Refer to DTC P062712.
Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>P062712
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P12D41D | Fuel Pump Control Circuit Current Out of Range | When the fuel pump control ECU operation duty ratio is 3 to 65%, overcurrent in the fuel pump circuit is detected for 3 seconds or more (1 trip detection logic). | ·
Short in fuel pump control ECU circuit ·
Fuel pump (for low pressure side) ·
Fuel pump (for low pressure side) locked ·
Foreign matter in the fuel ·
Fuel pump control ECU |
Does not come on | DTC stored | SAE Code: P12D4 |
| DTC No. | Data List |
|---|---|
| P12D41D | Fuel Pump Control Duty Ratio |
The fuel pump control ECU monitors the fuel pump drive circuit.
When a malfunction is detected in the fuel pump drive circuit, the diagnosis output circuit in the fuel pump control ECU modifies the operation signal sent by the ECM to indicate that there is a malfunction.
When the fuel pump control ECU operation duty ratio is 3 to 65% and overcurrent in the fuel pump circuit is detected for 3 seconds or more, the diagnosis output circuit in the fuel pump control ECU modifies the operation signal sent by the ECM to indicate that there is a malfunction and the ECM stores a DTC.
| Required Sensors/Components | Fuel pump control ECU |
| Frequency of Operation | Continuous |
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the power switch off and wait for at least 30 seconds.
Turn the power switch on (IG).
Turn the GTS on.
Put the engine in Inspection Mode (Maintenance Mode).
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE
Start the engine and wait 10 seconds or more [A].
Enter the following menus: Powertrain / Engine / Trouble Codes [B].
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input the DTC: P12D41D.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
If the judgment result is NORMAL, the system is normal.
If the judgment result is ABNORMAL, the system is malfunctioning.
If the judgment result is INCOMPLETE, run the engine at an engine speed of 2500 rpm or more for 10 seconds or more and check the DTC judgment result again.
Refer to DTC P062712.
Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>P062712
Vehicle Control History may be stored in the hybrid vehicle control ECU assembly if the engine is malfunctioning. Certain vehicle condition information is recorded when Vehicle Control History is stored. Reading the vehicle conditions recorded in both the freeze frame data and Vehicle Control History can be useful for troubleshooting.
(Select Powertrain in Health Check and then check the time stamp data.)
If any "Engine Malfunction" Vehicle Control History item has been stored in the hybrid vehicle control ECU assembly, make sure to clear it. However, as all Vehicle Control History items are cleared simultaneously, if any Vehicle Control History items other than "Engine Malfunction" are stored, make sure to perform any troubleshooting for them before clearing Vehicle Control History.
Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
| *a | Component without harness connected
(Fuel Pump Control ECU) |
- | - |
Remove the fuel pump control ECU.
Click hereEngine / Hybrid System>A25A-FXS (FUEL)>FUEL PUMP ECU>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| R17-2 (FPU) - R18-3 (GND) | Always | 2 kΩ or higher |
| R17-3 (FPV) - R18-3 (GND) | Always | 2 kΩ or higher |
| R17-4 (FPW) - R18-3 (GND) | Always | 2 kΩ or higher |
This procedure checks for an internal short of the fuel pump control ECU when its transistor is stuck on.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Fuel Pump Control ECU) |
Disconnect the R17 fuel pump control ECU connector.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Active Test / Fuel Pump Single Phase Energization.
| Tester Display |
|---|
| Fuel Pump Single Phase Energization |
Operate the fuel pump control ECU using the Active Test function and measure the voltage according to the value(s) in the table below.
| Tester Connection | GTS Operation | Specified Condition |
|---|---|---|
| R17-2 (FPU) - Body ground | U Phase | 4.4 to 8.4 V* |
| R17-3 (FPV) - Body ground | 8 to 15.5 V | |
| R17-4 (FPW) - Body ground | 8 to 15.5 V | |
| R17-3 (FPV) - Body ground | V Phase | 4.4 to 8.4 V* |
| R17-2 (FPU) - Body ground | 8 to 15.5 V | |
| R17-4 (FPW) - Body ground | 8 to 15.5 V | |
| R17-4 (FPW) - Body ground | W Phase | 4.4 to 8.4 V* |
| R17-2 (FPU) - Body ground | 8 to 15.5 V | |
| R17-3 (FPV) - Body ground | 8 to 15.5 V |
*: This Active Test limits the fuel pump control ECU output duty cycle to 50%. Therefore, the output voltage of the fuel pump control ECU will be approximately 50% of the power source voltage (+B terminal).
Before performing this inspection, check that the auxiliary battery voltage is between 11 and 14 V (not depleted).
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the fuel pump control ECU connector.
Disconnect the fuel pump (for low pressure side) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| R17-2 (FPU) or R43-3 (BLPU) - Other terminals | Always | 10 kΩ or higher |
| R17-3 (FPV) or R43-4 (BLPV) - Other terminals | Always | 10 kΩ or higher |
| R17-4 (FPW) or R43-2 (BLPW) - Other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the fuel pump (for low pressure side).
Click hereEngine / Hybrid System>A25A-FXS (FUEL)>FUEL PUMP (w/o Canister Pump Module)>REMOVAL
Perform "Inspection After Repair" after replacing the fuel pump (for low pressure side).
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Clear the DTCs.
Turn the power switch off and wait for at least 30 seconds.
| Proceed to |
|---|
| NEXT |
NEXT
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
DTCs are not output.
| Proceed to |
|---|
| NEXT |
NEXT