

Check that the "Headlight System Malfunction Visit Your Dealer" warning message continuously blinks 6 times at 2 Hz on the multi-information display.

HINT:
·

If the "Headlight System Malfunction Visit Your Dealer" warning message does not start blinking on the multi-information display after perform the procedure again.

·

If the "Headlight System Malfunction Visit Your Dealer" warning message changes from blinking to displayed on the multi-information display, turn the power switch off and then on (IG). If "Headlight System Malfunction Visit Your Dealer" is displayed immediately after the power switch is turned on (IG), the rear height control sensor sub-assembly LH may be malfunctioning.




e.

Turn the power switch off.

NOTICE:

After synchronizing the vehicle information, initialize the headlight ECU sub-assembly LH.




HEADLIGHT ECU SUB-ASSEMBLY LH INITIALIZATION (When using the GTS)


NOTICE:

Make sure to synchronize the vehicle information before performing initialization.


a.

Prepare vehicle for initialization

·

Unload the vehicle, ensuring that the spare tire, tools and jack are in their original positions.

·

Check that there are no occupants in the vehicle.

·

Turn the light control switch to the AUTO position.*

·

Stop the vehicle on a level surface and keep the vehicle height unchanged.


HINT:

*: Turn off the headlights.



b.

Check the "Headlight System Malfunction Visit Your Dealer" warning message on the multi-information display.

i.

Turn the power switch on (IG), and check the condition of the "Headlight System Malfunction Visit Your Dealer" warning message on the multi-information display.

OK:
Condition Specified Condition
The headlight ECU sub-assembly LH has been replaced with a new one. "Headlight System Malfunction Visit Your Dealer" blinks 6 times at 2 Hz.
Replacement of the rear height control sensor sub-assembly LH, removal and reinstallation of the rear height control sensor sub-assembly LH, replacement of the suspension, etc. have been performed. "Headlight System Malfunction Visit Your Dealer" is not displayed.


HINT:

If the condition of the "Headlight System Malfunction Visit Your Dealer" warning message is different than listed in the table above, the headlight ECU sub-assembly LH or combination meter assembly may be malfunctioning.




c.

Perform initialization.

i.

Turn the power switch off.


ii.

Connect the GTS to the DLC3.


iii.

Turn the power switch on (IG).


iv.

Enter the following menus: Body Electrical / HL AutoLeveling / Utility / Height Sensor Initialization.

Body Electrical > HL AutoLeveling > Utility
Tester Display
Height Sensor Initialization
50005 361 4271

v.

Check the display on the GTS and press "Next".


vi.
E370557C02
0.177,0.146 0.49,0.344 0.313,0.198 10 false *a 0.302,1.458 0.615,1.656 0.313,0.198 10 false A 0.875,1.74 1.188,1.938 0.313,0.198 10 false B 1.698,1.75 2.01,1.948 0.313,0.198 10 false C 2.448,1.49 2.76,1.688 0.313,0.198 10 false D 3.01,0.896 3.323,1.094 0.313,0.198 10 false E
*a Fuel Receiver Gauge


Check the proper "Position ID" by the fuel level according to the table below.

HINT:

The "Position ID" is determined by the present fuel level as shown below.

Fuel Level Position ID Number of Times Headlight Leveling Warning Blinks
Within A range EMPTY 1
Within B range 1/4 to over EMPTY 2
Within C range 1/2 to over 1/4 3
Within D range 3/4 to over 1/2 4
Within E range FULL to over 3/4 5



vii.

Select the proper "Position ID" and press "Next".


viii.

Press "Exit".


ix.

Check the condition of the "Headlight System Malfunction Visit Your Dealer" warning message on the multi-information display.

Standard:
Condition Specified Condition
The headlight ECU sub-assembly LH has been replaced with a new one. Blinks 6 times at 2 Hz → Continuously blinks N* times at 2 Hz.
Replacement of the rear height control sensor sub-assembly LH, removal and reinstallation of the rear height control sensor sub-assembly LH, replacement of the suspension, etc. have been performed. Off → Continuously blinks N* times at 2 Hz.


HINT:
·

*: The number of times that "Headlight System Malfunction Visit Your Dealer" warning message blinks is determined by the "Position ID" selected.

·

If the "Headlight System Malfunction Visit Your Dealer" warning message is displayed on the multi-information display, the headlight ECU sub-assembly LH may be malfunctioning.

·

If initialization does not finish normally, restart the initialization procedure from step (i).




x.

Check that initialization finishes normally and turn the power switch off.

HINT:

The warning message will blink in the pattern indicating that initialization has completed successfully continuously until the power switch is turned off.





HEADLIGHT ECU SUB-ASSEMBLY LH INITIALIZATION (When not using the GTS)


NOTICE:

Make sure to synchronize the vehicle information before performing initialization.


a.

Prepare vehicle for initialization

·

Unload the vehicle, ensuring that the spare tire, tools and jack are in their original positions.

·

Check that there are no occupants in the vehicle.

·

Turn the light control switch to the AUTO position.*

·

Stop the vehicle on a level surface and keep the vehicle height unchanged.


HINT:

*: Turn off the headlights.



b.

Check the "Headlight System Malfunction Visit Your Dealer" warning message on the multi-information display.

i.

Turn the power switch on (IG), and check the condition of the "Headlight System Malfunction Visit Your Dealer" warning message on the multi-information display.

OK:
Condition Specified Condition
The headlight ECU sub-assembly LH has been replaced with a new one. "Headlight System Malfunction Visit Your Dealer" blinks 6 times at 2 Hz.
Replacement of the rear height control sensor sub-assembly LH, removal and reinstallation of the rear height control sensor sub-assembly LH, replacement of the suspension, etc. have been performed. "Headlight System Malfunction Visit Your Dealer" is not displayed.


HINT:

If the condition of the "Headlight System Malfunction Visit Your Dealer" warning message is different than listed in the table above, the headlight ECU sub-assembly LH or combination meter assembly may be malfunctioning.




c.

Perform initialization.

i.

Turn the power switch on (IG).


ii.
E370557C02
0.177,0.146 0.49,0.344 0.313,0.198 10 false *a 0.302,1.458 0.615,1.656 0.313,0.198 10 false A 0.875,1.74 1.188,1.938 0.313,0.198 10 false B 1.698,1.75 2.01,1.948 0.313,0.198 10 false C 2.448,1.49 2.76,1.688 0.313,0.198 10 false D 3.01,0.896 3.323,1.094 0.313,0.198 10 false E
*a Fuel Receiver Gauge


Check the specified number of times to turn the low beam headlights on and off.

HINT:

The number of times the low beam headlights need to be turned on and off is determined by the present fuel level as shown below.

Fuel Level Number of Times to Turn Low Beam Headlights On and Off
Within A range 1
Within B range 2
Within C range 3
Within D range 4
Within E range 5



iii.

Enter initialization mode.

1.

Turn the power switch off.

2.

Turn the light control switch to the AUTO position.*

HINT:

*: Turn off the headlights.


3.

Shine a light on the automatic light control sensor.

4.

Perform the following steps within 5 seconds.

(a)

Turn the power switch on (IG).

(b)

While pulling the headlight dimmer switch, turn it from AUTO to tail to AUTO again 3 times or more.

HINT:

Check that the clearance lights turn from off to on and back off again.


(c)

Turn the light control switch to the AUTO position.*

HINT:

*: Turn off the headlights.




HINT:
·

Perform the above operation within 5 seconds.

·

When initialization mode has been entered, "Headlight System Malfunction Visit Your Dealer" warning message on the multi-information display starts blinking at 1 Hz.




iv.

After entering initialization mode, turn the low beam headlights from off to on and back off again N* times.

HINT:
·

*: The number of times to turn the light control switch tail and head (N) is determined by the fuel level of the fuel receiver gauge.

·

Turn the light control switch tail and head within 20 seconds of entering initialization mode.

·

Turn the light control switch tail and head at intervals of approximately 3 seconds.




v.

Check the condition of the "Headlight System Malfunction Visit Your Dealer" warning message on the multi-information display.

Standard:
Condition Specified Condition
The headlight ECU sub-assembly LH has been replaced with a new one. Blinks 6 times at 2 Hz → Continuously blinks N* times at 2 Hz.
Replacement of the rear height control sensor sub-assembly LH, removal and reinstallation of the rear height control sensor sub-assembly LH, replacement of the suspension, etc. have been performed. Off → Continuously blinks N* times at 2 Hz.


HINT:
·

*: The number of times that "Headlight System Malfunction Visit Your Dealer" warning message blinks is determined by the number of times the low beam headlights are turned on and off.

·

If the "Headlight System Malfunction Visit Your Dealer" warning message is displayed on the multi-information display, the headlight ECU sub-assembly LH may be malfunctioning.

·

If initialization does not finish normally, restart the initialization procedure from step (i).




vi.

Check that initialization finishes normally and turn the power switch off.

HINT:

The warning message will blink in the pattern indicating that initialization has completed successfully continuously until the power switch is turned off.