Home › Vehicle Interior › INTERIOR PANELS / TRIM › REAR SUNSHADE SYSTEM
RM33C0E _58 Vehicle Interior _065466 INTERIOR PANELS / TRIM _0331728 REAR SUNSHADE SYSTEM J

INTERIOR PANELS / TRIM  REAR SUNSHADE SYSTEM  Rear Sunshade does not Operate with Rear Sunshade Switch  


DESCRIPTION

The rear window shade assembly operates according to operation signals from the combination meter assembly or rear sunshade switch (cooler control switch assembly)*.

*: w/ Cooler Control Switch Assembly


WIRING DIAGRAM

B487734E04
2.094,0.604 2.25,0.802 0.156,0.198 10 false B 2.083,1.188 2.396,1.385 0.313,0.198 10 false IG 1.885,2.49 2.344,2.688 0.458,0.198 10 false RSW 1.99,4.51 2.302,4.708 0.313,0.198 10 false SW 2.125,5.208 2.281,5.406 0.156,0.198 10 false E 0.406,2.667 0.979,3.021 0.573,0.354 10 false Motor 2.344,0.49 2.5,0.688 0.156,0.198 10 false 8 2.354,1.083 2.51,1.281 0.156,0.198 10 false 7 2.365,2.49 2.521,2.688 0.156,0.198 10 false 4 2.354,4.51 2.51,4.708 0.156,0.198 10 false 5 2.354,5.083 2.51,5.281 0.156,0.198 10 false 1 4.125,2.042 4.438,2.24 0.313,0.198 10 false 10 4.198,2.49 4.354,2.688 0.156,0.198 10 false 4 3.615,0.76 5.302,0.958 1.688,0.198 10 false ECU-B NO. 2 3.625,1.365 5.615,1.563 1.99,0.198 10 false ECU-IG1 NO. 4 5.167,0.604 7,0.802 1.833,0.198 10 false from Auxiliary Battery 5.167,1.188 6.99,1.813 1.823,0.625 10 false from IG1-NO. 1 Relay 4.427,2.146 4.885,2.344 0.458,0.198 10 false +IG 4.417,2.49 4.875,2.688 0.458,0.198 10 false ECU 5.625,2.833 6.083,3.031 0.458,0.198 10 false GND 6.052,2.833 6.365,3.031 0.313,0.198 10 false 16 4.25,3.344 4.708,3.542 0.458,0.198 10 false Z1 4.26,3.5 6.156,4.542 1.896,1.042 10 false Rear Sunshade Switch (Cooler Control Switch Assembly)* 4.104,4.51 4.417,4.708 0.313,0.198 10 false 22 4.396,4.5 4.854,4.698 0.458,0.198 10 false ECU 4.385,5.177 4.844,5.375 0.458,0.198 10 false K21 4.385,5.323 6.542,5.708 2.156,0.385 10 false Combination Meter Assembly 0.302,5.563 0.76,5.76 0.458,0.198 10 false R64 0.302,5.719 2.302,6.094 2,0.375 10 false Rear Window Shade Assembly 5.365,4.698 5.677,4.896 0.313,0.198 10 false IC 5.365,2.521 5.677,2.719 0.313,0.198 10 false IC 1.354,2.094 1.74,2.302 0.385,0.208 10 false 12 V 1.365,4.104 1.75,4.313 0.385,0.208 10 false 12 V 1.01,3.563 1.323,3.76 0.313,0.198 10 false IC 4.49,6.313 6.969,6.625 2.479,0.313 10 false *: w/ Cooler Control Switch Assembly

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK REAR SUNSHADE OPERATION
a.

Result:
Result Proceed to
The rear sunshade does not operate with combination meter assembly operation. A
The rear sunshade does not operate with rear sunshade switch (cooler control switch assembly) operation. (w/ Cooler Control Switch Assembly) B
The rear sunshade does not operate with combination meter assembly and rear sunshade switch (cooler control switch assembly) operation. (w/ Cooler Control Switch Assembly) C



A

2.CHECK REAR WINDOW SHADE ASSEMBLY

B

4.CHECK REAR WINDOW SHADE ASSEMBLY

C

7.CHECK HARNESS AND CONNECTOR (POWER SOURCE AND BODY GROUND)
2.CHECK REAR WINDOW SHADE ASSEMBLY
a.
E284677C64
1.5,0.167 1.917,0.417 0.417,0.25 2.75,1.719 2.563,1.719 2.563,1.719 2.563,1.125 true 0.198,0.156 0.51,0.313 0.313,0.156 10 false *a 1.583,0.208 1.854,0.406 0.271,0.198 10 false K21 2.813,1.635 3.219,1.833 0.406,0.198 10 false ECU
*a Component with harness connected
(Combination Meter Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
K21-22 (ECU) - Body ground Rear window shade assembly not operating 5.5 V or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

3.CHECK HARNESS AND CONNECTOR (REAR WINDOW SHADE ASSEMBLY - COMBINATION METER ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (REAR WINDOW SHADE ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Disconnect the R64 rear window shade assembly connector.


b.

Disconnect the K21 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R64-5 (SW) - K21-22 (ECU) Always Below 1 Ω
R64-5 (SW) or K21-22 (ECU) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE REAR WINDOW SHADE ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK REAR WINDOW SHADE ASSEMBLY
a.
B487774C01
1.5,0.188 1.896,0.406 0.396,0.219 0.99,1.74 1.219,1.74 1.219,1.74 1.75,1.021 true 0.125,0.188 0.448,0.344 0.323,0.156 10 false *a 1.635,0.219 1.948,0.375 0.313,0.156 10 false Z1 0.677,1.656 1.083,1.885 0.406,0.229 10 false ECU
*a Component with harness connected
(Rear Sunshade Switch (Cooler Control Switch Assembly))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Z1-4 (ECU) - Body ground Rear window shade assembly not operating 5.5 V or higher



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (POWER SOURCE AND BODY GROUND)

NG

6.CHECK HARNESS AND CONNECTOR (REAR WINDOW SHADE ASSEMBLY - REAR SUNSHADE SWITCH (COOLER CONTROL SWITCH ASSEMBLY))
5.CHECK HARNESS AND CONNECTOR (POWER SOURCE AND BODY GROUND)
a.

Disconnect the Z1 rear sunshade switch (cooler control switch assembly) connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Z1-10 (+IG) - Body ground Power switch off Below 1 V
Z1-10 (+IG) - Body ground Power switch on (IG) 11 to 14 V


Standard Resistance:
Tester Connection Condition Specified Condition
Z1-16 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE REAR SUNSHADE SWITCH (COOLER CONTROL SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (REAR WINDOW SHADE ASSEMBLY - REAR SUNSHADE SWITCH (COOLER CONTROL SWITCH ASSEMBLY))
a.

Disconnect the R64 rear window shade assembly connector.


b.

Disconnect the Z1 rear sunshade switch (cooler control switch assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R64-4 (RSW) - Z1-4 (ECU) Always Below 1 Ω
R64-4 (RSW) or Z1-4 (ECU) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE REAR WINDOW SHADE ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (POWER SOURCE AND BODY GROUND)
a.

Disconnect the R64 rear window shade assembly connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
R64-8 (B) - Body ground Power switch off 11 to 14 V
R64-7 (IG) - Body ground Power switch off Below 1 V
R64-7 (IG) - Body ground Power switch on (IG) 11 to 14 V


Standard Resistance:
Tester Connection Condition Specified Condition
R64-1 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE REAR WINDOW SHADE ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR