Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM33C0E _58 Vehicle Interior _065460 SUPPLEMENTAL RESTRAINT SYSTEMS _0331857 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1612  Front Airbag Sensor Lost Communication (RH)  B1613  Front Airbag Sensor Initialization Error (RH)  


DESCRIPTION

The front airbag sensor RH circuit consists of the airbag sensor assembly and front airbag sensor RH.

The front airbag sensor RH detects impacts to the vehicle and sends signals to the airbag sensor assembly to determine if the airbags and pretensioners should be deployed.

These DTCs are stored when a malfunction is detected in the front airbag sensor RH circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Test Mode / Check Mode
B1612 Front Airbag Sensor Lost Communication (RH)
·

The airbag sensor assembly detects a line short, short to ground or B+, or an open in the front airbag sensor RH circuit.

·

Front airbag sensor RH malfunction

·

Airbag sensor assembly malfunction


·

Instrument panel wire

·

Engine room main wire

·

Front airbag sensor RH

·

Airbag sensor assembly


Comes on Does not apply to test/check mode
B1613 Front Airbag Sensor Initialization Error (RH)
·

The airbag sensor assembly detects a line short, short to ground or B+, or an open in the front airbag sensor RH circuit.

·

Front airbag sensor RH malfunction

·

Airbag sensor assembly malfunction


·

Instrument panel wire

·

Engine room main wire

·

Front airbag sensor RH

·

Airbag sensor assembly


Comes on Does not apply to test/check mode

WIRING DIAGRAM

B473428E07
4.781,2.896 6.854,3.365 2.073,0.469 10 false Airbag Sensor Assembly 4.771,2.729 6.844,3.198 2.073,0.469 10 false K73 4.583,1.021 5.042,1.323 0.458,0.302 10 false 29 4.583,1.698 5.333,2.073 0.75,0.375 10 false 28 4.833,1.021 5.292,1.323 0.458,0.302 10 false +SR 4.844,1.698 5.594,2.073 0.75,0.375 10 false -SR 5.479,1.448 6.156,1.74 0.677,0.292 10 false Interface 1.771,1.448 2.448,1.74 0.677,0.292 10 false Interface 0.76,1.448 1.438,1.74 0.677,0.292 10 false Element 3.75,1.125 4.208,1.427 0.458,0.302 10 false AK6 3.75,1.802 4.208,2.104 0.458,0.302 10 false AK6 3.833,0.938 4.292,1.24 0.458,0.302 10 false 1 3.833,1.615 4.292,1.917 0.458,0.302 10 false 3 3.042,1.021 3.5,1.323 0.458,0.302 10 false 2 3.042,1.708 3.5,2.01 0.458,0.302 10 false 1 2.667,1.021 3.125,1.323 0.458,0.302 10 false +SR 2.708,1.708 3.458,2.083 0.75,0.375 10 false -SR 0.563,2.344 2.635,2.813 2.073,0.469 10 false A42 0.563,2.521 2.635,2.99 2.073,0.469 10 false Front Airbag Sensor RH

CAUTION / NOTICE / HINT

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

1.CHECK CONNECTION OF CONNECTORS
a.

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the airbag sensor assembly and front airbag sensor RH. Also check that the connectors that link the engine room main wire and instrument panel wire are properly connected.

OK:

The connectors are properly connected.



Result:
Proceed to
OK
NG



OK

2.CHECK CONNECTORS

NG

CONNECT CONNECTORS PROPERLY

2.CHECK CONNECTORS
a.

Disconnect the connectors from the airbag sensor assembly and front airbag sensor RH. Also disconnect the connectors that link the engine room main wire and instrument panel wire.


b.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.



Result:
Proceed to
OK
NG



OK

3.CHECK FRONT AIRBAG SENSOR RH CIRCUIT

NG

REPLACE INSTRUMENT PANEL WIRE OR ENGINE ROOM MAIN WIRE

3.CHECK FRONT AIRBAG SENSOR RH CIRCUIT
a.
B473429C01
0.865,0.833 1.219,1.073 0.354,0.24 0.51,3.729 0.865,3.969 0.354,0.24 1.635,1.729 1.635,1.604 false 1.229,1.635 1.594,1.281 false 2.01,1.646 1.688,1.281 false 0.969,4.313 1.26,3.906 false 1.729,4.313 1.427,3.906 false 1.167,2.573 1.167,2.198 1.167,2.198 1,2.198 false 1.792,3.042 1.792,2.708 false 0.292,2.552 0.688,2.969 0.396,0.417 10 false *1 2.729,2.563 3.125,2.865 0.396,0.302 10 false *2 1.563,1.74 1.927,2 0.365,0.26 10 false *5 0.656,0.188 1.021,0.51 0.365,0.323 10 false *a 0.354,3.375 0.74,3.781 0.385,0.406 10 false *b 2.354,2.563 2.75,2.865 0.396,0.302 10 false A 1.979,2.563 2.375,2.865 0.396,0.302 10 false B 1.51,2.563 1.906,2.865 0.396,0.302 10 false C 1.354,2.563 1.75,2.865 0.396,0.302 10 false D 0.896,2.563 1.292,2.865 0.396,0.302 10 false E 0.531,2.563 0.927,2.865 0.396,0.302 10 false F 0.927,0.875 1.292,1.198 0.365,0.323 10 false K73 1.875,1.646 2.333,1.927 0.458,0.281 10 false +SR 1.094,1.646 1.552,1.927 0.458,0.281 10 false -SR 0.573,3.771 0.938,4.094 0.365,0.323 10 false A42 0.833,4.323 1.292,4.604 0.458,0.281 10 false -SR 1.594,4.323 2.052,4.604 0.458,0.281 10 false +SR 0.833,2.125 1.229,2.542 0.396,0.417 10 false *3 1.729,3.063 2.125,3.479 0.396,0.417 10 false *4
*1 Front Airbag Sensor RH
*2 Airbag Sensor Assembly
*3 Engine Room Main Wire
*4 Instrument Panel Wire
*5 Service Wire
*a Front view of wire harness connector
(to Airbag Sensor Assembly)
*b Front view of wire harness connector
(to Front Airbag Sensor RH)


Connect the connectors that link the engine room main wire and instrument panel wire.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Turn the power switch on (IG).


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A42-2 (+SR) - Body ground Power switch on (IG) Below 1 V
A42-1 (-SR) - Body ground Power switch on (IG) Below 1 V



e.

Turn the power switch off.


f.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



g.

Using a service wire, connect terminals 29 (+SR) and 28 (-SR) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A42-2 (+SR) - A42-1 (-SR) Always Below 1 Ω



i.

Disconnect the service wire from connector B.


j.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A42-2 (+SR) - A42-1 (-SR) Always 1 MΩ or higher
A42-2 (+SR) - Body ground Always 1 MΩ or higher
A42-1 (-SR) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK FRONT AIRBAG SENSOR RH

NG

5.CHECK INSTRUMENT PANEL WIRE
4.CHECK FRONT AIRBAG SENSOR RH
a.
C238386C02
2.083,1.01 2.448,1.5 0.365,0.49 10 A 1.927,1.01 2.427,1.479 0.5,0.469 10 B 1.583,1.01 1.969,1.521 0.385,0.51 10 C 1.427,1.01 1.844,1.583 0.417,0.573 10 D 1.083,1.01 1.531,1.667 0.448,0.656 10 E 0.938,1.01 1.521,1.75 0.583,0.74 10 F 0.563,1.021 1.125,1.594 0.563,0.573 10 *1 2.542,1.031 2.885,1.563 0.344,0.531 10 *2
*1 Front Airbag Sensor LH
*2 Airbag Sensor Assembly


Connect the connector to the airbag sensor assembly.


b.

Interchange the front airbag sensor RH with LH and connect the connectors.


c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Turn the power switch on (IG), and wait for at least 60 seconds.


e.

Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs
50002 188

f.

Turn the power switch off.


g.

Turn the power switch on (IG), and wait for at least 60 seconds.


h.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:

Codes other than DTCs B1612, B1613, B1617 and B1618 may be output at this time, but they are not related to this check.



Result:
Result Proceed to
DTCs B1612, B1613, B1617 and B1618 are not output. A
DTC B1617 or B1618 is output. B
DTC B1612 or B1613 is output. C


i.

Turn the power switch off.


j.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



k.

Return the front airbag sensor RH and LH to their original positions and connect the connectors.



A

B

C

5.CHECK INSTRUMENT PANEL WIRE
a.
B473430C01
0.854,0.833 1.208,1.063 0.354,0.229 0.875,3.74 1.24,3.979 0.365,0.24 1.635,1.719 1.635,1.604 false 1.292,1.646 1.604,1.271 false 1.99,1.646 1.688,1.271 false 1.688,2.156 1.854,2.156 1.854,2.156 1.854,2.573 false 1.094,3.042 1.094,2.708 false 2.156,3.51 1.792,3.729 false 2.156,4.135 1.792,3.917 false 0.302,2.563 0.667,2.833 0.365,0.271 10 false *1 2.729,2.563 3.156,2.906 0.427,0.344 10 false *2 1.563,1.729 1.938,1.979 0.375,0.25 10 false *5 1.021,3.052 1.417,3.323 0.396,0.271 10 false *3 1.531,2.083 1.948,2.396 0.417,0.313 10 false *4 0.646,0.177 1.042,0.563 0.396,0.385 10 false *a 0.792,3.417 1.167,3.813 0.375,0.396 10 false *b 2.354,2.563 2.781,2.906 0.427,0.344 10 false A 2.052,2.563 2.479,2.906 0.427,0.344 10 false B 1.583,2.563 2.01,2.906 0.427,0.344 10 false C 1.292,2.563 1.719,2.906 0.427,0.344 10 false D 0.823,2.563 1.25,2.906 0.427,0.344 10 false E 0.521,2.563 0.948,2.906 0.427,0.344 10 false F 0.917,0.865 1.313,1.25 0.396,0.385 10 false K73 1.854,1.646 2.25,2.031 0.396,0.385 10 false +SR 1.146,1.646 1.542,2.031 0.396,0.385 10 false -SR 2.198,3.427 2.583,3.708 0.385,0.281 10 false +SR 2.198,4.073 2.594,4.458 0.396,0.385 10 false -SR 0.927,3.781 1.323,4.167 0.396,0.385 10 false AK6
*1 Front Airbag Sensor RH
*2 Airbag Sensor Assembly
*3 Engine Room Main Wire
*4 Instrument Panel Wire
*5 Service Wire
*a Front view of wire harness connector
(to Airbag Sensor Assembly)
*b Front view of wire harness connector
(to Engine Room Main Wire)


Disconnect the instrument panel wire connector from the engine room main wire.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Turn the power switch on (IG).


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
AK6-1 (+SR) - Body ground Power switch on (IG) Below 1 V
AK6-3 (-SR) - Body ground Power switch on (IG) Below 1 V



e.

Turn the power switch off.


f.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



g.

Using a service wire, connect terminals 29 (+SR) and 28 (-SR) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
AK6-1 (+SR) - AK6-3 (-SR) Always Below 1 Ω



i.

Disconnect the service wire from connector B.


j.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
AK6-1 (+SR) - AK6-3 (-SR) Always 1 MΩ or higher
AK6-1 (+SR) - Body ground Always 1 MΩ or higher
AK6-3 (-SR) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE ENGINE ROOM MAIN WIRE

NG

REPLACE INSTRUMENT PANEL WIRE