Home › Steering › STEERING COLUMN › POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM
RM33C0E _55 Steering _065448 STEERING COLUMN _0331813 POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM J

STEERING COLUMN  POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM  IG Power Source Circuit  


DESCRIPTION

When the power switch is turned on (IG), the IG power source circuit supplies positive (+) voltage to the multiplex tilt and telescopic ECU.

WIRING DIAGRAM

C244378E47
3.708,0.823 4.833,1.125 1.125,0.302 10 false ECU-IG1 NO. 4 0.625,0.635 1.646,0.896 1.021,0.26 10 false from IG Circuit 5.792,0.635 6.667,0.969 0.875,0.333 10 false IG 5.781,2.333 6.26,2.615 0.479,0.281 10 false GND2 5.51,0.542 5.698,0.729 0.188,0.188 10 false 10 5.594,2.24 5.844,2.417 0.25,0.177 10 false 8 5.781,1.417 6.26,1.698 0.479,0.281 10 false GND 5.594,1.323 5.844,1.5 0.25,0.177 10 false 1 5.604,2.865 6.125,3.094 0.521,0.229 10 false K72 5.604,3.031 6.688,3.469 1.083,0.438 10 false Multiplex Tilt and Telescopic ECU

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - AUXILIARY BATTERY)
a.
C317591C89
1.51,0.333 1.927,0.583 0.417,0.25 1.094,1.604 1.188,1.229 true 1.01,1.635 1.49,1.833 0.479,0.198 10 false IG 1.604,0.375 2.083,0.573 0.479,0.198 10 false K72 0.115,0.083 0.573,0.281 0.458,0.198 10 false *a
*a Front view of wire harness connector
(to Multiplex Tilt and Telescopic ECU)


Disconnect the K72 multiplex tilt and telescopic ECU connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
K72-10 (IG) - Body ground Power switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - BODY GROUND)
a.
C317591C85
1.51,0.333 1.927,0.583 0.417,0.25 0.771,0.979 0.656,0.583 true 0.854,1.604 0.792,1.24 true 0.49,0.396 0.948,0.594 0.458,0.198 10 false GND 0.719,1.646 1.198,1.844 0.479,0.198 10 false GND2 1.594,0.375 2.073,0.573 0.479,0.198 10 false K72 0.115,0.083 0.573,0.281 0.458,0.198 10 false *a
*a Front view of wire harness connector
(to Multiplex Tilt and Telescopic ECU)


Disconnect the K72 multiplex tilt and telescopic ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K72-1 (GND) - Body ground Always Below 1 Ω
K72-8 (GND2) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MULTIPLEX TILT AND TELESCOPIC ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR