Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM33C0E _58 Vehicle Interior _065460 SUPPLEMENTAL RESTRAINT SYSTEMS _0331857 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1865  Short in Knee Airbag (P Side) Squib Circuit  B1866  Open in Knee Airbag (P Side) Squib Circuit  B1867  Short in Knee Airbag (P Side) Squib Circuit (to Ground)  B1868  Short in Knee Airbag (P Side) Squib Circuit (to +B)  


DESCRIPTION

The front passenger side knee airbag squib circuit consists of the airbag sensor assembly and lower No. 2 instrument panel airbag assembly.

The airbag sensor assembly uses this circuit to deploy the airbag when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the front passenger side knee airbag squib circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Test Mode / Check Mode
B1865 Short in Knee Airbag (P Side) Squib Circuit
·

The airbag sensor assembly detects a line short in the front passenger side knee airbag squib during the primary check.

·

Front passenger side knee airbag squib malfunction

·

Airbag sensor assembly malfunction


·

Instrument panel wire

·

Front passenger side knee airbag squib (Lower No. 2 instrument panel airbag assembly)

·

Airbag sensor assembly


Comes on Applies to check mode
B1866 Open in Knee Airbag (P Side) Squib Circuit
·

The airbag sensor assembly detects an open in the front passenger side knee airbag squib.

·

Front passenger side knee airbag squib malfunction

·

Airbag sensor assembly malfunction


·

Instrument panel wire

·

Front passenger side knee airbag squib (Lower No. 2 instrument panel airbag assembly)

·

Airbag sensor assembly


Comes on Applies to check mode
B1867 Short in Knee Airbag (P Side) Squib Circuit (to Ground)
·

The airbag sensor assembly detects a short to ground in the front passenger side knee airbag squib.

·

Front passenger side knee airbag squib malfunction

·

Airbag sensor assembly malfunction


·

Instrument panel wire

·

Front passenger side knee airbag squib (Lower No. 2 instrument panel airbag assembly)

·

Airbag sensor assembly


Comes on Applies to check mode
B1868 Short in Knee Airbag (P Side) Squib Circuit (to +B)
·

The airbag sensor assembly detects a short to B+ in the front passenger side knee airbag squib.

·

Front passenger side knee airbag squib malfunction

·

Airbag sensor assembly malfunction


·

Instrument panel wire

·

Front passenger side knee airbag squib (Lower No. 2 instrument panel airbag assembly)

·

Airbag sensor assembly


Comes on Applies to check mode

WIRING DIAGRAM

B475055E43
4.896,3.083 7.146,3.49 2.25,0.406 10 false Airbag Sensor Assembly 4.885,2.917 6.552,3.438 1.667,0.521 10 false K73 4.708,1.333 5.51,1.979 0.802,0.646 10 false 10 4.719,1.896 5.521,2.542 0.802,0.646 10 false 11 4.958,1.333 5.76,1.979 0.802,0.646 10 false PK+ 4.958,1.896 5.76,2.542 0.802,0.646 10 false PK- 0.875,2.406 2.542,2.927 1.667,0.521 10 false K82 0.875,2.573 3.469,3.208 2.594,0.635 10 false Front Passenger Side Knee Airbag Squib (Lower No. 2 Instrument Panel Airbag Assembly) 2.083,1.333 2.885,1.979 0.802,0.646 10 false 1 2.083,1.885 2.885,2.531 0.802,0.646 10 false 2 1.719,1.333 2.521,1.979 0.802,0.646 10 false PK+ 1.729,1.885 2.531,2.531 0.802,0.646 10 false PK-

CAUTION / NOTICE / HINT

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


HINT:
·

Perform the simulation method by selecting check mode (Signal Check) using the GTS.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE

·

After selecting check mode (Signal Check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city road or rough road.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING



PROCEDURE

1.CHECK CONNECTORS
a.
C239229C01
0.552,1.115 0.552,1.542 false 1.313,0.979 1.313,0.604 1.313,0.604 1.146,0.604 false 0.469,1.573 0.958,1.958 0.49,0.385 10 *1 0.979,0.531 1.313,0.854 0.333,0.323 10 *3 2.313,0.969 2.625,1.344 0.313,0.375 10 *2 1.865,0.969 2.188,1.427 0.323,0.458 10 A 1.5,0.969 1.802,1.406 0.302,0.438 10 B 1.021,0.969 1.396,1.417 0.375,0.448 10 C 0.656,0.969 1.146,1.531 0.49,0.563 10 D
*1 Lower No. 2 Instrument Panel Airbag Assembly
*2 Airbag Sensor Assembly
*3 Instrument Panel Wire


Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the lower No. 2 instrument panel airbag assembly and airbag sensor assembly.

OK:

The connectors are properly connected.


HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the lower No. 2 instrument panel airbag assembly and airbag sensor assembly.


e.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.



f.

Check that the instrument panel wire connector (on the lower No. 2 instrument panel airbag assembly side) is not loose, deformed or damaged.

OK:

The airbag connector locking button is not disengaged, and the claw of the lock is not deformed or damaged.



g.

Check that the short springs of the activation prevention mechanism of the instrument panel wire connector are not deformed or damaged.

OK:

The short springs are not deformed or damaged.



Result:
Proceed to
OK
NG



OK

2.CHECK LOWER NO. 2 INSTRUMENT PANEL AIRBAG ASSEMBLY

NG

REPLACE INSTRUMENT PANEL WIRE

2.CHECK LOWER NO. 2 INSTRUMENT PANEL AIRBAG ASSEMBLY
a.
C247056C07
0.448,2.24 0.833,2.479 0.385,0.24 0.667,0.906 0.667,1.302 false 1.844,2.26 2.021,2.26 false 0.594,1.313 0.938,1.656 0.344,0.344 10 false *1 2.25,0.75 2.573,1.115 0.323,0.365 10 false *2 1.813,0.76 2.083,1.094 0.271,0.333 10 false A 1.656,0.76 1.979,1.198 0.323,0.438 10 false B 1.146,0.76 1.385,1.156 0.24,0.396 10 false C 0.781,0.76 1.063,1.188 0.281,0.427 10 false D 0.521,2.281 0.885,2.583 0.365,0.302 10 false K82 2.063,2.177 2.542,2.552 0.479,0.375 10 false SST 0.313,1.698 0.625,2.146 0.313,0.448 10 false *a
*1 Lower No. 2 Instrument Panel Airbag Assembly
*2 Airbag Sensor Assembly
*a Front view of wire harness connector
(to Lower No. 2 Instrument Panel Airbag Assembly)


Connect the connector to the airbag sensor assembly.


b.

Connect SST (resistance 2.1 Ω) to connector C.

CAUTION:

Never connect a tester to the lower No. 2 instrument panel airbag assembly for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting it.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Turn the power switch on (IG), and wait for at least 60 seconds.


e.

Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs
50002 188

f.

Turn the power switch off.


g.

Turn the power switch on (IG), and wait for at least 60 seconds.


h.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 188
OK:

DTC B1865, B1866, B1867 or B1868 is not output.


HINT:

Codes other than DTCs B1865, B1866, B1867 and B1868 may be output at this time, but they are not related to this check.



i.

Turn the power switch off.


j.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



k.

Disconnect SST from connector C.


Result:
Proceed to
OK
NG



OK

NG

3.CHECK INSTRUMENT PANEL WIRE
3.CHECK INSTRUMENT PANEL WIRE
a.
C245639C12
0.51,2.219 0.875,2.458 0.365,0.24 1.469,2.323 1.073,2.563 false 1.698,2.323 2.042,2.563 false 0.51,0.875 0.51,0.458 0.51,0.458 0.375,0.458 false 1.354,0.875 1.354,0.458 1.354,0.458 1.219,0.458 false 0.635,0.865 1.135,1.208 0.5,0.344 10 false D 1.031,0.865 1.354,1.177 0.323,0.313 10 false C 1.594,0.875 1.927,1.167 0.333,0.292 10 false B 1.99,0.875 2.563,1.271 0.573,0.396 10 false A 2.406,0.875 2.74,1.135 0.333,0.26 10 false *2 0.938,2.573 1.396,2.875 0.458,0.302 10 false PK+ 0.583,2.26 0.99,2.573 0.406,0.313 10 false K82 2,2.573 2.635,2.885 0.635,0.313 10 false PK- 0.302,1.875 0.604,2.177 0.302,0.302 10 false *a 0.219,0.385 0.688,0.698 0.469,0.313 10 false *1 1.073,0.385 1.552,0.708 0.479,0.323 10 false *3
*1 Lower No. 2 Instrument Panel Airbag Assembly
*2 Airbag Sensor Assembly
*3 Instrument Panel Wire
*a Front view of wire harness connector
(to Lower No. 2 Instrument Panel Airbag Assembly)


Disconnect the instrument panel wire from the airbag sensor assembly.


b.

Check for a short to B+ in the circuit.

i.

Connect the cable to the negative (-) auxiliary battery terminal.


ii.

Turn the power switch on (IG).


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
K82-1 (PK+) - Body ground Power switch on (IG) Below 1 V
K82-2 (PK-) - Body ground Power switch on (IG) Below 1 V



iv.

Turn the power switch off.


v.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.




c.

Check for an open in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K82-1 (PK+) - K82-2 (PK-) Always Below 1 Ω




d.

Check for a short to ground in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K82-1 (PK+) - Body ground Always 1 MΩ or higher
K82-2 (PK-) - Body ground Always 1 MΩ or higher




e.

Check for a short in the circuit.

i.

Release the activation prevention mechanism built into connector B.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>SYSTEM DESCRIPTION


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K82-1 (PK+) - K82-2 (PK-) Always 1 MΩ or higher



iii.

Restore the released activation prevention mechanism of connector B to the original condition.



Result:
Proceed to
OK
NG



OK

4.CHECK DTC

NG

REPLACE INSTRUMENT PANEL WIRE

4.CHECK DTC
a.
C238245C01
0.844,1.146 0.844,1.458 false 0.969,1 1.219,1.385 0.25,0.385 10 false D 1.125,1 1.333,1.417 0.208,0.417 10 false C 1.583,1 1.823,1.354 0.24,0.354 10 false B 1.74,1 2,1.323 0.26,0.323 10 false A 2.167,0.99 2.458,1.313 0.292,0.323 10 false *2 0.76,1.479 1.083,1.781 0.323,0.302 10 false *1
*1 Lower No. 2 Instrument Panel Airbag Assembly
*2 Airbag Sensor Assembly


Connect the connectors to the lower No. 2 instrument panel airbag assembly and airbag sensor assembly.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Turn the power switch on (IG), and wait for at least 60 seconds.


d.

Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs
50002 188

e.

Turn the power switch off.


f.

Turn the power switch on (IG), and wait for at least 60 seconds.


g.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 188
OK:

DTC B1865, B1866, B1867 or B1868 is not output.


HINT:

Codes other than DTCs B1865, B1866, B1867 and B1868 may be output at this time, but they are not related to this check.



Result:
Proceed to
OK
NG



OK

NG