Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › OCCUPANT CLASSIFICATION SYSTEM
RM33C0E _58 Vehicle Interior _065460 SUPPLEMENTAL RESTRAINT SYSTEMS _0331858 OCCUPANT CLASSIFICATION SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  OCCUPANT CLASSIFICATION SYSTEM  B1785  Front Occupant Classification Sensor LH Collision Detection  


DESCRIPTION

DTC B1785 is stored when the occupant detection ECU receives a collision detection signal sent by the front occupant classification sensor LH in the case of an accident.

DTC B1785 is also stored when the front seat assembly RH is subjected to a strong impact, even if an actual accident did not occur.

If the vehicle was not in a collision, but the occupant detection ECU receives a collision detection signal and stores DTC B1785, the DTC can be cleared by performing zero point calibration. Therefore, if DTC B1785 is output, first perform zero point calibration.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1785 Front Occupant Classification Sensor LH Collision Detection
·

Front occupant classification sensor LH sensed large load.

·

Front seat adjuster assembly RH malfunction


Front occupant classification sensor LH (Front seat adjuster assembly RH)*

*: The front occupant classification sensor LH is built into the front seat adjuster assembly RH.


CAUTION / NOTICE / HINT

NOTICE:
·

When this DTC is stored, repair of the malfunction indicated can only be performed by initializing the occupant detection ECU or replacing the front seat adjuster assembly RH. Do not replace the occupant detection ECU to repair the malfunction indicated by this DTC.

If the occupant detection ECU is replaced, this DTC will not be output but the occupant detection system may not function properly.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



HINT:

When DTC B165A is stored as a result of troubleshooting for the airbag system, check the DTCs stored in the occupant detection ECU. When DTC B1785 is output, perform troubleshooting for this DTC first.


PROCEDURE

1.PERFORM ZERO POINT CALIBRATION
a.

Using the GTS, perform Zero Point Calibration.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION

OK:

"Zero Point Calibration is complete." is displayed.



Result:
Proceed to
OK
NG



OK

2.CHECK DTC

NG

5.REPLACE FRONT SEAT ADJUSTER ASSEMBLY RH
2.CHECK DTC
a.

Turn the power switch on (IG), and wait for at least 60 seconds.


b.

Clear the DTCs stored in the occupant detection ECU.

Body Electrical > Occupant Detection > Clear DTCs
50002 394

c.

Clear the DTCs stored in the airbag sensor assembly.

Body Electrical > SRS Airbag > Clear DTCs
50002 188

d.

Turn the power switch off.


e.

Turn the power switch on (IG), and wait for at least 10 seconds.


f.

Check for DTCs.

Body Electrical > Occupant Detection > Trouble Codes
50001 394
OK:

DTC B1785 is not output.


HINT:

Codes other than DTC B1785 may be output at this time, but they are not related to this check.



g.

Turn the power switch off.


Result:
Proceed to
OK
NG



OK

END

NG

3.REPLACE FRONT SEAT ADJUSTER ASSEMBLY RH
3.REPLACE FRONT SEAT ADJUSTER ASSEMBLY RH
a.

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.


c.

Replace the front seat adjuster assembly RH.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Manual Seat)>REMOVAL


d.

Connect the cable to the negative (-) auxiliary battery terminal.


Result:
Proceed to
NEXT



NEXT

4.PERFORM ZERO POINT CALIBRATION
4.PERFORM ZERO POINT CALIBRATION
a.

Result:
Proceed to
NEXT



NEXT

END

5.REPLACE FRONT SEAT ADJUSTER ASSEMBLY RH
a.

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.


c.

Replace the front seat adjuster assembly RH.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Manual Seat)>REMOVAL


d.

Connect the cable to the negative (-) auxiliary battery terminal.


Result:
Proceed to
NEXT



NEXT

6.PERFORM ZERO POINT CALIBRATION
6.PERFORM ZERO POINT CALIBRATION
a.

Result:
Proceed to
NEXT



NEXT

END