MALFUNCTION DESCRIPTION
The hybrid vehicle control ECU assembly monitors the motor generator control ECU (MG ECU).
The cause of this malfunction may be the following:
Motor generator control ECU (MG ECU) malfunction
The hybrid vehicle control ECU assembly monitors the motor generator control ECU (MG ECU) and stores this DTC when it detects a malfunction.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Warning Indicate |
|---|---|---|---|---|---|
| P0A1B94 | Drive Motor "A" Control Module Unexpected Operation | The motor generator control ECU (MG ECU) value received by the hybrid vehicle control ECU assembly exceeds the threshold for a certain period of time.
(1 trip detection logic) |
·
Inverter with converter assembly ·
Fusible link block assembly (IGCT) ·
IGCT relay |
Comes on | Master Warning Light:
Comes on |
After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Connect the GTS to the DLC3.
Turn the power switch on (IG) and turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the power switch off and wait for 2 minutes or more.
Turn the power switch on (IG) and turn the GTS on.
With power switch on (IG) and wait for 2 minutes or more.
If the vehicle has returned to normal, it can be driven after turning the power switch on (READY).
Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.
Check the DTC judgment result.
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
Check the connection of the negative (-) and positive (+) auxiliary battery terminals.
The terminals are connected securely and there is no contact problem.
If performing a reproduction test, turn the power switch on (IG) and shake the wire harnesses vertically and horizontally before checking for DTCs.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the installation condition of the ground wires TA.
The ground wires TA are securely installed.
If performing a reproduction test, turn the power switch on (IG) and shake the wire harnesses vertically and horizontally before checking for DTCs.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the cable from the positive (+) auxiliary battery terminal.
Check the fusible link block assembly (IGCT) for improper installation.
The fusible link block assembly is installed securely and there is no contact problem.
Disconnect the R117 fusible link block assembly connector.
| *1 | Fusible Link Block Assembly |
| *a | Component without harness connected
(Fusible Link Block Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| R117-1 - A-1 (Positive (+) auxiliary battery terminal) | Power switch off | Below 1 Ω |
Reconnect the R117 fusible link block assembly connector.
Reconnect the cable from the positive (+) auxiliary battery terminal.
Reconnect the cable from the negative (-) auxiliary battery terminal.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the IGCT relay for improper installation.
The relay is installed securely.
If performing a reproduction test, turn the power switch on (IG) and gently vibrate the IGCT relay with a finger before checking for DTCs.
| *A | for LHD |
| *B | for RHD |
| *1 | No. 6 Relay Block |
| *2 | IGCT Relay |
Remove the IGCT relay from the No. 6 relay block.
| *1 | IGCT Relay |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 - 5 | Auxiliary battery voltage not applied between terminals 1 and 2 | 10 kΩ or higher |
| Auxiliary battery voltage applied between terminals 1 and 2 | Below 1 Ω |
Install the IGCT relay.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
Check for DTCs.
Check the DTCs that were output when the vehicle was brought to the workshop.
| Result | Proceed to |
|---|---|
| P0A1B94 only is output. | A |
| DTCs except P0A1B94 are output. | B |
Turn the power switch off.
A
B
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT
Turn the power switch on (IG) and wait for 2 minutes or more.
Turn the power switch off.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
Check for DTCs.
| Result | Proceed to |
|---|---|
| No DTCs are output. | A |
| P0A1B94 only is output. | B |
| DTCs except P0A1B94 are output. | C |
Turn the power switch off.
A
B
C