Home › Vehicle Interior › INTERIOR PANELS / TRIM › REAR SUNSHADE SYSTEM
RM33C0E _58 Vehicle Interior _065466 INTERIOR PANELS / TRIM _0331728 REAR SUNSHADE SYSTEM J

INTERIOR PANELS / TRIM  REAR SUNSHADE SYSTEM  Rear Sunshade Shift-linked Function does not Operate when Shift Lever is Moved to R Position  


DESCRIPTION

When the power switch on (IG) and the shift lever is moved to R, the shift position sensors send a reverse signal to the hybrid vehicle control ECU assembly. Then, the hybrid vehicle control ECU assembly sends this signal to the main body ECU (multiplex network body ECU) via CAN communication. When the rear sunshade relay receives this signal with the rear sunshade raised, the rear sunshade is lowered.

WIRING DIAGRAM

B489118E02
0.375,1.677 1.792,2.375 1.417,0.698 10 false Hybrid Vehicle Control ECU Assembly 0.604,2.438 2.49,2.74 1.885,0.302 10 false : CAN Communication Line 2.865,0.917 3.323,1.115 0.458,0.198 10 false IC 6.375,0.917 6.833,1.115 0.458,0.198 10 false IC 5.917,0.344 6.375,0.542 0.458,0.198 10 false 12 V 5.406,0.719 5.865,0.917 0.458,0.198 10 false REV 5.167,0.719 5.625,0.917 0.458,0.198 10 false 3 3.677,0.719 4.135,0.917 0.458,0.198 10 false REV 4.094,0.719 4.552,0.917 0.458,0.198 10 false 6 2.563,1.698 3.021,1.896 0.458,0.198 10 false K51 2.563,1.865 4.198,2.25 1.635,0.385 10 false Main Body ECU (Multiplex Network Body ECU) 5.385,1.698 5.844,1.896 0.458,0.198 10 false R64 5.385,1.865 6.656,2.25 1.271,0.385 10 false Rear Window Shade Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

The rear sunshade system uses the CAN communication system. First, confirm that there are no malfunctions in the CAN communication system. Refer to How to Proceed with Troubleshooting procedure.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>REAR SUNSHADE SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

The shift-linked operation of the rear sunshade system operates only when the customize setting "R-pos to Rear Sun Shade COM" is set to "ON".

Click hereVehicle Interior>INTERIOR PANELS / TRIM>REAR SUNSHADE SYSTEM>CUSTOMIZE PARAMETERS

·

If the main body ECU (multiplex network body ECU) is replaced, refer to Service Bulletin.



PROCEDURE

1.READ VALUE USING GTS (SHIFT POSITION SENSOR (R))
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Hybrid Control / Data List.


e.

Read the Data List according to the display on the GTS.

Powertrain > Hybrid Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Shift Position Sensor (R) Shift lever position sensor OFF or ON OFF: Shift lever not in R
OK: Shift lever in R
-
Powertrain > Hybrid Control > Data List
Tester Display
Shift Position Sensor (R)
50003 397 405
OK:

The GTS display changes according to the shift position selected by using the shift lever.



Result:
Proceed to
OK
NG



OK

2.PERFORM ACTIVE TEST USING GTS (REVERSE GEAR SIGNAL)

NG

2.PERFORM ACTIVE TEST USING GTS (REVERSE GEAR SIGNAL)
a.

Enter the following menus: Body Electrical / Main Body / Active Test.


b.

Perform the Active Test according to the display on the GTS.

HINT:

Make sure that the rear window shade assembly is raised before performing the Active Test.


Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Reverse Gear Signal Reverse signal OFF/ON -
Body Electrical > Main Body > Active Test
Tester Display
Reverse Gear Signal
50004 123 24
OK:

The rear window shade assembly is lowered.



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

3.CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
3.CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
R64-3 (REV) - Body ground Power switch on (IG), shift lever in any position other than R → R 11 to 14 V → Below 1 V



Result:
Proceed to
OK
NG



OK

REPLACE REAR WINDOW SHADE ASSEMBLY

NG

4.CHECK HARNESS AND CONNECTOR (REAR WINDOW SHADE ASSEMBLY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
4.CHECK HARNESS AND CONNECTOR (REAR WINDOW SHADE ASSEMBLY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

Disconnect the K51 main body ECU (multiplex network body ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K51-6 (REV) - R64-3 (REV) Always Below 1 Ω
K51-6 (REV) or R64-3 (REV) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR