DTC U1002 is stored when the millimeter wave radar sensor assembly cannot receive signals from the forward recognition camera.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| U1002 | Lost Communication with Gateway Module | After the power switch is turned on (IG), communication between the millimeter wave radar sensor assembly and forward recognition camera is abnormal for 2 seconds or more. | ·
CAN bus line or connector ·
Forward recognition camera ·
Millimeter wave radar sensor assembly |
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle. As a result, a DTC may be stored.
If the forward recognition camera has been replaced with a new one, be sure to perform forward recognition camera adjustment.
Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (SEQUENTIAL RECOGNITION)
When replacing the millimeter wave radar sensor assembly, always replace it with a new one. If a millimeter wave radar sensor assembly which was installed to another vehicle is used, the information stored in the millimeter wave radar sensor assembly will not match the information from the vehicle. As a result, a DTC may be stored.
If the millimeter wave radar sensor assembly has been replaced, be sure to perform millimeter wave radar sensor assembly adjustment.
Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT
Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.
When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
| *a | Component with harness connected
(Millimeter Wave Radar Sensor Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Result |
|---|---|---|---|
| A30-5 (CA1P) - A30-6 (CA1N) | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω | Below 54 Ω:
Short circuit between CAN bus lines |
| 70 Ω or more:
Open circuit in a CAN bus line |
|||
| A30-5 (CA1P) - A30-1 (SGND) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher | Below 200 Ω:
Ground short |
| A30-6 (CA1N) - A30-1 (SGND) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher | Below 200 Ω:
Ground short |
| A30-5 (CA1P) - A30-8 (IGB) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher | Below 6 kΩ:
+B short |
| A30-6 (CA1N) - A30-8 (IGB) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher | Below 6 kΩ:
+B short |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (Open circuit in CAN bus line) | B |
| NG (Short circuit between CAN bus lines) | C |
| NG (Short to +B or ground) | D |
A
B
C
D
Clear the DTCs.
Perform the following procedure.
If the following procedure is not performed, the previously output DTC cannot be detected.
Turn the power switch on (IG) and wait 2 seconds or more.
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTC U1002 is not output | A |
| DTC U1002 is output | B |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
Disconnect the V6 forward recognition camera connector.
Disconnect the A30 millimeter wave radar sensor assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| V6-6 (CANH) - A30-5 (CA1P) | Cable disconnected from negative (-) auxiliary battery terminal | Below 1 Ω |
| V6-12 (CANL) - A30-6 (CA1N) | Cable disconnected from negative (-) auxiliary battery terminal | Below 1 Ω |
Connect the A30 millimeter wave radar sensor assembly connector.
Connect the V6 forward recognition camera connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Forward Recognition Camera) |
Disconnect the V6 forward recognition camera connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| V6-6 (CANH) - V6-12 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
Connect the V6 forward recognition camera connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Forward Recognition Camera) |
Disconnect the V6 forward recognition camera connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| V6-6 (CANH) - V6-12 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
Connect the V6 forward recognition camera connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly) |
Disconnect the A30 millimeter wave radar sensor assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A30-5 (CA1P) - A30-6 (CA1N) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
Connect the A30 millimeter wave radar sensor assembly connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the V6 forward recognition camera connector.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to Forward Recognition Camera) |
- | - |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| V6-6 (CANH) - K68-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| V6-12 (CANL) - K68-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| V6-6 (CANH) - K68-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| V6-12 (CANL) - K68-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
Connect the V6 forward recognition camera connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A30 millimeter wave radar sensor assembly connector.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly) |
- | - |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A30-5 (CA1P) - K68-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A30-6 (CA1N) - K68-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A30-5 (CA1P) - K68-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| A30-6 (CA1N) - K68-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
Connect the A30 millimeter wave radar sensor assembly connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG