Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM33C0E _58 Vehicle Interior _065460 SUPPLEMENTAL RESTRAINT SYSTEMS _0331857 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1642  Side Satellite Sensor Bus Lost Communication (RH)  B1643  Side Satellite Sensor Bus Initialization Error (RH)  


DESCRIPTION

The side collision sensor RH circuit (bus 1) consists of the airbag sensor assembly, door side airbag sensor RH and side No. 2 airbag sensor RH.

The door side airbag sensor RH and side No. 2 airbag sensor RH detect impacts to the vehicle and send signals to the airbag sensor assembly to determine if the airbags and pretensioners should be deployed.

These DTCs are stored when a malfunction is detected in the side collision sensor RH circuit (bus 1).

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Test Mode / Check Mode
B1642 Side Satellite Sensor Bus Lost Communication (RH)
·

The airbag sensor assembly detects a line short, short to ground or B+, or an open in the side collision sensor RH circuit (bus 1).

·

Side No. 2 airbag sensor RH malfunction

·

Door side airbag sensor RH malfunction

·

Airbag sensor assembly malfunction


·

Floor wire

·

Front door wire RH

·

Side No. 2 airbag sensor RH

·

Door side airbag sensor RH

·

Airbag sensor assembly


Comes on Does not apply to test/check mode
B1643 Side Satellite Sensor Bus Initialization Error (RH)
·

The airbag sensor assembly detects a line short, short to ground or B+, or an open in the side collision sensor RH circuit (bus 1).

·

Side No. 2 airbag sensor RH malfunction

·

Door side airbag sensor RH malfunction

·

Airbag sensor assembly malfunction


·

Floor wire

·

Front door wire RH

·

Side No. 2 airbag sensor RH

·

Door side airbag sensor RH

·

Airbag sensor assembly


Comes on Does not apply to test/check mode

WIRING DIAGRAM

B473433E13
4.594,1.99 6.26,2.354 1.667,0.365 10 false Airbag Sensor Assembly 4.594,1.823 6.26,2.188 1.667,0.365 10 false R31 5.219,0.948 5.844,1.271 0.625,0.323 10 false Interface 1.656,2.531 2.281,2.854 0.625,0.323 10 false Interface 4.927,3.229 6.51,3.573 1.583,0.344 10 false Interface 0.771,2.542 1.406,2.833 0.635,0.292 10 false Element 5.865,3.229 6.5,3.521 0.635,0.292 10 false Element 4.646,0.51 6.313,0.875 1.667,0.365 10 false BBR+ 4.646,1.177 6.313,1.542 1.667,0.365 10 false BBR- 4.396,0.51 4.979,0.875 0.583,0.365 10 false 25 4.396,1.177 6.063,1.542 1.667,0.365 10 false 26 2.396,1.427 4.063,1.792 1.667,0.365 10 false BCR+ 2.854,1.427 4.521,1.792 1.667,0.365 10 false 4 2.417,2.094 4.083,2.458 1.667,0.365 10 false BCR- 2.854,2.094 4.521,2.458 1.667,0.365 10 false 3 2.406,2.781 4.073,3.146 1.667,0.365 10 false BDR+ 2.844,2.781 4.51,3.146 1.667,0.365 10 false 1 2.417,3.458 4.083,3.823 1.667,0.365 10 false BDR- 2.844,3.469 4.51,3.833 1.667,0.365 10 false 2 3.438,2.885 5.104,3.25 1.667,0.365 10 false NR1 3.438,3.573 5.104,3.938 1.667,0.365 10 false NR1 3.49,2.688 5.156,3.052 1.667,0.365 10 false 23 3.49,3.375 5.156,3.74 1.667,0.365 10 false 41 4.208,2.781 5.875,3.146 1.667,0.365 10 false 2 4.208,3.458 5.875,3.823 1.667,0.365 10 false 1 4.375,2.781 6.042,3.146 1.667,0.365 10 false BDR+ 4.375,3.458 6.042,3.823 1.667,0.365 10 false BDR- 0.563,4.125 2.229,4.49 1.667,0.365 10 false R33 0.563,4.302 2.885,4.667 2.323,0.365 10 false Side No. 2 Airbag Sensor RH 4.333,4.125 6,4.49 1.667,0.365 10 false N12 4.333,4.302 6.448,4.563 2.115,0.26 10 false Door Side Airbag Sensor RH

CAUTION / NOTICE / HINT

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

1.CHECK CONNECTION OF CONNECTORS
a.

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the airbag sensor assembly, door side airbag sensor RH and side No. 2 airbag sensor RH. Also check that the connectors that link the floor wire and front door wire RH are properly connected.

OK:

The connectors are properly connected.



Result:
Proceed to
OK
NG



OK

2.CHECK CONNECTORS

NG

CONNECT CONNECTORS PROPERLY

2.CHECK CONNECTORS
a.

Disconnect the connectors from the airbag sensor assembly, door side airbag sensor RH and side No. 2 airbag sensor RH. Also disconnect the connectors that link the floor wire and front door wire RH.


b.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.



Result:
Proceed to
OK
NG



OK

3.CHECK FLOOR WIRE

NG

REPLACE FLOOR WIRE OR FRONT DOOR WIRE RH

3.CHECK FLOOR WIRE
a.
B474702C01
0.823,0.844 1.188,1.063 0.365,0.219 0.885,3.74 1.25,3.958 0.365,0.219 1.271,1.719 1.635,1.292 false 2.094,1.719 1.74,1.292 false 1.698,1.823 1.698,1.677 false 1.625,2.854 1.625,2.375 1.625,2.375 1.458,2.375 false 1.729,4.26 1.948,3.865 false 2.302,4.26 2.063,3.865 false 0.76,2.844 1.219,3.344 0.458,0.5 10 false *1 2.521,2.573 3.031,2.948 0.51,0.375 10 false *2 1.313,2.292 1.844,2.833 0.531,0.542 10 false *3 1.635,1.823 2.115,2.24 0.479,0.417 10 false *4 0.656,0.177 1.156,0.677 0.5,0.5 10 false *a 0.698,3.417 1.156,3.792 0.458,0.375 10 false *b 2.188,2.844 2.698,3.219 0.51,0.375 10 false A 1.885,2.844 2.396,3.219 0.51,0.375 10 false B 1.292,2.844 1.802,3.219 0.51,0.375 10 false C 0.979,2.844 1.49,3.219 0.51,0.375 10 false D 1.115,1.729 1.573,2.229 0.458,0.5 10 false BBR+ 0.948,3.771 1.406,4.271 0.458,0.5 10 false R33 1.969,1.729 2.427,2.229 0.458,0.5 10 false BBR- 0.896,0.875 1.354,1.375 0.458,0.5 10 false R31 2.167,4.271 2.677,4.521 0.51,0.25 10 false BCR+ 1.573,4.271 2.083,4.521 0.51,0.25 10 false BCR-
*1 Side No. 2 Airbag Sensor RH
*2 Airbag Sensor Assembly
*3 Floor Wire
*4 Service Wire
*a Front view of wire harness connector
(to Airbag Sensor Assembly)
*b Front view of wire harness connector
(to Side No. 2 Airbag Sensor RH)


Connect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
R33-4 (BCR+) - Body ground Power switch on (IG) Below 1 V
R33-3 (BCR-) - Body ground Power switch on (IG) Below 1 V



d.

Turn the power switch off.


e.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



f.

Using a service wire, connect terminals 25 (BBR+) and 26 (BBR-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R33-4 (BCR+) - R33-3 (BCR-) Always Below 1 Ω



h.

Disconnect the service wire from connector B.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R33-4 (BCR+) - R33-3 (BCR-) Always 1 MΩ or higher
R33-4 (BCR+) - Body ground Always 1 MΩ or higher
R33-3 (BCR-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK WIRE HARNESS

NG

REPLACE FLOOR WIRE

4.CHECK WIRE HARNESS
a.
C295812C06
0.833,0.625 1.25,0.875 0.417,0.25 0.5,3.615 0.917,3.865 0.417,0.25 0.948,4.146 1.375,3.771 false 2.052,4.167 1.656,3.76 false 1.531,4.385 1.531,4.219 false 1.448,1.24 1.76,0.781 false 2.219,1.24 1.938,0.781 false 1.448,2.344 1.448,1.906 1.448,1.906 1.24,1.906 false 1.958,2.771 1.958,2.469 false 0.552,2.333 1.042,2.781 0.49,0.448 10 false *1 2.719,2.333 3.208,2.802 0.49,0.469 10 false *2 1.469,4.385 1.854,4.667 0.385,0.281 10 false *5 0.635,0.177 1.073,0.656 0.438,0.479 10 false *a 0.354,3.167 0.792,3.813 0.438,0.646 10 false *b 2.385,2.333 2.875,2.802 0.49,0.469 10 false A 2.083,2.333 2.573,2.802 0.49,0.469 10 false B 1.74,2.333 2.229,2.802 0.49,0.469 10 false C 1.583,2.333 2.073,2.802 0.49,0.469 10 false D 1.229,2.333 1.719,2.802 0.49,0.469 10 false E 0.927,2.333 1.417,2.802 0.49,0.469 10 false F 1.302,1.25 1.844,1.521 0.542,0.271 10 false BDR+ 2.083,1.25 2.75,1.667 0.667,0.417 10 false BDR- 1.906,4.167 2.406,4.635 0.5,0.469 10 false BDR+ 0.792,4.167 1.292,4.5 0.5,0.333 10 false BDR- 0.917,0.667 1.458,0.938 0.542,0.271 10 false R33 0.594,3.656 1.135,3.927 0.542,0.271 10 false N12 1.083,1.833 1.469,2.115 0.385,0.281 10 false *3 1.896,2.792 2.281,3.073 0.385,0.281 10 false *4
*1 Door Side Airbag Sensor RH
*2 Side No. 2 Airbag Sensor RH
*3 Front Door Wire RH
*4 Floor Wire
*5 Service Wire
*a Front view of wire harness connector
(to Side No. 2 Airbag Sensor RH)
*b Front view of wire harness connector
(to Door Side Airbag Sensor RH)


Connect the connectors that link the floor wire and front door wire RH.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Turn the power switch on (IG).


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
R33-1 (BDR+) - Body ground Power switch on (IG) Below 1 V
R33-2 (BDR-) - Body ground Power switch on (IG) Below 1 V



e.

Turn the power switch off.


f.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



g.

Using a service wire, connect terminals 2 (BDR+) and 1 (BDR-) of connector E.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R33-1 (BDR+) - R33-2 (BDR-) Always Below 1 Ω



i.

Disconnect the service wire from connector E.


j.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R33-1 (BDR+) - R33-2 (BDR-) Always 1 MΩ or higher
R33-1 (BDR+) - Body ground Always 1 MΩ or higher
R33-2 (BDR-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK SIDE NO. 2 AIRBAG SENSOR RH

NG

7.CHECK FLOOR WIRE
5.CHECK SIDE NO. 2 AIRBAG SENSOR RH
a.
C238218C02
0.802,1.156 1.438,1.75 0.635,0.594 10 false *1 2.302,0.885 2.594,1.208 0.292,0.323 10 false *2 1.719,1.167 2.021,1.604 0.302,0.438 10 false B 1.875,1.167 2.271,1.625 0.396,0.458 10 false A 1.271,1.167 1.552,1.583 0.281,0.417 10 false C 1.115,1.167 1.594,1.729 0.479,0.563 10 false D
*1 Side No. 2 Airbag Sensor LH
*2 Airbag Sensor Assembly


Connect the connectors to the door side airbag sensor RH and airbag sensor assembly.


b.

Interchange the side No. 2 airbag sensor RH with LH and connect the connectors.


c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Turn the power switch on (IG), and wait for at least 60 seconds.


e.

Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs
50002 188

f.

Turn the power switch off.


g.

Turn the power switch on (IG), and wait for at least 60 seconds.


h.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:

Codes other than DTCs B1642, B1643, B1647 and B1648 may be output at this time, but they are not related to this check.



Result:
Result Proceed to
DTC B1642 or B1643 is output. A
DTC B1647 or B1648 is output. B
DTCs B1642, B1643, B1647 and B1648 are not output. C


i.

Turn the power switch off.


j.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



k.

Return the side No. 2 airbag sensor RH and LH to their original positions and connect the connectors.



A

6.CHECK DOOR SIDE AIRBAG SENSOR RH

B

C

6.CHECK DOOR SIDE AIRBAG SENSOR RH
a.
C238395C02
0.719,1.021 1.51,1.656 0.792,0.635 10 false *1 2.552,1 2.906,1.406 0.354,0.406 10 false *2 2.26,1.021 2.531,1.51 0.271,0.49 10 false A 2.104,1.021 2.531,1.563 0.427,0.542 10 false B 1.76,1.021 2.24,1.583 0.479,0.563 10 false C 1.604,1.021 2.031,1.615 0.427,0.594 10 false D 1.26,1.021 1.708,1.625 0.448,0.604 10 false E 1.115,1.021 1.792,1.771 0.677,0.75 10 false F
*1 Door Side Airbag Sensor LH
*2 Side No. 2 Airbag Sensor RH


Interchange the door side airbag sensor RH with LH and connect the connectors.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Turn the power switch on (IG), and wait for at least 60 seconds.


d.

Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs
50002 188

e.

Turn the power switch off.


f.

Turn the power switch on (IG), and wait for at least 60 seconds.


g.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:

Codes other than DTCs B1642, B1643, B1647 and B1648 may be output at this time, but they are not related to this check.



Result:
Result Proceed to
DTC B1642 or B1643 is output. A
DTC B1647 or B1648 is output. B
DTCs B1642, B1643, B1647 and B1648 are not output. C


h.

Turn the power switch off.


i.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



j.

Return the door side airbag sensor RH and LH to their original positions and connect the connectors.



A

B

C

7.CHECK FLOOR WIRE
a.
C284681C19
0.844,0.542 1.229,0.792 0.385,0.25 0.417,2.833 0.813,3.052 0.396,0.219 1.844,1.344 1.844,1.094 false 1.333,1.167 1.771,0.667 false 2.333,1.167 1.917,0.667 false 1.333,2.229 1.333,2.479 false 1.906,1.771 2.073,1.771 2.073,1.771 2.073,2.104 false 0.958,4.302 1.292,3.625 false 1.594,4.313 1.281,3.76 false 0.417,2.083 0.813,2.49 0.396,0.406 10 false *1 2.865,2.094 3.26,2.667 0.396,0.573 10 false *2 1.271,2.479 1.604,2.719 0.333,0.24 10 false *3 1.75,1.698 2.146,2.031 0.396,0.333 10 false *4 1.781,1.354 2.198,1.677 0.417,0.323 10 false *5 0.604,0.167 1,0.583 0.396,0.417 10 false *a 0.156,2.833 0.552,3.24 0.396,0.406 10 false *b 2.542,2.083 2.938,2.656 0.396,0.573 10 false A 2.24,2.083 2.635,2.656 0.396,0.573 10 false B 1.813,2.083 2.208,2.656 0.396,0.573 10 false C 1.521,2.083 1.917,2.656 0.396,0.573 10 false D 1.094,2.083 1.49,2.656 0.396,0.573 10 false E 0.792,2.083 1.188,2.656 0.396,0.573 10 false F 1.177,1.167 1.677,1.5 0.5,0.333 10 false BDR+ 2.198,1.167 2.698,1.5 0.5,0.333 10 false BDR- 0.813,4.313 1.313,4.646 0.5,0.333 10 false BDR+ 1.469,4.313 1.969,4.646 0.5,0.333 10 false BDR- 0.917,0.583 1.417,0.917 0.5,0.333 10 false R33 0.49,2.854 0.99,3.188 0.5,0.333 10 false NR1
*1 Door Side Airbag Sensor RH
*2 Side No. 2 Airbag Sensor RH
*3 Front Door Wire RH
*4 Floor Wire
*5 Service Wire
*a Front view of wire harness connector
(to Side No. 2 Airbag Sensor RH)
*b Front view of wire harness connector
(to Front Door Wire RH)


Disconnect the floor wire connector from the front door wire RH.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Turn the power switch on (IG).


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
NR1-23 (BDR+) - Body ground Power switch on (IG) Below 1 V
NR1-41 (BDR-) - Body ground Power switch on (IG) Below 1 V



e.

Turn the power switch off.


f.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



g.

Using a service wire, connect terminals 1 (BDR+) and 2 (BDR-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
NR1-23 (BDR+) - NR1-41 (BDR-) Always Below 1 Ω



i.

Disconnect the service wire from connector B.


j.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
NR1-23 (BDR+) - NR1-41 (BDR-) Always 1 MΩ or higher
NR1-23 (BDR+) - Body ground Always 1 MΩ or higher
NR1-41 (BDR-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE FRONT DOOR WIRE RH

NG

REPLACE FLOOR WIRE