When the seat heater switch of the refreshing seat switch is operated, the air conditioning amplifier assembly receives a signal and operates the front seat heater.
If the auxiliary battery voltage is low, the seat heater system may not operate due to operation of auxiliary battery load control, check the Data List item "Battery Control Count (Body ECU)".
Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>DATA LIST / ACTIVE TEST
Inspect the fuses for circuits related to this system before performing the following procedure.
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Check for DTCs.
DTC B14B5 or B14C0 is not output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Air Conditioner / Active Test.
Perform the Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Front Right Seat Heater | Front seat RH side seat heater operation | OFF or ON | - |
| Tester Display |
|---|
| Front Right Seat Heater |
The seat heater operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the front seat cushion heater assembly RH.
for Manual Seat: Click hereVehicle Interior>SEAT>FRONT SEAT CUSHION HEATER(for Manual Seat)>REMOVAL
for Power Seat: Click hereVehicle Interior>SEAT>FRONT SEAT CUSHION HEATER(for Power Seat)>REMOVAL
Inspect the front seat cushion heater assembly RH.
for Manual Seat: Click hereVehicle Interior>SEAT>FRONT SEAT CUSHION HEATER(for Manual Seat)>INSPECTION
for Power Seat: Click hereVehicle Interior>SEAT>FRONT SEAT CUSHION HEATER(for Power Seat)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for Manual Seat: Click hereVehicle Interior>SEAT>FRONT SEAT CUSHION HEATER(for Manual Seat)>REMOVAL
for Power Seat: Click hereVehicle Interior>SEAT>FRONT SEAT CUSHION HEATER(for Power Seat)>REMOVAL
Remove the front seatback heater assembly RH.
for Manual Seat: Click hereVehicle Interior>SEAT>FRONT SEATBACK HEATER(for Manual Seat)>REMOVAL
for Power Seat: Click hereVehicle Interior>SEAT>FRONT SEATBACK HEATER(for Power Seat)>REMOVAL
Inspect the front seatback heater assembly RH.
for Manual Seat: Click hereVehicle Interior>SEAT>FRONT SEATBACK HEATER(for Manual Seat)>INSPECTION
for Power Seat: Click hereVehicle Interior>SEAT>FRONT SEATBACK HEATER(for Power Seat)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for Manual Seat: Click hereVehicle Interior>SEAT>FRONT SEATBACK HEATER(for Manual Seat)>REMOVAL
for Power Seat: Click hereVehicle Interior>SEAT>FRONT SEATBACK HEATER(for Power Seat)>REMOVAL
| *a | Front view of wire harness connector
(to Seat Heater Control Sub-assembly RH) |
Disconnect the a21 seat heater control sub-assembly RH connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| a21-1 (+B1) - Body ground | Power switch on (IG) | 11 to 14 V |
| a21-1 (+B1) - Body ground | Power switch off | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the a21 seat heater control sub-assembly RH connector.
Disconnect the K56 air conditioning amplifier assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K56-16 (SHP+) - a21-5 (SWR) | Always | Below 1 Ω |
| K56-16 (SHP+) or a21-5 (SWR) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the a11 front seat cushion heater assembly RH connector.
Disconnect the a21 seat heater control sub-assembly RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| a21-10 (E) - a11-6 | Always | Below 1 Ω |
| a21-10 (E) or a11-6 - Body ground | Always | 10 kΩ or higher |
| a21-7 (HTR1) - a11-1 | Always | Below 1 Ω |
| a21-7 (HTR1) or a11-1 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the a11 front seat cushion heater assembly RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| a11-2 - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Temporarily replace the seat heater control sub-assembly RH with a new or known good one.
| Proceed to |
|---|
| NEXT |
NEXT
Check the operation of the front seat heater.
Click hereVehicle Interior>SEAT>SEAT HEATER SYSTEM>OPERATION CHECK
The seat heater operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG