Home › Audio / Visual / Telematics › AUDIO / VIDEO › NOISE FILTER › 2017.09–2019.02
RM33C0E _56 Audio / Visual / Telematics _065450 AUDIO / VIDEO _0333635 NOISE FILTER A

AUDIO / VIDEO  NOISE FILTER  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during radio setting condenser removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedures Effect/Inoperative Function When Necessary Procedures are not Performed Link
Disconnect cable from negative auxiliary battery terminal Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control) (Click here)
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)

CAUTION:
B401522

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION


PROCEDURE

Hide 1. PRECAUTION (w/ Rear Seat Side Airbag)

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 64718C 2.REMOVE LUGGAGE TRIM SERVICE HOLE COVER (w/ Rear Seat Side Airbag)

Hide 3.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL (w/ Rear Seat Side Airbag)

Click hereGeneral>MAINTENANCE>AUXILIARY BATTERY>REMOVAL

CAUTION:
B422343

·

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

·

If an airbag deploys for any reason, it may cause a serious injury.



Hide 73350C 4.DISCONNECT REAR CENTER SEAT OUTER BELT ASSEMBLY (for Fold Down Seat Type)

Hide 5.REMOVE REAR SEAT CUSHION ASSEMBLY (for Fold Down Seat Type)

Hide 72693 6.REMOVE REAR SEAT CUSHION LOCK HOOK (for Fold Down Seat Type)

Hide 62332A 7.DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP LH (for Fold Down Seat Type)

Hide 8.REMOVE REAR SIDE SEATBACK ASSEMBLY LH (for Fold Down Seat Type)

Hide 71940A 9.REMOVE REAR SEAT HEADREST ASSEMBLY (for Reclining Seat Type)

Hide 73350C 10.DISCONNECT REAR CENTER SEAT OUTER BELT ASSEMBLY (for Reclining Seat Type)

Hide 11.REMOVE REAR SEAT CUSHION ASSEMBLY (for Reclining Seat Type)

Hide 72693 12.REMOVE REAR SEAT CUSHION LOCK HOOK (for Reclining Seat Type)

Hide 72996A 13.REMOVE REAR SEATBACK COVER (for Reclining Seat Type)

Hide 14.REMOVE REAR SEATBACK ASSEMBLY LH (for Reclining Seat Type)

Hide 62332A 15.DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP LH (for Reclining Seat Type)

Hide 16.REMOVE REAR SIDE SEATBACK ASSEMBLY LH (for Reclining Seat Type)

Hide 62472A 17.REMOVE INNER ROOF SIDE GARNISH LH

Hide 86011V 18.REMOVE RADIO SETTING CONDENSER (for High Mounted Stop Light)

NOTICE:

When a terminal cover is removed, the radio setting condenser must be replaced because the terminal covers and condenser are supplied as a set.


a.
E357116

Remove the bolt.


b.

Disengage the clamp and disconnect the radio setting condenser with wire harness from the vehicle body.


c.
E365954C04
0,0 0,0 false
V113147

Remove in this Direction


Disengage the claw and pull out the cover as shown in the illustration.


d.
E368797C01
0,0 0,0 false
V113147

Remove in this Direction


Using a screwdriver, disengage the 6 claws and remove the 2 terminal covers with wire harness from the condenser as shown in the illustration.


e.
E223708

Using a screwdriver, bend back and break off the claw as shown in the illustration.

HINT:

Use the same procedure for the other terminal cover.



f.

Remove the 2 terminal covers from the wire harness.

NOTICE:
·

Make sure to hold the crimping side of the terminal when disconnecting the wire harness from the terminal cover.

·

Make sure not to bend the exposed wire when disconnecting the wire harness from the terminal cover.

·

Check for deformation of the terminal after the wire harness has been removed from the terminal cover.




Hide 86011R 19.REMOVE RADIO SETTING CONDENSER (for Window Defogger)

NOTICE:

When the terminal cover is removed, the radio setting condenser must be replaced because the terminal cover and condenser are supplied as a set.


a.
E357115

Remove the bolt.


b.

Disengage the clamp and disconnect the radio setting condenser with wire harness from the vehicle body.


c.
E365957C03
0,0 0,0 false
V113147

Remove in this Direction


Using a screwdriver, disengage the 3 claws and remove the terminal cover with wire harness from the condenser as shown in the illustration.


d.
E227453

Using a screwdriver, bend back and break off the claw as shown in the illustration.


e.

Remove the terminal cover from the wire harness.

NOTICE:
·

Make sure to hold the crimping side of the terminal when disconnecting the wire harness from the terminal cover.

·

Make sure not to bend the exposed wire when disconnecting the wire harness from the terminal cover.

·

Check for deformation of the terminal after the wire harness has been removed from the terminal cover.