The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during rear seat outer belt assembly removal/installation are shown below.
Wear protective gloves. Sharp areas on the parts may injure your hands.
Be sure to read Precaution thoroughly before servicing.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION
1. PRECAUTION
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
64718C
2.REMOVE LUGGAGE TRIM SERVICE HOLE COVER
3.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
Click hereGeneral>MAINTENANCE>AUXILIARY BATTERY>REMOVAL
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
If an airbag deploys for any reason, it may cause a serious injury.
73350C
4.DISCONNECT REAR CENTER SEAT OUTER BELT ASSEMBLY (for Fold Down Seat Type)
5.REMOVE REAR SEAT CUSHION ASSEMBLY (for Fold Down Seat Type)
72693
6.REMOVE REAR SEAT CUSHION LOCK HOOK (for Fold Down Seat Type)
62332A
7.DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP LH (for Fold Down Seat Type)
8.REMOVE REAR SIDE SEATBACK ASSEMBLY LH (for Fold Down Seat Type)
62331A
9.DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP RH (for Fold Down Seat Type)
Use the same procedure as for the LH side.
10.REMOVE REAR SIDE SEATBACK ASSEMBLY RH (for Fold Down Seat Type)
Use the same procedure as for the LH side.
11.REMOVE REAR SEAT ASSEMBLY (for Reclining Seat Type)
62472A
12.REMOVE INNER ROOF SIDE GARNISH LH
62471A
13.REMOVE INNER ROOF SIDE GARNISH RH
Use the same procedure as for the LH side.
73370E
14.DISCONNECT REAR SEAT OUTER BELT ASSEMBLY LH
Remove the bolt to disconnect the floor anchor of the rear seat outer belt assembly LH.
73360D
15.DISCONNECT REAR SEAT OUTER BELT ASSEMBLY RH
Use the same procedure as for the LH side.
81006
16.REMOVE CENTER STOP LIGHT SET
73373F
17.REMOVE REAR SEAT SHOULDER BELT HOLE COVER
Disengage the 2 claws and 2 guides to remove the rear seat shoulder belt hole cover.
Use the same procedure for the other rear seat shoulder belt hole covers.
64330
18.REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY (w/o Rear Sunshade)
Fold the rear seatback assembly LH and rear seatback assembly RH forward.
Remove the 2 clips.
Disengage the 3 clips and 5 guides.
Pass the 3 rear seat belt floor anchors through the package tray trim panel assembly then remove the package tray trim panel assembly.
64330
19.REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY (w/ Rear Sunshade)
Disengage the 3 clips.
Pass the 3 rear seat belt floor anchors through the package tray trim panel assembly then remove the package tray trim panel assembly.
73370E
20.REMOVE REAR SEAT OUTER BELT ASSEMBLY LH
| *a | Protective Tape |
| *b | Locking Button |
| *c | Release |
Using a screwdriver, pull out the locking button as shown in the illustration to release the lock and disconnect the pretensioner connector.
Tape the screwdriver tip before use.
Remove the 2 bolts.
Disengage the guide to remove the rear seat outer belt assembly LH.
73360D
21.REMOVE REAR SEAT OUTER BELT ASSEMBLY RH
Use the same procedure as for the LH side.
73432
22.REMOVE REAR SEAT BELT RETRACTOR COVER
|
Remove in this Direction |
Remove the rear seat belt retractor cover as shown in the illustration.
Use the same procedure for the RH side and LH side.