Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM33C0E _58 Vehicle Interior _065460 SUPPLEMENTAL RESTRAINT SYSTEMS _0331857 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B163A  Side Airbag Sensor Assembly No.2 (LH)  


DESCRIPTION

The side collision sensor LH circuit (bus 2) consists of the airbag sensor assembly and side No. 1 airbag sensor LH.

The side No. 1 airbag sensor LH detects impacts to the vehicle and sends signals to the airbag sensor assembly to determine if the airbags and pretensioners should be deployed.

DTC B163A is stored when a malfunction is detected in the side No. 1 airbag sensor LH.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Test Mode / Check Mode
B163A Side Airbag Sensor Assembly No.2 (LH)
·

Side No. 1 airbag sensor LH malfunction

·

Airbag sensor assembly malfunction


·

Side No. 1 airbag sensor LH

·

Airbag sensor assembly


Comes on Does not apply to test/check mode

CAUTION / NOTICE / HINT

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

1.CHECK SIDE NO. 1 AIRBAG SENSOR LH
a.
C238328C01
0.719,0.813 1.073,1.24 0.354,0.427 10 false *1 1.104,0.813 1.354,1.25 0.25,0.438 10 false D 1.26,0.813 1.573,1.167 0.313,0.354 10 false C 1.729,0.813 2.031,1.073 0.302,0.26 10 false B 1.885,0.813 2.135,1.073 0.25,0.26 10 false A 2.323,1.135 2.646,1.385 0.323,0.25 10 false *2
*1 Side No. 1 Airbag Sensor RH
*2 Airbag Sensor Assembly


Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Interchange the side No. 1 airbag sensor LH with RH and connect the connectors.


d.

Connect the cable to the negative (-) auxiliary battery terminal.


e.

Turn the power switch on (IG), and wait for at least 60 seconds.


f.

Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs
50002 188

g.

Turn the power switch off.


h.

Turn the power switch on (IG), and wait for at least 60 seconds.


i.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:

Codes other than DTCs B162A and B163A may be output at this time, but they are not related to this check.



Result:
Result Proceed to
DTC B163A is output. A
DTC B162A is output. B
DTCs B162A and B163A are not output. C


j.

Turn the power switch off.


k.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



l.

Return the side No. 1 airbag sensor LH and RH to their original positions and connect the connectors.



A

B

C