Home › Engine / Hybrid System › CRUISE CONTROL › FORWARD RECOGNITION CAMERA SYSTEM › 2017.09–2021.02
RM33C0E _51 Engine / Hybrid System _065434 CRUISE CONTROL _0331759 FORWARD RECOGNITION CAMERA SYSTEM C

CRUISE CONTROL  FORWARD RECOGNITION CAMERA SYSTEM  C1AAE  Heater Circuit  


DESCRIPTION

The forward recognition camera controls the flow of current to the camera heater (forward recognition hood).

If the forward recognition camera detects a malfunction in the camera heater (forward recognition hood) circuit, DTC C1AAE is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1AAE Heater Circuit
Either of the following conditions is met after 3 seconds have elapsed since the power switch was turned on (IG):
·

While a camera heater (forward recognition hood) ON request is being sent, short to +B detected in the camera heater (forward recognition hood) circuit for 5 seconds or more.

·

While a camera heater (forward recognition hood) ON request is not being sent, open or short to ground detected in the camera heater (forward recognition hood) circuit for 5 seconds or more.


·

Camera heater (Forward recognition hood)

·

Forward recognition camera

·

Harness or connector



DTC Detection Conditions
Vehicle Condition Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition Power switch on (IG) ○ ○
Malfunction Status While a camera heater (forward recognition hood) ON request is being sent, short to +B detected in the camera heater (forward recognition hood) circuit. ○ -
While a camera heater (forward recognition hood) ON request is not being sent, open or short to ground detected in the camera heater (forward recognition hood) circuit. - ○
Detection Time 5 seconds or more 5 seconds or more
Number of Trips 1 trip 1 trip

HINT:

If any of the detection patterns above are met, a DTC is output.


WIRING DIAGRAM

A407893E02
0.302,0.448 2.448,0.646 2.146,0.198 10 false from IG1-NO. 1 Relay 2.229,0.604 4.063,0.802 1.833,0.198 10 false ECU-IG1 NO. 3 4,2.094 6.938,2.344 2.938,0.25 10 false Camera Heater (Forward Recognition Hood) 0.792,2.385 3.24,2.583 2.448,0.198 10 false Forward Recognition Camera 0.792,2.229 1.104,2.427 0.313,0.198 10 false V6 4.01,1.917 4.469,2.115 0.458,0.198 10 false V16 2.01,1.802 2.469,2 0.458,0.198 10 false HTR 2.354,1.698 2.51,1.896 0.156,0.198 10 false 1 3.656,0.844 3.813,1.042 0.156,0.198 10 false 2 3.844,0.844 4.302,1.042 0.458,0.198 10 false HTR 3.656,0.365 3.813,0.563 0.156,0.198 10 false 1 3.844,0.365 4.302,0.563 0.458,0.198 10 false IG1 5.563,1.365 6.635,1.563 1.073,0.198 10 false Heater Hood 4.458,0.75 5.073,0.958 0.615,0.208 10 false Diode 4.24,0.365 4.396,0.563 0.156,0.198 10 false 1 4.927,0.365 5.083,0.563 0.156,0.198 10 false 2

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle. As a result, a DTC may be stored.

·

If the forward recognition camera has been replaced with a new one, be sure to perform forward recognition camera adjustment.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (SEQUENTIAL RECOGNITION)



PROCEDURE

1.CHECK FOR DTCs (FORWARD RECOGNITION CAMERA SYSTEM)
a.

Clear the DTCs.

Chassis > Front Recognition Camera > Clear DTCs
50002 386

b.

Perform the following procedure.

HINT:

If the following procedure is not performed, the previously output DTC cannot be detected.

1.

Turn the power switch on (IG) and wait 8 seconds or more.




c.

Check for DTCs.

Chassis > Front Recognition Camera > Trouble Codes
50001 386

Result:
Result Proceed to
DTC C1AAE is not output A
DTC C1AAE is output B



A

B

2.INSPECT CAMERA HEATER (FORWARD RECOGNITION HOOD)
2.INSPECT CAMERA HEATER (FORWARD RECOGNITION HOOD)
a.

Turn the power switch off.


b.

Disconnect the V16 camera heater (forward recognition hood) connector.

A407894C02
5.219,2.177 5.625,2.417 0.406,0.24 1.646,0.177 1.948,0.375 0.302,0.198 4.094,1.229 4.219,0.542 4.219,0.542 4.469,0.542 false 2.073,2.906 2.177,3.313 2.177,3.313 2.427,3.313 false 5.51,2.875 5.927,2.729 true 4.865,2.76 5.271,2.875 true 2.49,3.25 2.802,3.406 0.313,0.156 10 false *1 4.51,0.479 4.823,0.635 0.313,0.156 10 false *2 4.302,2.188 4.615,2.344 0.313,0.156 10 false *a 5.302,2.229 5.625,2.375 0.323,0.146 10 false V16 5.99,2.656 6.448,2.854 0.458,0.198 10 false IG1 4.563,2.698 5.021,2.896 0.458,0.198 10 false HTR 1.75,0.198 1.948,0.385 0.198,0.188 10 false A
*1 Camera Heater (Forward Recognition Hood) *2 Diode
*a Component without harness connected - -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V16-2 (HTR) - A-2 Always Power switch off 36.1 to 39.9 Ω
V16-1 (IG1) - A-1 Always Power switch off Below 1 Ω
A-1 - A-2
·

Positive (+) tester probe → A-1

·

Negative (-) tester probe → A-2


HINT:

If the tester probes are connected to the wrong terminals, due to the existence of the diode, current will not flow and the result will be the same as for an open circuit.


Power switch off Below 1 Ω



d.

Connect the V16 camera heater (forward recognition hood) connector.


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE VOLTAGE)

NG

REPLACE CAMERA HEATER (FORWARD RECOGNITION HOOD)

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE VOLTAGE)
a.
C367313C13
1.5,0.25 1.927,0.5 0.427,0.25 1.167,1.667 1.333,1.667 1.333,1.667 1.615,1.313 true 1.594,0.292 1.99,0.49 0.396,0.198 10 false V16 0.917,1.594 1.229,1.792 0.313,0.198 10 false IG1 0.115,0.115 0.427,0.271 0.313,0.156 10 false *a
*a Front view of wire harness connector
(to Camera Heater (Forward Recognition Hood))


Disconnect the V16 camera heater (forward recognition hood) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
V16-1 (IG1) - Body ground Power switch on (IG) 11 to 14 V
Power switch off Below 1.5 V



c.

Connect the V16 camera heater (forward recognition hood) connector.


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (CAMERA HEATER (FORWARD RECOGNITION HOOD) - FORWARD RECOGNITION CAMERA)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE VOLTAGE)

4.CHECK HARNESS AND CONNECTOR (CAMERA HEATER (FORWARD RECOGNITION HOOD) - FORWARD RECOGNITION CAMERA)
a.

Disconnect the V16 camera heater (forward recognition hood) connector.


b.

Disconnect the V6 forward recognition camera connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V16-2 (HTR) - V6-1 (HTR) Always Below 1 Ω
V16-2 (HTR) or V6-1 (HTR) - Body ground Always 10 kΩ or higher



d.

Connect the V6 forward recognition camera connector.


e.

Connect the V16 camera heater (forward recognition hood) connector.


Result:
Proceed to
OK
NG



OK

REPLACE FORWARD RECOGNITION CAMERA

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (CAMERA HEATER (FORWARD RECOGNITION HOOD) - FORWARD RECOGNITION CAMERA)