Home › Vehicle Interior › PRE-COLLISION › PRE-COLLISION SYSTEM › 2017.09–2021.02
RM33C0E _58 Vehicle Interior _065461 PRE-COLLISION _0332154 PRE-COLLISION SYSTEM D

PRE-COLLISION  PRE-COLLISION SYSTEM  FREEZE FRAME DATA  


DESCRIPTION


a.

When a pre-collision system DTC is stored, the millimeter wave radar sensor assembly stores the current vehicle (ECU or sensor) state as Freeze Frame Data.



CHECK FREEZE FRAME DATA


a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Pre-Collision 2 / Trouble Codes.

Body Electrical > Pre-Collision 2 > Trouble Codes
50001 220

e.

According to the GTS display, select a DTC that stored freeze frame data.


f.

Read the freeze frame data recorded when the DTC was stored.

Body Electrical > Pre-Collision 2
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Turn Light RH Turn signal switch (right) status ON or OFF ON: Turn signal switch (right) on
OFF: Turn signal switch (right) off
-
Turn Light LH Turn signal switch (left) status ON or OFF ON: Turn signal switch (left) on
OFF: Turn signal switch (left) off
-
PCS OFF Switch Pre-collision system on/off status ON or OFF ON: Pre-collision system on
OFF: Pre-collision system off
-
Pre-Collision Safety Warning Buz Pre-collision system warning buzzer Valid or Inval Valid: Pre-collision system warning buzzer operation possible
Inval: Pre-collision system warning buzzer operation not possible
-
Pre-Collision Brake Pre-collision braking function Valid or Inval Valid: Pre-collision braking operation possible
Inval: Pre-collision braking operation not possible
-
PBA Start Pre-collision brake assist activation signal OFF, Standby, Assist Lv1 or Assist Lv2 OFF: Pre-collision brake assist not operating
Standby: Brake pedal not depressed during pre-collision brake assist operation
Assist Lv1: Brake pedal depressed during pre-collision brake assist operation
Assist Lv2: Brake pedal firmly depressed during pre-collision brake assist operation
Signal status changes when the pre-collision brake assist is activated before a crash (Pre-collision brake will activate only in situations where the driver depresses the brake pedal)
Brake Assist Standby - - - Not applicable to this vehicle
Pre-Collision Brake Control Pre-collision braking operational status ON or OFF ON: Pre-collision braking operating
OFF: Pre-collision braking not operating
-
AVS Start - - - Not applicable to this vehicle
VGRS Start - - - Not applicable to this vehicle
PBA Control Pre-collision brake assist operational status Valid or Invalid Valid: Pre-collision brake assist control operation possible
Invalid: Pre-collision brake assist control operation not possible
-
Pre-Collision Safety Brake Ind Pre-collision system alarm warning message status ON or OFF ON: Displayed
OFF: Not displayed
"BRAKE!" is displayed
PCS Collision Alarm Buzzer Pre-collision system warning buzzer status ON or OFF ON: Pre-collision system warning buzzer sounding
OFF: Pre-collision system warning buzzer not sounding
-
Front Radar-Low Voltage History Millimeter wave radar sensor assembly low voltage history ON or OFF ON: History of low voltage
OFF: No history of low voltage
If the power switch is turned on (READY) 1 second or more after the power switch is turned on (IG), this item may change to ON.
Front Recognition Camera-Malfunction History Forward recognition camera system unavailable history ON or OFF ON: History of being unavailable
OFF: No history of being unavailable
-
Control Mode ECU control mode status Normal or Check Mode Normal: Normal operation
Check Mode: Operating in control mode
-
PCS Operation State Retention Setting PCS operation state retention setting customize setting ON or OFF ON: Customize setting set to ON
OFF: Customize setting set to OFF
-
PCS Alarm Activation Distance Retention Setting 1 PCS alarm activation distance retention setting 1 customize setting ON or OFF ON: Customize setting set to ON
OFF: Customize setting set to OFF
-
PCS Alarm Activation Distance Retention Setting 2 PCS alarm activation distance retention setting 2 customize setting ON or OFF ON: Customize setting set to ON
OFF: Customize setting set to OFF
-
PCS Alarm Activation Distance Retention Setting 3 PCS alarm activation distance retention setting 3 customize setting ON or OFF ON: Customize setting set to ON
OFF: Customize setting set to OFF
-