Home › Vehicle Interior › PRE-COLLISION › PRE-COLLISION SYSTEM › 2017.09–2021.02
RM33C0E _58 Vehicle Interior _065461 PRE-COLLISION _0332154 PRE-COLLISION SYSTEM C

PRE-COLLISION  PRE-COLLISION SYSTEM  U0235  Lost Communication with Cruise Control Front Distance Range Sensor  


DESCRIPTION

The millimeter wave radar sensor assembly is connected to the skid control ECU (brake booster with master cylinder assembly) via CAN communication. If communication with the skid control ECU (brake booster with master cylinder assembly) stops, the millimeter wave radar sensor assembly stores DTC U0235.

DTC No. Detection Item DTC Detection Condition Trouble Area
U0235 Lost Communication with Cruise Control Front Distance Range Sensor When the power switch is on (IG), a communication error between the millimeter wave radar sensor assembly and skid control ECU (brake booster with master cylinder assembly) is detected for approximately 2 seconds.
·

Electronically controlled brake system

·

Millimeter wave radar sensor assembly



CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the millimeter wave radar sensor assembly, always replace it with a new one. If a millimeter wave radar sensor assembly which was installed to another vehicle is used, the information stored in the millimeter wave radar sensor assembly will not match the information from the vehicle. As a result, a DTC may be stored.

·

If the millimeter wave radar sensor assembly has been replaced, be sure to perform millimeter wave radar sensor assembly adjustment.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT

·

The pre-collision system uses the CAN communication system. First, confirm that there are no malfunctions in the CAN communication system. Refer to How to Proceed with Troubleshooting.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING



PROCEDURE

1.CHECK FOR DTCs (ELECTRONICALLY CONTROLLED BRAKE SYSTEM)
a.

Check for DTCs.

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
Electronically controlled brake system DTCs are not output A
Electronically controlled brake system DTCs are output B



A

2.TEST MODE INSPECTION (ELECTRONICALLY CONTROLLED BRAKE SYSTEM)

B

2.TEST MODE INSPECTION (ELECTRONICALLY CONTROLLED BRAKE SYSTEM)
HINT:

When entering Test Mode (Signal Check), the skid control ECU (brake booster with master cylinder assembly) communicates with the millimeter wave radar sensor assembly to judge whether the vehicle is equipped with the pre-collision system. Therefore, do not exit Test Mode (Signal Check) within 5 seconds of entering Test Mode (Signal Check).


a.

Procedure to Enter Test Mode (Signal Check)

i.

Turn the power switch off.


ii.

Check that the steering wheel is centered.


iii.

Check that park (P) is selected.


iv.

Connect the GTS to the DLC3.


v.

Turn the power switch on (IG).


vi.

Turn the GTS on.


vii.

Switch the skid control ECU (brake booster with master cylinder assembly) to Test Mode (Signal Check) using the GTS. Enter the following menus: Chassis / ABS/VSC/TRC / Utility / Signal Check.

HINT:

Do not exit Test Mode (Signal Check) within 5 seconds of entering Test Mode (Signal Check). If Test Mode (Signal Check) is exited within 5 seconds of entering Test Mode (Signal Check), DTC U0235 may be stored. If DTC U0235 is output after exiting Test Mode (Signal Check), enter Test Mode (Signal Check) again, wait at least 5 seconds, then recheck for DTCs.


Chassis > ABS/VSC/TRC > Utility
Tester Display
Signal Check
50005 105 4359


b.

Test Mode (Signal Check) Display Check

i.

Check that the ABS warning, brake warning / yellow (minor malfunction) and slip indicator lights come on for several seconds and then blink in the Test Mode pattern.

HINT:

If the ABS warning light, brake warning light / yellow (minor malfunction) or slip indicator light remains illuminated or does not illuminate when Test Mode (Signal Check) is entered, a component or wire harness may be malfunctioning.




c.

End Test Mode (Signal Check)

i.

Turn the power switch off and disconnect the GTS.



Result:
Proceed to
NEXT



NEXT

3.CHECK FOR DTCs (PRE-COLLISION SYSTEM)
3.CHECK FOR DTCs (PRE-COLLISION SYSTEM)
a.

Clear the DTCs.

Body Electrical > Pre-Collision 2 > Clear DTCs
50002 220

b.

Perform the following procedure.

HINT:

If the following procedure is not performed, the previously output DTC cannot be detected.

1.

Turn the power switch on (IG) and wait 2 seconds or more.




c.

Check for DTCs.

Body Electrical > Pre-Collision 2 > Trouble Codes
50001 220

Result:
Result Proceed to
DTC U0235 is not output A
DTC U0235 is output B



A

END

B

REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY