The front airbag sensor LH circuit consists of the airbag sensor assembly and front airbag sensor LH.
The front airbag sensor LH detects impacts to the vehicle and sends signals to the airbag sensor assembly to determine if the airbags and pretensioners should be deployed.
These DTCs are stored when a malfunction is detected in the front airbag sensor LH circuit.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Warning Indicate | Test Mode / Check Mode |
|---|---|---|---|---|---|
| B1617 | Front Airbag Sensor Lost Communication (LH) | ·
The airbag sensor assembly detects a line short, short to ground or B+, or an open in the front airbag sensor LH circuit. ·
Front airbag sensor LH malfunction ·
Airbag sensor assembly malfunction |
·
Instrument panel wire ·
Engine room main wire ·
Front airbag sensor LH ·
Airbag sensor assembly |
Comes on | Does not apply to test/check mode |
| B1618 | Front Airbag Sensor Initialization Error (LH) | ·
The airbag sensor assembly detects a line short, short to ground or B+, or an open in the front airbag sensor LH circuit. ·
Front airbag sensor LH malfunction ·
Airbag sensor assembly malfunction |
·
Instrument panel wire ·
Engine room main wire ·
Front airbag sensor LH ·
Airbag sensor assembly |
Comes on | Does not apply to test/check mode |
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
Check that the connectors are properly connected to the airbag sensor assembly and front airbag sensor LH. Also check that the connectors that link the engine room main wire and instrument panel wire are properly connected.
The connectors are properly connected.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the connectors from the airbag sensor assembly and front airbag sensor LH. Also disconnect the connectors that link the engine room main wire and instrument panel wire.
Check that the terminals of the connectors are not deformed or damaged.
The terminals are not deformed or damaged.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Front Airbag Sensor LH |
| *2 | Airbag Sensor Assembly |
| *3 | Engine Room Main Wire |
| *4 | Instrument Panel Wire |
| *5 | Service Wire |
| *a | Front view of wire harness connector
(to Airbag Sensor Assembly) |
| *b | Front view of wire harness connector
(to Front Airbag Sensor LH) |
Connect the connectors that link the engine room main wire and instrument panel wire.
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the power switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A43-2 (+SL) - Body ground | Power switch on (IG) | Below 1 V |
| A43-1 (-SL) - Body ground | Power switch on (IG) | Below 1 V |
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
Using a service wire, connect terminals 30 (+SL) and 31 (-SL) of connector B.
Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A43-2 (+SL) - A43-1 (-SL) | Always | Below 1 Ω |
Disconnect the service wire from connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A43-2 (+SL) - A43-1 (-SL) | Always | 1 MΩ or higher |
| A43-2 (+SL) - Body ground | Always | 1 MΩ or higher |
| A43-1 (-SL) - Body ground | Always | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Front Airbag Sensor RH |
| *2 | Airbag Sensor Assembly |
Connect the connector to the airbag sensor assembly.
Interchange the front airbag sensor LH with RH and connect the connectors.
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the power switch on (IG), and wait for at least 60 seconds.
Clear the DTCs stored in memory.
Turn the power switch off.
Turn the power switch on (IG), and wait for at least 60 seconds.
Check for DTCs.
Codes other than DTCs B1612, B1613, B1617 and B1618 may be output at this time, but they are not related to this check.
| Result | Proceed to |
|---|---|
| DTCs B1612, B1613, B1617 and B1618 are not output. | A |
| DTC B1617 or B1618 is output. | B |
| DTC B1612 or B1613 is output. | C |
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
Return the front airbag sensor LH and RH to their original positions and connect the connectors.
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
C
| *1 | Front Airbag Sensor LH |
| *2 | Airbag Sensor Assembly |
| *3 | Engine Room Main Wire |
| *4 | Instrument Panel Wire |
| *5 | Service Wire |
| *a | Front view of wire harness connector
(to Airbag Sensor Assembly) |
| *b | Front view of wire harness connector
(to Engine Room Main Wire) |
Disconnect the instrument panel wire connector from the engine room main wire.
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the power switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| AK6-2 (+SL) - Body ground | Power switch on (IG) | Below 1 V |
| AK6-4 (-SL) - Body ground | Power switch on (IG) | Below 1 V |
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
Using a service wire, connect terminals 30 (+SL) and 31 (-SL) of connector B.
Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| AK6-2 (+SL) - AK6-4 (-SL) | Always | Below 1 Ω |
Disconnect the service wire from connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| AK6-2 (+SL) - AK6-4 (-SL) | Always | 1 MΩ or higher |
| AK6-2 (+SL) - Body ground | Always | 1 MΩ or higher |
| AK6-4 (-SL) - Body ground | Always | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG