Home › Vehicle Interior › PRE-COLLISION › PRE-COLLISION SYSTEM › 2017.09–2018.08
RM33C0E _58 Vehicle Interior _065461 PRE-COLLISION _0332154 PRE-COLLISION SYSTEM U

PRE-COLLISION  PRE-COLLISION SYSTEM  TERMINALS OF ECU  


CHECK MILLIMETER WAVE RADAR SENSOR ASSEMBLY


B472993E01
2.219,0.792 2.625,1.01 0.406,0.219 2.302,0.823 2.76,1.021 0.458,0.198 10 false A30

a.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A30-8 (IGB) - A30-1 (SGND) R - W-B Power source Power switch on (IG) 11 to 14 V
A30-1 (SGND) - Body ground W-B - Body ground Ground Always Below 1 Ω


b.

Check for pulses according to the value(s) in the table below.

HINT:

If the waveform is not similar to that shown in the illustration, malfunction of a CAN bus line, terminating resistor or the millimeter wave radar sensor assembly is suspected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A30-3 (CA2H) - A30-1 (SGND) R - W-B CAN communication signal Power switch on (IG) Pulse generation
(See waveform 1)
A30-2 (CA2L) - A30-1 (SGND) W - W-B CAN communication signal Power switch on (IG) Pulse generation
(See waveform 2)
A30-5 (CA1P) - A30-1 (SGND) G - W-B CAN communication signal Power switch on (IG) Pulse generation
(See waveform 1)
A30-6 (CA1N) - A30-1 (SGND) W - W-B CAN communication signal Power switch on (IG) Pulse generation
(See waveform 2)

i.
A086154E97
2.75,0.271 3.365,0.521 0.615,0.25 10 false 1 V/DIV. 1.365,1.906 2.313,2.094 0.948,0.188 10 false 10 μsec./DIV.

Waveform 1

Item Content
Terminal Name Between A30-3 (CA2H) and A30-1 (SGND)
Between A30-5 (CA1P) and A30-1 (SGND)
Tester Range 1 V/DIV., 10 μsec./DIV.
Condition Power switch on (IG)

HINT:

The waveform varies depending on the CAN communication signal.



ii.
A086155E89
2.76,0.281 3.396,0.51 0.635,0.229 10 false 1 V/DIV. 1.365,1.875 2.333,2.073 0.969,0.198 10 false 10 μsec./DIV.

Waveform 2

Item Content
Terminal Name Between A30-2 (CA2L) and A30-1 (SGND)
Between A30-6 (CA1N) and A30-1 (SGND)
Tester Range 1 V/DIV., 10 μsec./DIV.
Condition Power switch on (IG)

HINT:

The waveform varies depending on the CAN communication signal.





CHECK FORWARD RECOGNITION CAMERA


NOTICE:
·

DTCs may be stored when connectors are disconnected during inspection. Therefore, be sure to clear the DTCs using the GTS once the inspection has been completed.

·

Do not apply excessive force to the V6 forward recognition camera connector.



B472992E01
2.073,0.833 2.458,1.042 0.385,0.208 2.188,0.865 2.5,1.063 0.313,0.198 10 false V6

a.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
V6-7 (IGB) - V6-10 (GND) LA-P - LA Power source Power switch on (IG) 11 to 14 V
Power switch off Below 1 V
V6-10 (GND) - Body ground LA - Body ground Ground Always Below 1 Ω


b.

Check for pulses according to the value(s) in the table below.

HINT:

If the waveform is not similar to that shown in the illustration, malfunction of a CAN bus line, terminating resistor or the forward recognition camera is suspected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
V6-5 (CA1P) - V6-10 (GND) L - LA CAN communication signal Power switch on (IG) Pulse generation
(See waveform 1)
V6-11 (CA1N) - V6-10 (GND) W - LA CAN communication signal Power switch on (IG) Pulse generation
(See waveform 2)
V6-6 (CANH) - V6-10 (GND) G - LA CAN communication signal Power switch on (IG) Pulse generation
(See waveform 1)
V6-12 (CANL) - V6-10 (GND) W - LA CAN communication signal Power switch on (IG) Pulse generation
(See waveform 2)

i.
A086154E97
2.75,0.271 3.365,0.521 0.615,0.25 10 false 1 V/DIV. 1.365,1.906 2.313,2.094 0.948,0.188 10 false 10 μsec./DIV.

Waveform 1

Item Content
Terminal Name Between V6-5 (CA1P) and V6-10 (GND)
Between V6-6 (CANH) and V6-10 (GND)
Tester Range 1 V/DIV., 10 μsec./DIV.
Condition Power switch on (IG)

HINT:

The waveform varies depending on the CAN communication signal.



ii.
A086155E89
2.76,0.281 3.396,0.51 0.635,0.229 10 false 1 V/DIV. 1.365,1.875 2.333,2.073 0.969,0.198 10 false 10 μsec./DIV.

Waveform 2

Item Content
Terminal Name Between V6-11 (CA1N) and V6-10 (GND)
Between V6-12 (CANL) and V6-10 (GND)
Tester Range 1 V/DIV., 10 μsec./DIV.
Condition Power switch on (IG)

HINT:

The waveform varies depending on the CAN communication signal.