Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM › 2017.09–2019.02
RM33C0E _57 Power Source / Network _065454 NETWORKING _0331186 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B2785  Communication Malfunction between ECUs Connected by LIN  


DESCRIPTION

If the certification ECU (smart key ECU assembly) detects a communication error with an ECU connected to the certification bus lines for 7 seconds or more, DTC B2785 will be stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
B2785 Communication Malfunction between ECUs Connected by LIN
·

Errors in LIN communication between ECUs or an open or short in communication lines.

·

The certification ECU (smart key ECU assembly) detects a communication error with an ECU connected to the certification bus lines for 7 seconds or more.


·

Certification ECU (smart key ECU assembly)

·

Steering lock ECU (steering lock actuator or upper bracket assembly)

·

Wire harness or connector



WIRING DIAGRAM

B486911E03
0.719,1.479 1.219,1.771 0.5,0.292 10 false K62 0.708,1.646 2.24,2.083 1.531,0.438 10 false Certification ECU (Smart Key ECU Assembly) 0.729,2.323 2.469,2.656 1.74,0.333 10 false : LIN Communication Line 4.354,1.469 5.656,1.781 1.302,0.313 10 false K65 4.344,1.635 7.021,2.083 2.677,0.448 10 false Steering Lock ECU (Steering Lock Actuator or Upper Bracket Assembly) 4.927,0.948 5.427,1.24 0.5,0.292 10 false LIN 4.76,0.792 5.26,1.083 0.5,0.292 10 false 5 2.323,0.792 2.823,1.083 0.5,0.292 10 false 13 2.021,0.969 2.521,1.26 0.5,0.292 10 false LIN

CAUTION / NOTICE / HINT

NOTICE:
·

Before performing the inspection, check that DTC B2786 or B278C is not output.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

·

When using the GTS with the power switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Before replacing the certification ECU (smart key ECU assembly) or steering lock ECU (steering lock actuator or upper bracket assembly), refer to Service Bulletin.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - EACH ECU)
a.

Disconnect the K62 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the K65 steering lock ECU (steering lock actuator or upper bracket assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K62-13 (LIN) - K65-5 (LIN) Always Below 1 Ω
K62-13 (LIN) or K65-5 (LIN) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK FOR DTC (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK FOR DTC (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
a.

Reconnect the K62 certification ECU (smart key ECU assembly) connector.


b.

Clear the DTCs.

Body Electrical > Entry&Start > Clear DTCs
50002 125

c.

Recheck for DTCs.

Body Electrical > Entry&Start > Trouble Codes
50001 125

Result:
Result Proceed to
DTC B2785 is output A
DTC B2785 is not output B



A

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

B

REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)