Home › Steering › STEERING COLUMN › POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM
RM33C0E _55 Steering _065448 STEERING COLUMN _0331813 POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM C

STEERING COLUMN  POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM  B26031C  Tilt and Telescopic Manual Switch Circuit Circuit Voltage Out of Range  


DESCRIPTION

Different voltage values are sent to the multiplex tilt and telescopic ECU by operating the tilt and telescopic switch. The multiplex tilt and telescopic ECU then judges which motor and in which direction that motor should operate based on the voltage value.

DTC No. Detection Item DTC Detection Condition Trouble Area
B26031C Tilt and Telescopic Manual Switch Circuit Circuit Voltage Out of Range When operating the tilt and telescopic switch, an abnormal voltage value is sent to the multiplex tilt and telescopic ECU.
·

Tilt and telescopic switch

·

Harness or connector

·

Multiplex tilt and telescopic ECU



WIRING DIAGRAM

C240527E64
4.917,3.875 7.073,4.188 2.156,0.313 10 false Multiplex Tilt and Telescopic ECU 1.458,3.75 3.583,3.906 2.125,0.156 10 false Tilt and Telescopic Switch 3.75,2.646 4.115,2.802 0.365,0.156 10 false MSW 3.906,1 4.125,1.156 0.219,0.156 10 false VC 5.125,2.75 5.49,2.906 0.365,0.156 10 false MSW 5.135,1.094 5.354,1.25 0.219,0.156 10 false VC 0.708,1.979 1.333,2.448 0.625,0.469 10 false Tilt Down 1.573,1.896 2.25,2.458 0.677,0.563 10 false Telescopic Contract 2.448,1.979 2.979,2.281 0.531,0.302 10 false Tilt Up 3.333,1.885 4.031,2.469 0.698,0.583 10 false Telescopic Extend 4.927,1 5.104,1.167 0.177,0.167 10 false 5 4.865,2.646 5.104,2.813 0.24,0.167 10 false 18 4.917,3.688 5.292,3.885 0.375,0.198 10 false K72 1.458,3.563 1.781,3.76 0.323,0.198 10 false K44 4.177,2.646 4.354,2.813 0.177,0.167 10 false 3 4.177,1 4.354,1.167 0.177,0.167 10 false 1

PROCEDURE

1.READ VALUE USING GTS (TILT MANUAL SWITCH UP/DOWN, TELESCOPIC MANUAL SWITCH SHORT/LONG)
a.

Turn the power switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the power switch on (IG).


d.

Turn the GTS on.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Tilt&Telescopic > Data List
Tester Display
Tilt Manual Switch Up
Tilt Manual Switch Down
Telescopic Manual Switch Short
Telescopic Manual Switch Long
50003 406 18,19,20,21
Body Electrical > Tilt&Telescopic > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Tilt Manual Switch Up Input state of tilt up switch OFF or ON - -
Tilt Manual Switch Down Input state of tilt down switch OFF or ON - -
Telescopic Manual Switch Short Input state of telescopic contract switch OFF or ON - -
Telescopic Manual Switch Long Input state of telescopic extend switch OFF or ON - -
OK:

The value of each Data List item changes in accordance with the operation of the switch.



Result:
Proceed to
OK
NG



OK

2.CONFIRM DTC

NG

3.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - TILT AND TELESCOPIC SWITCH)
2.CONFIRM DTC
a.

Clear the DTCs.

Body Electrical > Tilt&Telescopic > Clear DTCs
50002 406

b.

Check for DTCs.

Body Electrical > Tilt&Telescopic > Trouble Codes
50001 406

Result:
Result Proceed to
DTCs are output. A
DTCs are not output. B



A

REPLACE MULTIPLEX TILT AND TELESCOPIC ECU

B

3.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - TILT AND TELESCOPIC SWITCH)
a.

Disconnect the K72 multiplex tilt and telescopic ECU connector.


b.

Disconnect the K44 tilt and telescopic switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K72-5 (VC) - K44-1 (VC) Always Below 1 Ω
K72-18 (MSW) - K44-3 (MSW) Always Below 1 Ω
K72-5 (VC) or K44-1 (VC) - Body ground Always 10 kΩ or higher
K72-18 (MSW) or K44-3 (MSW) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK MULTIPLEX TILT AND TELESCOPIC ECU (VC TERMINAL VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK MULTIPLEX TILT AND TELESCOPIC ECU (VC TERMINAL VOLTAGE)
a.
C267905C68
1.521,0.24 1.927,0.49 0.406,0.25 1.167,0.896 1.167,0.667 true 1.167,1.521 1.167,1.146 true 1.594,0.281 1.979,0.49 0.385,0.208 10 false K72 1.073,0.49 1.354,0.656 0.281,0.167 10 false VC 1.01,1.552 1.458,1.771 0.448,0.219 10 false MSW 0.146,0.125 0.458,0.323 0.313,0.198 10 false *a
*a Component with harness connected
(Multiplex Tilt and Telescopic ECU)


Reconnect the K72 multiplex tilt and telescopic ECU connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
K72-5 (VC) - K72-18 (MSW) Power switch on (IG) 4.9 to 5.1 V



Result:
Proceed to
OK
NG



OK

5.CHECK TILT AND TELESCOPIC SWITCH

NG

REPLACE MULTIPLEX TILT AND TELESCOPIC ECU

5.CHECK TILT AND TELESCOPIC SWITCH
a.
C240949C24
1,0.302 1.375,0.552 0.375,0.25 1.479,1.458 1.156,1.844 false 1.938,1.458 2.281,1.854 false 0.125,0.031 0.385,0.188 0.26,0.156 10 false *a 0.938,1.865 1.333,2.052 0.396,0.188 10 false MSW 2.219,1.865 2.615,2.052 0.396,0.188 10 false VC 1.063,0.354 1.458,0.594 0.396,0.24 10 false K44
*a Component without harness connected
(Tilt and Telescopic Switch)


Remove the tilt and telescopic switch.

Click hereSteering>STEERING COLUMN>TILT AND TELESCOPIC MANUAL SWITCH>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K44-1 (VC) - K44-3 (MSW) Tilt up 342 to 378 Ω
Tilt down 1890.5 to 2089.5 Ω
Telescopic contract 750.5 to 829.5 Ω
Telescopic extend 152 to 168 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MULTIPLEX TILT AND TELESCOPIC ECU

NG

REPLACE TILT AND TELESCOPIC SWITCH