Home › Vehicle Exterior › WIPER / WASHER › FRONT WIPER MOTOR
RM33C0E _59 Vehicle Exterior _065471 WIPER / WASHER _0332907 FRONT WIPER MOTOR A

WIPER / WASHER  FRONT WIPER MOTOR  REMOVAL  


CAUTION / NOTICE / HINT

NOTICE:

Make sure to hold the front wiper arm while lifting it as lifting the front wiper arm by the front wiper blade may damage or deform the front wiper blade.


PROCEDURE

Hide 85292B 1.REMOVE FRONT WIPER ARM HEAD CAP

a.
E364776C01
1.625,0.865 2.01,0.875 true 2.01,0.781 2.208,0.948 0.198,0.167 10 true *a
*a Protective Tape


Using a screwdriver, disengage the 3 claws to remove the front wiper arm head cap.

HINT:
·

Tape the screwdriver tip before use.

·

Use the same procedure for the RH side and LH side.




Hide 2.REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH

a.
E364777

Remove the nut and front wiper arm and blade assembly LH.


Hide 3.REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH

a.
E364778

Remove the nut and front wiper arm and blade assembly RH.


Hide 53867H 4.REMOVE FRONT FENDER TO COWL SIDE SEAL LH

a.
E364800

Disengage the 3 claws and 2 guides to remove the front fender to cowl side seal LH.


Hide 53866J 5.REMOVE FRONT FENDER TO COWL SIDE SEAL RH

E364801

a.

Disengage the 3 claws and 2 guides to remove the front fender to cowl side seal RH.


Hide 55708 6.REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

NOTICE:

To prevent damage to the windshield glass, remove any foreign matter (sand, dust, etc.) from around the contacting surfaces of the cowl top ventilator louver sub-assembly and windshield glass.


a.

Remove the 2 clips.

E374982


b.

Close the hood sub-assembly.


c.
E369039C01
2.01,1.979 2.677,1.792 true 2.688,1.677 3,1.833 0.313,0.156 10 false *a 0.958,1.646 1.115,1.844 0.156,0.198 10 false A
*a Edge of Protective Tape
V100155

Protective Tape


Apply protective tape to a moulding remover as shown in the illustration.

Standard Dimension:
Area Dimension
A 4.0 mm (0.157 in.)



d.

Insert the moulding remover at the starting position until the edge of the protective tape is aligned with the cowl top ventilator louver sub-assembly as shown in the illustration.

E364851C01
1.375,1.167 1.771,1.302 true 3.781,0.708 4.177,0.844 true 1.073,3.677 1.375,3.781 true 2.292,0.635 2.469,0.479 true 4.49,1.552 4.875,1.135 true 1.188,1.073 1.375,1.24 0.188,0.167 10 true *a 4.833,0.969 5.031,1.135 0.198,0.167 10 true *b 0.854,2.99 1.167,3.156 0.313,0.167 10 false *c 3.042,2.99 3.333,3.167 0.292,0.177 10 false *d 2.49,0.323 2.802,0.479 0.313,0.156 10 false *f 0.885,3.573 1.073,3.74 0.188,0.167 10 true *a 3.583,0.604 3.771,0.771 0.188,0.167 10 true *a 5.177,2.979 5.469,3.156 0.292,0.177 10 false *e
*a Starting Position:
Side of Cowl Top Ventilator Louver Sub-assembly and Moulding Remover Aligned
*b Inserted to Edge of Protective Tape
*c Not Inserted at Starting Position *d Not Inserted to Edge of Protective Tape
*e Not Inserted Straight *f Piece of Cloth or Equivalent
V100155

Protective Tape - -


NOTICE:
·

To prevent damage to the windshield glass, set a piece of cloth between the moulding remover and windshield glass.


·

Make sure to insert the moulding remover until the edge of protective tape is aligned with the cowl top ventilator louver sub-assembly, otherwise the cowl top ventilator louver sub-assembly may be deformed or damaged.




e.

While pushing the moulding remover in the direction indicated by the arrow (A), push the moulding remover in the direction indicated by the arrow (B) to disengage the cowl top ventilator louver sub-assembly.

E364850C01
0,0 0,0 false
V113147

Push in this Direction (A)
V113148

Push in this Direction (B)


NOTICE:
·

Make sure to repeat this procedure to disengage the entire cowl top ventilator louver sub-assembly.


·

Make sure to perform this procedure while pushing the moulding remover in the direction indicated by the arrow (A), otherwise the cowl top ventilator louver sub-assembly may be deformed or damaged.


·

Make sure not to pry the cowl top ventilator louver sub-assembly more than necessary to disengage it, otherwise it may be deformed or damaged.

E369631C01
4.333,0.927 4.646,1.083 0.313,0.156 10 false *b 0.542,0.917 0.854,1.073 0.313,0.156 10 false *a
*a Pried Until Disengaged *b Pried Excessively





f.

Using the moulding remover, repeatedly pry up the cowl top ventilator louver sub-assembly while gradually moving the moulding remover half of its width laterally toward the center of the vehicle and then repeat the procedure from the other side of the vehicle as shown in the illustration to disengage the cowl top ventilator louver sub-assembly from the windshield glass.

E364852C01
1.115,2.156 1.302,2.333 0.188,0.177 10 true *a 4.698,2.25 4.885,2.427 0.188,0.177 10 true *a
*a Half Width of Moulding Remover - -
V100136

Order of Removal - -


NOTICE:
·

Make sure to move the moulding remover only half of its width laterally after prying up the cowl top ventilator louver sub-assembly, otherwise the cowl top ventilator louver sub-assembly may be damaged or deformed.

·

Make sure not to lift up or pull the cowl top ventilator louver sub-assembly by hand before it is completely disengaged, otherwise it may be deformed or damaged.




g.

Open the hood sub-assembly.


h.

Disengage the 4 claws and guide as shown in the illustration.

E374983C01
0,0 0,0 false
V113147

Remove in this Direction - -



i.

Pull the passenger side of the cowl top ventilator louver sub-assembly as shown in the illustration.

E374984C01
0,0 0,0 false
V113147

Remove in this Direction - -



j.

Lift the front of the cowl top ventilator louver sub-assembly as shown in the illustration.

E374985C01
6.021,4.938 6.229,5.271 6.229,5.271 6.469,5.031 true 6.156,5.281 6.354,5.479 0.198,0.198 10 true *a
*a Vehicle Body - -
V113147

Remove in this Direction - -


NOTICE:

Make sure that the cowl top ventilator louver sub-assembly does not contact the vehicle body, otherwise it may be damaged.



k.

Remove the cowl top ventilator louver sub-assembly as shown in the illustration.

E374986C01
0,0 0,0 false
V113147

Remove in this Direction - -



Hide 7.REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

a.
E364787

Disengage the 2 clamps.


b.

Disconnect the connector.


c.
E364788C01
2.375,2.896 2.344,2.708 true 2.302,2.896 2.479,3.063 0.177,0.167 10 true *a
*a Motor Grommet
V100135

Bolt (A)
V100136

Bolt (B)


Remove the bolt (A).


d.

Remove the bolt (B).

HINT:

Remove the bolt (B) and windshield wiper motor and link assembly as a set.



e.

Disengage the motor grommet as shown in the illustration and remove the windshield wiper motor and link assembly.

NOTICE:

Be careful not to damage the windshield glass when removing the windshield wiper motor and link assembly.



Hide 85110 8.REMOVE WINDSHIELD WIPER MOTOR ASSEMBLY

a.
E364789C01
2.615,1.521 2.094,1 true 2.292,0.896 2.583,0.583 true 1.396,0.677 1.667,0.417 true 2.625,1.542 2.938,1.698 0.313,0.156 10 false *a 2.563,0.406 2.875,0.563 0.313,0.156 10 false *b 1.646,0.26 1.958,0.417 0.313,0.156 10 false *1
*1 No. 1 Wiper Link Rod
*a Protective Tape
*b Pivot of Windshield Wiper Motor Assembly


Using a screwdriver, separate the No. 1 wiper link rod from the pivot of the windshield wiper motor assembly as shown in the illustration.

HINT:

Tape the screwdriver tip before use.



b.
E364790

Using a T30 "TORX" socket wrench, remove the 2 bolts and windshield wiper motor assembly from the wiper link assembly.