Home › Vehicle Interior › SEAT BELT › FRONT SEAT OUTER BELT ASSEMBLY › 2017.09–2019.02
RM33C0E _58 Vehicle Interior _065463 SEAT BELT _0332569 FRONT SEAT OUTER BELT ASSEMBLY A

SEAT BELT  FRONT SEAT OUTER BELT ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during front seat outer belt assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative auxiliary battery terminal Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control) (Click here)
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)

CAUTION:
·

Wear protective gloves. Sharp areas on the parts may injure your hands.

·
B401522

Be sure to read Precaution thoroughly before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION



HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 64718C 2.REMOVE LUGGAGE TRIM SERVICE HOLE COVER

Hide 3.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Click hereGeneral>MAINTENANCE>AUXILIARY BATTERY>REMOVAL

CAUTION:
B422343

·

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

·

If an airbag deploys for any reason, it may cause a serious injury.



Hide 67914 4.REMOVE FRONT DOOR SCUFF PLATE

Hide 62312B 5.DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP

a.

Disconnect the front door opening trim weatherstrip.


Hide 67918A 6.REMOVE REAR DOOR SCUFF PLATE

Hide 62332A 7.DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP

a.

Disconnect the rear door opening trim weatherstrip.


Hide 73233 8.REMOVE LAP BELT OUTER ANCHOR COVER

a.
B470196

Disengage the 3 claws to remove the lap belt outer anchor cover.


Hide 73220 9.DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY

a.
B470197

Remove the bolt to disconnect the floor anchor of the front seat outer belt assembly.


Hide 62414A 10.REMOVE LOWER CENTER PILLAR GARNISH

Hide 62412B 11.REMOVE UPPER CENTER PILLAR GARNISH

Hide 73220 12.REMOVE FRONT SEAT OUTER BELT ASSEMBLY

a.
B470199

Remove the nut and disconnect the shoulder anchor of the front seat outer belt assembly.


b.
B470200C01
1.229,0.802 1.49,0.458 true 0.646,1.01 0.906,0.667 true 1.521,0.365 1.833,0.521 0.313,0.156 10 false *a 0.479,0.927 0.792,1.083 0.313,0.156 10 false *b 1.031,0.25 1.344,0.406 0.313,0.156 10 false *c
*a Protective Tape
*b Locking Button
*c Release


Using a screwdriver, pull out the locking button as shown in the illustration to release the lock and disconnect the pretensioner connector.

HINT:

Tape the screwdriver tip before use.



c.
B470201

Remove the 2 bolts.


d.

Disengage the 2 guides to remove the front seat outer belt assembly.


Hide 73200A 13.REMOVE FRONT SHOULDER BELT ANCHOR ADJUSTER ASSEMBLY

a.
B470198

Remove the 2 bolts.


b.

Disengage the guide to remove the front shoulder belt anchor adjuster assembly.