Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.
89831B
1.INSTALL SIDE NO. 2 AIRBAG SENSOR
Check that the power switch is off.
Check that the cable is disconnected from the negative (-) auxiliary battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
Before connecting the connector, check that the position of the white housing lock is as shown in the illustration.
| *a | Correct | *b | Incorrect |
Engage the claw and install the side No. 2 airbag sensor with the bolt.
If the side No. 2 airbag sensor has been dropped, or there are any cracks, dents or other defects in the case or connector, replace it with a new one.
When installing the side No. 2 airbag sensor, make sure that the SRS wiring does not interfere with or is not pinched between other parts.
Make sure that the side No. 2 airbag sensor claw is securely inserted into the body hole.
Connect the connector to the side No. 2 airbag sensor.
| *a | White Housing Lock | - | - |
|
Connect in this Direction | - | - |
When connecting any airbag connector, take care not to damage the airbag wire harness.
Be sure to connect the connector until it is locked (when locking, make sure that a click sound can be heard).
When the connector is locked, the white housing lock will slide. Do not hold the white housing lock or the part (A) as it may result in an insecure connection.
Check that there is no looseness in the installed parts of the side No. 2 airbag sensor.
2.INSTALL REAR SIDE SEATBACK ASSEMBLY
for Fold Down Seat Type: Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for Fold Down Seat Type)>INSTALLATION
for Reclining Seat Type: Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for Reclining Seat Type)>INSTALLATION
62332A
3.CONNECT REAR DOOR OPENING TRIM WEATHERSTRIP
4.INSTALL REAR SEATBACK ASSEMBLY (for Reclining Seat Type)
72996A
5.INSTALL REAR SEATBACK COVER (for Reclining Seat Type)
71940A
6.INSTALL REAR SEAT HEADREST ASSEMBLY (for Reclining Seat Type)
72693
7.INSTALL REAR SEAT CUSHION LOCK HOOK
for Fold Down Seat Type: Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for Fold Down Seat Type)>INSTALLATION
for Reclining Seat Type: Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for Reclining Seat Type)>INSTALLATION
8.INSTALL REAR SEAT CUSHION ASSEMBLY
for Fold Down Seat Type: Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for Fold Down Seat Type)>INSTALLATION
for Reclining Seat Type: Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for Reclining Seat Type)>INSTALLATION
73350C
9.CONNECT REAR CENTER SEAT OUTER BELT ASSEMBLY
for Fold Down Seat Type: Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for Fold Down Seat Type)>INSTALLATION
for Reclining Seat Type: Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for Reclining Seat Type)>INSTALLATION
10.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL
Click hereGeneral>MAINTENANCE>AUXILIARY BATTERY>INSTALLATION
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
64718C
11.INSTALL LUGGAGE TRIM SERVICE HOLE COVER
12. PERFORM DIAGNOSTIC SYSTEM CHECK
13.INSPECT SRS WARNING LIGHT