Home › Vehicle Interior › HEATING / AIR CONDITIONING › FRONT EVAPORATOR TEMPERATURE SENSOR › 2017.09–2018.08
RM33C0E _58 Vehicle Interior _065464 HEATING / AIR CONDITIONING _0331717 FRONT EVAPORATOR TEMPERATURE SENSOR A

HEATING / AIR CONDITIONING  FRONT EVAPORATOR TEMPERATURE SENSOR  INSTALLATION  


PROCEDURE

Hide 88625 1.INSTALL NO. 1 COOLER THERMISTOR

a.

for LHD (for 3 Zone Type) or RHD:

i.
E369185C02
2.563,0.781 2.802,0.563 false 1.635,0.385 2.083,0.75 false 2.917,2.833 3.177,1.771 true 2.448,2.833 3.01,1.771 true 2.344,2.833 2.656,2.99 0.313,0.156 10 false *a 2.813,2.844 3.125,3 0.313,0.156 10 false *b 1.479,0.26 1.792,0.417 0.313,0.156 10 false a 2.833,0.427 3.146,0.583 0.313,0.156 10 false b 0.198,1.99 0.51,2.146 0.313,0.156 10 false A 1.25,2.958 1.563,3.115 0.313,0.156 10 false B 1.875,3.188 2.188,3.344 0.313,0.156 10 false C 2.25,0.24 2.563,0.396 0.313,0.156 10 false X
*a Securing Part
*b Sensor Part


Install the No. 1 cooler thermistor as shown in the illustration.

Installation Position:
Part Length
A 50.0 mm (1.97 in.)
B 87.9 mm (3.46 in.)
C 188.3 mm (7.41 in.)


NOTICE:
·

Be sure to insert the No. 1 cooler thermistor only once because reinserting it into the same position will not allow it to be firmly secured.

·

When reusing the No. 1 cooler evaporator sub-assembly, insert the No. 1 cooler thermistor one row next to the one that has been used previously (X in the illustration).

·

After inserting the No. 1 cooler thermistor, do not apply excessive force to the wire.

·

Directly insert the No. 1 cooler thermistor until the edge of the plastic case "a" comes into contact with the No. 1 cooler evaporator sub-assembly "b".





b.

for LHD (except 3 Zone Type):

i.
E361957C01
2.177,1.01 2.521,0.5 false 1.677,1.01 1.448,0.479 false 1.948,2.75 2.5,4.25 true 2.167,2.75 2.719,4.25 true 2.417,4.25 2.729,4.406 0.313,0.156 10 false *a 2.667,4.25 2.979,4.406 0.313,0.156 10 false *b 1.333,0.344 1.646,0.5 0.313,0.156 10 false a 2.552,0.365 2.865,0.521 0.313,0.156 10 false b 1.583,4.333 1.896,4.49 0.313,0.156 10 false B 0.271,3.083 0.583,3.24 0.313,0.156 10 false A 1.844,0.427 2.156,0.583 0.313,0.156 10 false X
*a Securing Part
*b Sensor Part


Install the No. 1 cooler thermistor as shown in the illustration.

Installation Position:
Part Length
A 50.0 mm (1.97 in.)
B 61.1 mm (2.41 in.)


NOTICE:
·

Be sure to insert the No. 1 cooler thermistor only once because reinserting it into the same position will not allow it to be firmly secured.

·

When reusing the No. 1 cooler evaporator sub-assembly, insert the No. 1 cooler thermistor one row next to the one that has been used previously (X in the illustration).

·

After inserting the No. 1 cooler thermistor, do not apply excessive force to the wire.

·

Directly insert the No. 1 cooler thermistor until the edge of the plastic case "a" comes into contact with the No. 1 cooler evaporator sub-assembly "b".





Hide 88501 2.INSTALL NO. 1 COOLER EVAPORATOR SUB-ASSEMBLY

Hide 88515 3.INSTALL COOLER EXPANSION VALVE

Hide 87107A 5.INSTALL HEATER RADIATOR UNIT SUB-ASSEMBLY

Hide 87050E 8.INSTALL NO. 3 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY (for 3 Zone Type)

Hide 87050C 9.INSTALL NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY

Hide 82210K 10.INSTALL AIR CONDITIONING HARNESS ASSEMBLY

Hide 87130D 11.INSTALL BLOWER ASSEMBLY