The telescopic motor (steering column assembly) is operated by the power source voltage supplied from the multiplex tilt and telescopic ECU and slides the steering column assembly forward and backward. The telescopic position sensor (Hall IC) in the telescopic motor (steering column assembly) detects the sliding position of the steering column assembly in the forward and backward directions and sends a signal to the multiplex tilt and telescopic ECU based on that sliding amount.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B261196 | Telescopic Position Sensor or Telescopic Motor Circuit Component Internal Failure | Telescopic operation stops within the operation range while operating. | ·
TI & TE Fuse ·
Telescopic position sensor (steering column assembly) ·
Telescopic motor (steering column assembly) ·
Harness or connector ·
Multiplex tilt and telescopic ECU |
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
Turn the power switch off.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Check that the steering column contracts and extends.
Enter the following menus: Body Electrical / Tilt & Telescopic / Active Test.
| Tester Display |
|---|
| Telescopic Motor |
| Tester Display | Measurement Item | Control Range |
|---|---|---|
| Telescopic Motor | Telescopic Operation | LONG/SHORT |
The steering column contracts and extends.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the K72 multiplex tilt and telescopic ECU connector.
Disconnect the K92 telescopic motor (steering column assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K72-14 (VCE) - K92-6 (VCE) | Always | Below 1 Ω |
| K72-15 (TES) - K92-7 (TES) | Always | Below 1 Ω |
| K72-17 (E2) - K92-8 (E2) | Always | Below 1 Ω |
| K72-14 (VCE) or K92-6 (VCE) - Body ground | Always | 10 kΩ or higher |
| K72-15 (TES) or K92-7 (TES) - Body ground | Always | 10 kΩ or higher |
| K72-17 (E2) or K92-8 (E2) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Multiplex Tilt and Telescopic ECU) |
Disconnect the K72 multiplex tilt and telescopic ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K72-1 (GND) - Body ground | Always | Below 1 Ω |
| K72-8 (GND2) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the K72 multiplex tilt and telescopic ECU connector.
| *a | Component with harness connected
(Multiplex Tilt and Telescopic ECU) |
Disconnect the K92 telescopic motor (steering column assembly) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K72-14 (VCE) - K72-17 (E2) | Power switch on (IG) | 8 to 14 V |
| K72-15 (TES) - K72-17 (E2) | Power switch on (IG) | 8 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(Telescopic Motor (Steering Column Assembly)) |
Reconnect the K72 multiplex tilt and telescopic ECU connector.
Reconnect the K92 telescopic motor (steering column assembly) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K92-7 (TES) - K92-8 (E2) | Steering column contracting or extending | Pulse generation
High: 8 to 14 V Low: Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the K72 multiplex tilt and telescopic ECU connector.
| *a | Front view of wire harness connector
(to Multiplex Tilt and Telescopic ECU) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K72-2 (+B) - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Multiplex Tilt and Telescopic ECU) |
Disconnect the K72 multiplex tilt and telescopic ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K72-1 (GND) - Body ground | Always | Below 1 Ω |
| K72-8 (GND2) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the K72 multiplex tilt and telescopic ECU connector.
Disconnect the K92 telescopic motor (steering column assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K72-6 (TEM+) - K92-4 (TEM+) | Always | Below 1 Ω |
| K72-19 (TEM-) - K92-1 (TEM-) | Always | Below 1 Ω |
| K72-6 (TEM+) or K92-4 (TEM+) - Body ground | Always | 10 kΩ or higher |
| K72-19 (TEM-) or K92-1 (TEM-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the K92 telescopic motor (steering column assembly) connector.
| *a | Component without harness connected
(Telescopic Motor (Steering Column Assembly)) |
Apply 12 V auxiliary battery voltage to the telescopic motor (steering column assembly) connector. Then check the steering column telescopic operation.
| Measurement Condition | Specified Condition |
|---|---|
·
12 V auxiliary battery positive (+) lead → K92-4 (TEM+) ·
12 V auxiliary battery negative (-) lead → K92-1 (TEM-) |
The steering column contracts. |
·
12 V auxiliary battery positive (+) lead → K92-1 (TEM-) ·
12 V auxiliary battery negative (-) lead → K92-4 (TEM+) |
The steering column extends. |
| Proceed to |
|---|
| OK |
| NG |
OK
NG