Home › Engine / Hybrid System › CRUISE CONTROL › LANE DEPARTURE ALERT SYSTEM (w/ Steering Control) › 2017.09–2021.02
RM33C0E _51 Engine / Hybrid System _065434 CRUISE CONTROL _0331760 LANE DEPARTURE ALERT SYSTEM(w/ Steering Control) C

CRUISE CONTROL  LANE DEPARTURE ALERT SYSTEM(w/ Steering Control)  C1AA1  FCM Destination Information Unmatched  


DESCRIPTION

When the forward recognition camera is replaced with a new one, the new forward recognition camera attempts to store vehicle information received from the main body ECU (multiplex network body ECU) and hybrid vehicle control ECU assembly. If the vehicle information stored in the forward recognition camera is different from that stored in the main body ECU (multiplex network body ECU) or hybrid vehicle control ECU assembly, DTC C1AA1 is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1AA1 FCM Destination Information Unmatched After the power switch is turned on (IG) for 3 seconds or more, vehicle information stored in the forward recognition camera and that received from the main body ECU (multiplex network body ECU) or hybrid vehicle control ECU assembly do not match for 5 seconds or more.
·

CAN communication system

·

Forward recognition camera

·

Main body ECU (Multiplex network body ECU)

·

Hybrid vehicle control ECU assembly



CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.

·

When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle. As a result, a DTC may be stored.

·

If the forward recognition camera has been replaced with a new one, be sure to perform forward recognition camera adjustment.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (SEQUENTIAL RECOGNITION)



HINT:

This DTC is stored when the vehicle information stored in the forward recognition camera and that stored in the main body ECU (multiplex network body ECU) or hybrid vehicle control ECU assembly do not match. If the forward recognition camera, main body ECU (multiplex network body ECU) or hybrid vehicle control ECU assembly has been replaced, check if a forward recognition camera, main body ECU (multiplex network body ECU) or hybrid vehicle control ECU assembly from another vehicle was used.


PROCEDURE

1.CHECK FOR DTCs (LANE DEPARTURE ALERT SYSTEM)
HINT:

When DTC C1AA1 is stored, DTC C1AAC may be stored at the same time.


a.

Check for DTCs.

Chassis > LKA/LDA > Trouble Codes
50001 355

Result:
Result Proceed to
DTC C1AAC is not output A
DTC C1AAC is output B



A

2.CHECK FOR DTCs (CAN COMMUNICATION DTC OUTPUT)

B

2.CHECK FOR DTCs (CAN COMMUNICATION DTC OUTPUT)
HINT:

The forward recognition camera communicates with the main body ECU (multiplex network body ECU) via CAN communication. Confirm that the CAN communication system is functioning normally before proceeding.


a.

Check for DTCs.

Chassis > LKA/LDA > Trouble Codes
50001 355

Result:
Result Proceed to
DTC U0142 is not output A
DTC U0142 is output B



A

3.CHECK FOR DTCs (LANE DEPARTURE ALERT SYSTEM)

B

3.CHECK FOR DTCs (LANE DEPARTURE ALERT SYSTEM)
a.

Clear the DTCs.

Chassis > LKA/LDA > Clear DTCs
50002 355

b.

Perform the following procedure.

HINT:

If the following procedure is not performed, the previously output DTC cannot be detected.

1.

Turn the power switch on (IG) and wait 8 seconds or more.




c.

Check for DTCs.

Chassis > LKA/LDA > Trouble Codes
50001 355

Result:
Result Proceed to
DTC C1AA1 is not output A
DTC C1AA1 is output B



A

B

4.REPLACE FORWARD RECOGNITION CAMERA
4.REPLACE FORWARD RECOGNITION CAMERA
a.

Replace the forward recognition camera.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>REMOVAL


b.

Perform forward recognition camera adjustment.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (SEQUENTIAL RECOGNITION)


Result:
Proceed to
NEXT



NEXT

5.CHECK FOR DTCs (LANE DEPARTURE ALERT SYSTEM)
5.CHECK FOR DTCs (LANE DEPARTURE ALERT SYSTEM)
a.

Clear the DTCs.

Chassis > LKA/LDA > Clear DTCs
50002 355

b.

Perform the following procedure.

HINT:

If the following procedure is not performed, the previously output DTC cannot be detected.

1.

Turn the power switch on (IG) and wait 8 seconds or more.




c.

Check for DTCs.

Chassis > LKA/LDA > Trouble Codes
50001 355

Result:
Result Proceed to
DTC C1AA1 is not output A
DTC C1AA1 is output B



A

END (FORWARD RECOGNITION CAMERA WAS DEFECTIVE)

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)