Home › Steering › STEERING COLUMN › POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM › 2017.09–2020.08
RM33C0E _55 Steering _065448 STEERING COLUMN _0331813 POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM U

STEERING COLUMN  POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM  DATA LIST / ACTIVE TEST  


READ DATA LIST


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Turn the power switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the power switch on (IG).


d.

Turn the GTS on.


e.

Enter the following menus: Body Electrical / Tilt & Telescopic / Data List.


f.

According to the display on the GTS, read the Data List.

Body Electrical > Tilt&Telescopic > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Total Distance Traveled Driving distance Min.: 0
Max.: 999999
- -
Total Distance Traveled - Unit Driving distance unit km or mile - -
Tilt Up Limit Uppermost tilt position No Memory or Memory No Memory: Position not memorized
Memory: Position memorized
-
Tilt Down Limit Lowermost tilt position No Memory or Memory No Memory: Position not memorized
Memory: Position memorized
-
Telescopic Short Limit Shortest telescopic position No Memory or Memory No Memory: Position not memorized
Memory: Position memorized
-
Telescopic Long Limit Longest telescopic position No Memory or Memory No Memory: Position not memorized
Memory: Position memorized
-
Tilt&Telescopic Memory 1 (Driver1 Tilt&Telescopic Memory 1) Tilt and telescopic memory position 1 No Memory or Memory No Memory: Position not memorized
Memory: Position memorized
For Tilt&Telescopic Memory 1
Tilt&Telescopic Memory 2 (Driver1 Tilt&Telescopic Memory 2) Tilt and telescopic memory position 2 No Memory or Memory No Memory: Position not memorized
Memory: Position memorized
For Tilt&Telescopic Memory 2
Tilt&Telescopic Memory 3 (Driver1 Tilt&Telescopic Memory 3) Tilt and telescopic memory position 3 No Memory or Memory No Memory: Position not memorized
Memory: Position memorized
For Tilt&Telescopic Memory 3
Driver Information Memory 1 (Driver1 Tilt&Telescopic Memory Last) Driver Information Memory 1 No Memory or Memory No Memory: Position not memorized
Memory: Position memorized
For Driver Information Memory 1
Driver Information Memory 2 (Driver2 Tilt&Telescopic Memory 1) Driver Information Memory 2 No Memory or Memory No Memory: Position not memorized
Memory: Position memorized
For Driver Information Memory 2
Driver Information Memory 3 (Driver2 Tilt&Telescopic Memory 2) Driver Information Memory 3 No Memory or Memory No Memory: Position not memorized
Memory: Position memorized
For Driver Information Memory 3
Ignition Switch (CAN) Communication state of power switch OFF or ON ON: Communication normal
OFF: Communication interrupted
-
Handle Position Steering wheel position signal Away or Return Away: Steering wheel in away position
Return: Steering wheel in return position
-
Ignition Switch Input state of power switch OFF or ON ON: Input signal normal
OFF: Input signal interrupted
-
Tilt Manual Switch Up Input state of tilt up switch OFF or ON - -
Tilt Manual Switch Down Input state of tilt down switch OFF or ON - -
Telescopic Manual Switch Short Input state of telescopic contract switch OFF or ON - -
Telescopic Manual Switch Long Input state of telescopic extend switch OFF or ON - -
Tilt&Telescopic Manual Switch Voltage Voltage data of tilt and telescopic switch Min.: 0.000 V
Max.: 4.998 V
Neutral position: Below 0.20 V
Tilt up: 1.67 to 2.13 V
Tilt down: 0.54 to 0.74 V
Telescopic contract: 1.08 to 1.40 V
Telescopic extend: 2.22 to 2.77 V
-
ECU Power Source Voltage Voltage data of power supply Min.: 0.000 V
Max.: 19.992 V
11.00 to 14.00 V -
Tilt Position Current tilt position data Min.: 0
Max.: 65535
28627 to 36864 -
Telescopic Position Current telescopic position data Min.: 0
Max.: 65535
28627 to 36864 -
Tilt Return Memory Position Memorized tilt return position data Min.: 0
Max.: 65535
28627 to 36864 -
Telescopic Return Memory Position Memorized telescopic return position data Min.: 0
Max.: 65535
28627 to 36864 -
Tilt Up Limit Position Uppermost tilt position data Min.: 0
Max.: 65535
28627 to 36864 -
Tilt Down Limit Position Lowermost tilt position data Min.: 0
Max.: 65535
28627 to 36864 -
Telescopic Short Limit Position Shortest telescopic position data Min.: 0
Max.: 65535
28627 to 36864 -
Telescopic Long Limit Position Longest telescopic position data Min.: 0
Max.: 65535
28627 to 36864 -
Tilt Memory Position 1 (Driver1 Tilt Memory Position 1) Tilt data of memory position 1 Min.: 0
Max.: 65535
28627 to 36864 For Tilt Memory Position 1
Telescopic Memory Position 1 (Driver1 Telescopic Memory Position 1) Telescopic data of memory position 1 Min.: 0
Max.: 65535
28627 to 36864 For Telescopic Memory Position 1
Tilt Memory Position 2 (Driver1 Tilt Memory Position 2) Tilt data of memory position 2 Min.: 0
Max.: 65535
28627 to 36864 For Tilt Memory Position 2
Telescopic Memory Position 2 (Driver1 Telescopic Memory Position 2) Telescopic data of memory position 2 Min.: 0
Max.: 65535
28627 to 36864 For Telescopic Memory Position 2
Tilt Memory Position 3 (Driver1 Tilt Memory Position 3) Tilt data of memory position 3 Min.: 0
Max.: 65535
28627 to 36864 For Tilt Memory Position 3
Telescopic Memory Position 3 (Driver1 Telescopic Memory Position 3) Telescopic data of memory position 3 Min.: 0
Max.: 65535
28627 to 36864 For Telescopic Memory Position 3
Vehicle Speed Vehicle speed data Min.: 0 km/h (0 mph)
Max.: 255 km/h (158 mph)
Actual vehicle speed -
Driver Tilt Memory Position 1 (Driver1 Tilt Memory Position Last) Driver tilt memory position 1 Min.: 0
Max.: 65535
28627 to 36864 For Driver Tilt Memory Position 1
Driver Telescopic Memory Position 1 (Driver1 Telescopic Memory Position Last) Driver telescopic memory position 1 Min.: 0
Max.: 65535
28627 to 36864 For Driver Telescopic Memory Position 1
Driver Tilt Memory Position 2 (Driver2 Tilt Memory Position 1) Driver tilt memory position 2 Min.: 0
Max.: 65535
28627 to 36864 For Driver Tilt Memory Position 2
Driver Telescopic Memory Position 2 (Driver2 Telescopic Memory Position 1) Driver telescopic memory position 2 Min.: 0
Max.: 65535
28627 to 36864 For Driver Telescopic Memory Position 2
Driver Tilt Memory Position 3 (Driver2 Tilt Memory Position 2) Driver tilt memory position 3 Min.: 0
Max.: 65535
28627 to 36864 For Driver Tilt Memory Position 3
Driver Telescopic Memory Position 3 (Driver2 Telescopic Memory Position 2) Driver telescopic memory position 3 Min.: 0
Max.: 65535
28627 to 36864 For Driver Telescopic Memory Position 3
Tilt Motor Machine Lock Memory Data Tilt Motor Machine Lock Memory Data Not Exist or Existed - -
Telescopic Motor Machine Lock Memory Data Telescopic Motor Machine Lock Memory Data Not Exist or Existed - -
Autoaway/Return Operation Setting Autoaway/Return Operation Setting Tilt&Telescopic OFF, Telescopic ON, Tilt ON or Tilt&Telescopic ON Tilt&Telescopic OFF: Tilt and telescopic operations prohibited
Telescopic ON: Only telescopic operations permitted
Tilt ON: Only tilt operations permitted
Tilt&Telescopic ON: Tilt and telescopic operations permitted
-


ACTIVE TEST


HINT:

Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


a.

Turn the power switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the power switch on (IG).


d.

Turn the GTS on.


e.

Enter the following menus: Body Electrical / Tilt & Telescopic / Active Test.


f.

According to the display on the GTS, perform the Active Test.

Body Electrical > Tilt&Telescopic > Active Test
Tester Display Measurement Item Control Range
Tilt Motor Tilt operation UP/DOWN
Telescopic Motor Telescopic operation LONG/SHORT