The side collision sensor RH circuit (bus 2) consists of the airbag sensor assembly and side No. 1 airbag sensor RH.
The side No. 1 airbag sensor RH detects impacts to the vehicle and sends signals to the airbag sensor assembly to determine if the airbags and pretensioners should be deployed.
These DTCs are stored when a malfunction is detected in the side collision sensor RH circuit (bus 2).
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Warning Indicate | Test Mode / Check Mode |
|---|---|---|---|---|---|
| B162B | Side Airbag Sensor Assembly No.2 Lost Communication (RH) | ·
The airbag sensor assembly detects a line short, short to ground or B+, or an open in the side collision sensor RH circuit (bus 2). ·
Side No. 1 airbag sensor RH malfunction ·
Airbag sensor assembly malfunction |
·
Floor wire ·
Side No. 1 airbag sensor RH ·
Airbag sensor assembly |
Comes on | Does not apply to test/check mode |
| B162C | Side Airbag Sensor Assembly No.2 Initialization Error (RH) | ·
The airbag sensor assembly detects a line short, short to ground or B+, or an open in the side collision sensor RH circuit (bus 2). ·
Side No. 1 airbag sensor RH malfunction ·
Airbag sensor assembly malfunction |
·
Floor wire ·
Side No. 1 airbag sensor RH ·
Airbag sensor assembly |
Comes on | Does not apply to test/check mode |
| B1694 | No.2 Side Satellite Sensor Bus RH Initialization Incomplete | ·
The airbag sensor assembly detects a line short, short to ground or B+, or an open in the side collision sensor RH circuit (bus 2). ·
Side No. 1 airbag sensor RH malfunction ·
Airbag sensor assembly malfunction |
·
Floor wire ·
Side No. 1 airbag sensor RH ·
Airbag sensor assembly |
Comes on | Does not apply to test/check mode |
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
Check that the connectors are properly connected to the airbag sensor assembly and side No. 1 airbag sensor RH.
The connectors are properly connected.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the connectors from the airbag sensor assembly and side No. 1 airbag sensor RH.
Check that the terminals of the connectors are not deformed or damaged.
The terminals are not deformed or damaged.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Side No. 1 Airbag Sensor RH |
| *2 | Airbag Sensor Assembly |
| *3 | Floor Wire |
| *4 | Service Wire |
| *a | Front view of wire harness connector
(to Airbag Sensor Assembly) |
| *b | Front view of wire harness connector
(to Side No. 1 Airbag Sensor RH) |
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the power switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| R35-2 (BFR+) - Body ground | Power switch on (IG) | Below 1 V |
| R35-1 (BFR-) - Body ground | Power switch on (IG) | Below 1 V |
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
Using a service wire, connect terminals 28 (BCR+) and 27 (BCR-) of connector B.
Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| R35-2 (BFR+) - R35-1 (BFR-) | Always | Below 1 Ω |
Disconnect the service wire from connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| R35-2 (BFR+) - R35-1 (BFR-) | Always | 1 MΩ or higher |
| R35-2 (BFR+) - Body ground | Always | 1 MΩ or higher |
| R35-1 (BFR-) - Body ground | Always | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Side No. 1 Airbag Sensor LH |
| *2 | Airbag Sensor Assembly |
Connect the connector to the airbag sensor assembly.
Interchange the side No. 1 airbag sensor RH with LH and connect the connectors.
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the power switch on (IG), and wait for at least 60 seconds.
Clear the DTCs stored in memory.
Turn the power switch off.
Turn the power switch on (IG), and wait for at least 60 seconds.
Check for DTCs.
Codes other than DTCs B162B, B162C, B163B, B163C, B1694 and B1699 may be output at this time, but they are not related to this check.
| Result | Proceed to |
|---|---|
| DTC B162B, B162C or B1694 is output. | A |
| DTC B163B, B163C or B1699 is output. | B |
| DTCs B162B, B162C, B163B, B163C, B1694 and B1699 are not output. | C |
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
Return the side No. 1 airbag sensor RH and LH to their original positions and connect the connectors.
A
B
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SIDE AIRBAG SENSOR (for Center Pillar)>REMOVAL
C
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING