Home › Vehicle Interior › SEAT BELT › SEAT BELT WARNING SYSTEM (w/ Occupant Classification System)
RM33C0E _58 Vehicle Interior _065463 SEAT BELT _0332564 SEAT BELT WARNING SYSTEM(w/ Occupant Classification System) J

SEAT BELT  SEAT BELT WARNING SYSTEM(w/ Occupant Classification System)  Rear Seat Belt Warning Light Malfunction  


DESCRIPTION

The main body ECU (multiplex network body ECU) detects whether either the rear doors are open or closed based on the courtesy light switch condition and then sends the rear door status signal to the combination meter assembly. The combination meter assembly detects rear seat belt state. The rear seat belt warning light on the telltale light assembly illuminates, blinks or turns off in accordance with the rear door state, vehicle speed and rear seat belt state.

WIRING DIAGRAM

B472024E04
1.917,0.25 2.354,0.458 0.438,0.208 10 false RLMT 1.896,0.677 2.333,0.865 0.438,0.188 10 false RCMT 1.906,1.104 2.354,1.344 0.448,0.24 10 false RRMT 1.917,2.573 2.375,2.792 0.458,0.219 10 false RLSB 1.906,3.094 2.406,3.281 0.5,0.188 10 false RCSB 1.896,4.323 2.365,4.51 0.469,0.188 10 false RRSB 3.729,0.365 4.646,0.563 0.917,0.198 10 false RLID 3.729,0.781 4.646,0.979 0.917,0.198 10 false RCID 3.729,1.24 4.646,1.438 0.917,0.198 10 false RRID 5.625,0.938 6.198,1.333 0.573,0.396 10 false ECU-IG1 NO. 4 3.698,1.542 4.615,1.74 0.917,0.198 10 false K36 3.708,1.698 5.771,1.917 2.063,0.219 10 false Telltale Light Assembly 3.417,2.677 3.76,2.875 0.344,0.198 10 false R73 3.396,3.208 3.75,3.406 0.354,0.198 10 false R74 3.198,3.708 6.073,3.948 2.875,0.24 10 false Rear Seat Inner with Center Belt Assembly LH 3.188,4.698 4.104,4.896 0.917,0.198 10 false R72 3.188,4.865 6.396,5.135 3.208,0.271 10 false Rear Seat Inner with Center Belt Assembly RH 3.188,5.854 3.771,6.094 0.583,0.24 10 false R7 3.188,6 6.635,6.24 3.448,0.24 10 false Rear Door Courtesy Light Switch Assembly (LH) 3.208,6.792 4.125,6.99 0.917,0.198 10 false R6 3.208,6.927 6.542,7.167 3.333,0.24 10 false Rear Door Courtesy Light Switch Assembly (RH) 1.115,5.646 2.031,5.844 0.917,0.198 10 false LCTY 1.104,6.542 2.021,6.74 0.917,0.198 10 false RCTY 0.333,7.063 0.635,7.302 0.302,0.24 10 false MB 0.323,7.24 1.479,7.896 1.156,0.656 10 false Main Body ECU (Multiplex Network Body ECU) 1.042,8.385 4,8.604 2.958,0.219 10 false : CAN Communication Line 1.583,6.417 1.771,6.625 0.188,0.208 10 false 2 1.552,5.563 1.896,5.771 0.344,0.208 10 false 13 3.573,0.26 3.917,0.469 0.344,0.208 10 false 1 3.573,0.677 3.917,0.885 0.344,0.208 10 false 2 3.573,1.115 3.917,1.323 0.344,0.208 10 false 3 5.313,0.667 5.656,0.875 0.344,0.208 10 false 10 6.469,0.781 7.115,1.51 0.646,0.729 10 false from IG1-NO. 1 Relay 3.49,2.479 3.688,2.646 0.198,0.167 10 false 5 5.417,2.479 5.573,2.656 0.156,0.177 10 false 4 3.479,3.01 3.677,3.229 0.198,0.219 10 false 1 5.417,3.01 5.604,3.177 0.188,0.167 10 false 2 3.552,4.333 3.896,4.542 0.344,0.208 10 false 5 5.333,4.323 5.677,4.531 0.344,0.208 10 false 4 3.542,5.573 3.885,5.781 0.344,0.208 10 false 1 3.542,6.417 3.885,6.625 0.344,0.208 10 false 1 2.365,0.25 2.708,0.458 0.344,0.208 10 false 18 2.365,0.677 2.708,0.885 0.344,0.208 10 false 19 2.385,1.115 2.729,1.323 0.344,0.208 10 false 20 2.396,2.531 2.646,2.729 0.25,0.198 10 false 24 2.385,3.073 2.646,3.25 0.26,0.177 10 false 25 2.396,4.323 2.74,4.531 0.344,0.208 10 false 26 5.042,0.771 5.958,0.969 0.917,0.198 10 false IG+ 0.604,4.969 4.583,5.167 3.979,0.198 10 false Combination Meter Assembly 0.604,4.833 1.063,5.031 0.458,0.198 10 false K21 1.563,6.896 2.781,7.448 1.219,0.552 10 false Instrument Panel Junction Block Assembly 1.906,5.667 2.219,5.865 0.313,0.198 10 false 3D 1.917,6.531 2.229,6.729 0.313,0.198 10 false 3A 1.927,6.333 2.115,6.542 0.188,0.208 10 false 31 1.906,5.49 2.219,5.688 0.313,0.198 10 false 24 5.354,2.667 5.698,2.865 0.344,0.198 10 false R73 4.292,2.813 4.813,3.031 0.521,0.219 10 false (for LH) 5.344,3.198 5.698,3.396 0.354,0.198 10 false R74 4.188,3.333 5,3.552 0.813,0.219 10 false (for Center) 1.635,2.292 1.875,2.479 0.24,0.188 10 false IG 4.906,4.365 5.333,4.573 0.427,0.208 10 false RBR- 3.729,4.365 4.156,4.573 0.427,0.208 10 false RBR+ 4.917,2.583 5.344,2.792 0.427,0.208 10 false LBR- 4.917,3.104 5.344,3.313 0.427,0.208 10 false CBR- 3.74,2.583 4.167,2.792 0.427,0.208 10 false LBR+ 3.74,3.104 4.167,3.313 0.427,0.208 10 false CBR+

CAUTION / NOTICE / HINT

NOTICE:
·

The seat belt warning system (w/ occupant classification system) uses the CAN communication system. First, confirm that there is no malfunction in the CAN communication system. Refer to the How to Proceed with Troubleshooting procedure.

Click hereVehicle Interior>SEAT BELT>SEAT BELT WARNING SYSTEM (w/ Occupant Classification System)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.READ VALUE USING GTS (RR DOOR COURTESY SW, RL DOOR COURTESY SW)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RR Door Courtesy SW Rear door courtesy light switch RH ON or OFF ON: Rear door RH open
OFF: Rear door RH closed
-
RL Door Courtesy SW Rear door courtesy light switch LH ON or OFF ON: Rear door LH open
OFF: Rear door LH closed
-
Body Electrical > Main Body > Data List
Tester Display
RR Door Courtesy SW
RL Door Courtesy SW
50003 123 24,25
OK:

The GTS display changes correctly in response to the rear door condition.



Result:
Proceed to
OK
NG



OK

2.CHECK REAR SEAT BELT WARNING

NG

2.CHECK REAR SEAT BELT WARNING
a.
B489643C02
0.813,1.635 0.813,1.302 false 2.594,1.635 2.594,1.302 false 1.708,1.656 1.708,1.323 false 0.75,1.635 1.063,1.833 0.313,0.198 10 false *a 1.677,1.667 1.99,1.865 0.313,0.198 10 false *b 2.552,1.635 2.865,1.833 0.313,0.198 10 false *c 0.198,0.156 0.51,0.354 0.313,0.198 10 false *1
*1 Rear Seat Belt Warning Light (Telltale Light Assembly)
*a LH
*b Center
*c RH


Check the rear seat belt warning function.

Click hereVehicle Interior>SEAT BELT>SEAT BELT WARNING SYSTEM (w/ Occupant Classification System)>ON-VEHICLE INSPECTION


Result:
Result Proceed to
The rear seat belt warning lights operation is normal A
The rear seat belt warning lights (all seats) do not operate normally B
The rear seat belt warning light (RH) does not operate normally C
The rear seat belt warning light (center) does not operate normally D
The rear seat belt warning light (LH) does not operate normally E



A

B

3.PERFORM ACTIVE TEST USING GTS (REAR SEAT BELT WARNING)

C

6.READ VALUE USING GTS (REAR RIGHT SEAT BUCKLE / OCCUPANT DETECTION WARNING SWITCH)

D

10.READ VALUE USING GTS (REAR CENTER SEAT BUCKLE / OCCUPANT DETECTION WARNING SWITCH)

E

14.READ VALUE USING GTS (REAR LEFT SEAT BUCKLE / OCCUPANT DETECTION WARNING SWITCH)
3.PERFORM ACTIVE TEST USING GTS (REAR SEAT BELT WARNING)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Combination Meter > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Rear Seat Belt Warning Rear seat belt warning light OFF/ON -
Body Electrical > Combination Meter > Active Test
Tester Display
Rear Seat Belt Warning
50004 409 44

Result:
Result Proceed to
The rear seat belt warning light does not operate normally A
The rear seat belt warning light operates normally B



A

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE)

B

REPLACE COMBINATION METER ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE)
a.

Disconnect the K36 telltale light assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
K36-10 (IG+) - Body ground Power switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (TELLTALE LIGHT ASSEMBLY - COMBINATION METER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (TELLTALE LIGHT ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Reconnect the K36 telltale light assembly connector.


b.

Disconnect the K21 combination meter assembly connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
K21-18 (RLMT) - Body ground Power switch on (IG) 11 to 14 V
K21-19 (RCMT) - Body ground Power switch on (IG) 11 to 14 V
K21-20 (RRMT) - Body ground Power switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPLACE TELLTALE LIGHT ASSEMBLY

6.READ VALUE USING GTS (REAR RIGHT SEAT BUCKLE / OCCUPANT DETECTION WARNING SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Combination Meter > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Rear Right Seat Buckle / Occupant Detection Warning Switch Rear seat inner with center belt RH buckle signal ON or OFF OFF: Rear RH seat belt fastened
ON: Rear RH seat belt not fastened
-
Body Electrical > Combination Meter > Data List
Tester Display
Rear Right Seat Buckle / Occupant Detection Warning Switch
50003 409 30

Result:
Result Proceed to
ON or OFF does not appear on the tester screen according to the rear seat belt condition A
ON or OFF appears on the tester screen according to the rear seat belt condition B



A

7.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - REAR SEAT INNER WITH CENTER BELT ASSEMBLY RH - BODY GROUND)

B

8.PERFORM ACTIVE TEST USING GTS (REAR SEAT BELT WARNING)
7.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - REAR SEAT INNER WITH CENTER BELT ASSEMBLY RH - BODY GROUND)
a.

Disconnect the K21 combination meter assembly connector.


b.

Disconnect the R72 rear seat inner with center belt assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K21-26 (RRSB) - R72-5 Always Below 1 Ω
K21-26 (RRSB) or R72-5 - Body ground Always 10 kΩ or higher
R72-4 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE REAR SEAT INNER WITH CENTER BELT ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.PERFORM ACTIVE TEST USING GTS (REAR SEAT BELT WARNING)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Combination Meter > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Rear Seat Belt Warning Rear seat belt warning light OFF/ON -
Body Electrical > Combination Meter > Active Test
Tester Display
Rear Seat Belt Warning
50004 409 44

Result:
Result Proceed to
The rear seat belt warning light does not operate normally A
The rear seat belt warning light operates normally B



A

9.CHECK HARNESS AND CONNECTOR (TELLTALE LIGHT ASSEMBLY - COMBINATION METER ASSEMBLY)

B

REPLACE COMBINATION METER ASSEMBLY

9.CHECK HARNESS AND CONNECTOR (TELLTALE LIGHT ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Disconnect the K21 combination meter assembly connector.


b.

Disconnect the K36 telltale light assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K21-20 (RRMT) - K36-3 (RRID) Always Below 1 Ω
K21-20 (RRMT) or K36-3 (RRID) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE TELLTALE LIGHT ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.READ VALUE USING GTS (REAR CENTER SEAT BUCKLE / OCCUPANT DETECTION WARNING SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Combination Meter > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Rear Center Seat Buckle / Occupant Detection Warning Switch Rear seat inner with center belt LH (for center) buckle signal ON or OFF OFF: Rear LH seat belt (for center) fastened
ON: Rear LH seat belt (for center) not fastened
-
Body Electrical > Combination Meter > Data List
Tester Display
Rear Center Seat Buckle / Occupant Detection Warning Switch
50003 409 32

Result:
Result Proceed to
ON or OFF does not appear on the tester screen according to the rear seat belt condition A
ON or OFF appears on the tester screen according to the rear seat belt condition B



A

11.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH (FOR CENTER) - BODY GROUND)

B

12.PERFORM ACTIVE TEST USING GTS (REAR SEAT BELT WARNING)
11.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH (FOR CENTER) - BODY GROUND)
a.

Disconnect the K21 combination meter assembly connector.


b.

Disconnect the R74 rear seat inner with center belt assembly LH (for center) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K21-25 (RCSB) - R74-1 Always Below 1 Ω
K21-25 (RCSB) or R74-1 - Body ground Always 10 kΩ or higher
R74-2 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.PERFORM ACTIVE TEST USING GTS (REAR SEAT BELT WARNING)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Combination Meter > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Rear Seat Belt Warning Rear seat belt warning light OFF/ON -
Body Electrical > Combination Meter > Active Test
Tester Display
Rear Seat Belt Warning
50004 409 44

Result:
Result Proceed to
The rear seat belt warning light does not operate normally A
The rear seat belt warning light operates normally B



A

13.CHECK HARNESS AND CONNECTOR (TELLTALE LIGHT ASSEMBLY - COMBINATION METER ASSEMBLY)

B

REPLACE COMBINATION METER ASSEMBLY

13.CHECK HARNESS AND CONNECTOR (TELLTALE LIGHT ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Disconnect the K21 combination meter assembly connector.


b.

Disconnect the K36 telltale light assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K21-19 (RCMT) - K36-2 (RCID) Always Below 1 Ω
K21-19 (RCMT) or K36-2 (RCID) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE TELLTALE LIGHT ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.READ VALUE USING GTS (REAR LEFT SEAT BUCKLE / OCCUPANT DETECTION WARNING SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Combination Meter > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Rear Left Seat Buckle / Occupant Detection Warning Switch Rear seat inner with center belt LH (for LH) buckle signal ON or OFF OFF: Rear LH seat belt (for LH) fastened
ON: Rear LH seat belt (for LH) not fastened
-
Body Electrical > Combination Meter > Data List
Tester Display
Rear Left Seat Buckle / Occupant Detection Warning Switch
50003 409 31

Result:
Result Proceed to
ON or OFF does not appear on the tester screen according to the rear seat belt condition A
ON or OFF appears on the tester screen according to the rear seat belt condition B



A

15.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH (FOR LH) - BODY GROUND)

B

16.PERFORM ACTIVE TEST USING GTS (REAR SEAT BELT WARNING)
15.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH (FOR LH) - BODY GROUND)
a.

Disconnect the K21 combination meter assembly connector.


b.

Disconnect the R73 rear seat inner with center belt assembly LH (for LH) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K21-24 (RLSB) - R73-5 Always Below 1 Ω
K21-24 (RLSB) or R73-5 - Body ground Always 10 kΩ or higher
R73-4 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.PERFORM ACTIVE TEST USING GTS (REAR SEAT BELT WARNING)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Combination Meter > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Rear Seat Belt Warning Rear seat belt warning light OFF/ON -
Body Electrical > Combination Meter > Active Test
Tester Display
Rear Seat Belt Warning
50004 409 44

Result:
Result Proceed to
The rear seat belt warning light does not operate normally A
The rear seat belt warning light operates normally B



A

17.CHECK HARNESS AND CONNECTOR (TELLTALE LIGHT ASSEMBLY - COMBINATION METER ASSEMBLY)

B

REPLACE COMBINATION METER ASSEMBLY

17.CHECK HARNESS AND CONNECTOR (TELLTALE LIGHT ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Disconnect the K21 combination meter assembly connector.


b.

Disconnect the K36 telltale light assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K21-18 (RLMT) - K36-1 (RLID) Always Below 1 Ω
K21-18 (RLMT) or K36-1 (RLID) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE TELLTALE LIGHT ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR