Home › Audio / Visual / Telematics › AUDIO / VIDEO › NOISE FILTER
RM33C0E _56 Audio / Visual / Telematics _065450 AUDIO / VIDEO _0333635 NOISE FILTER G

AUDIO / VIDEO  NOISE FILTER  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 86011V 1.INSPECT RADIO SETTING CONDENSER (for High Mounted Stop Light)

a.

With the radio setting condenser installed, check that there is no looseness or other abnormalities.


b.
E386542C01
1.594,0.417 2.073,0.333 false 2.125,0.26 2.281,0.458 0.156,0.198 10 false 1 0.073,0.063 0.385,0.219 0.313,0.156 10 false *a
*a Radio Setting Condenser


Measure the resistance of the radio setting condenser according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - Body ground
·

Power switch off

·

High mounted stop light off

·

Luggage compartment room light off


Below 1 Ω



c.

Remove the bolt.


d.

Disengage the clamp and disconnect the radio setting condenser with wire harness from the vehicle body.


e.
E211797C03
2.406,1.729 1.927,1.729 false 1.917,0.917 2.448,1.177 false 1.927,0.76 2.406,0.542 false 2.479,1.115 2.573,1.26 0.094,0.146 10 2 2.406,1.646 2.5,1.802 0.094,0.156 10 3 2.427,0.438 2.521,0.583 0.094,0.146 10 1 0.063,0.042 0.375,0.198 0.313,0.156 10 *a
*a Radio Setting Condenser


Measure the resistance and voltage of the radio setting condenser according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2
·

Power switch off

·

High mounted stop light off

·

Luggage compartment room light off


10 kΩ or higher
1 - 3 10 kΩ or higher


Standard Voltage:
Tester Connection Condition Specified Condition
2 - Body ground
·

Power switch on (IG)

·

High mounted stop light off


Below 1 V
3 - Body ground
·

Power switch on (IG)

·

Luggage compartment room light off


Below 1 V
2 - Body ground
·

Power switch on (IG)

·

High mounted stop light on


11 to 14 V
3 - Body ground
·

Power switch on (IG)

·

Luggage compartment room light on


11 to 14 V



Hide 86011R 2.INSPECT RADIO SETTING CONDENSER (for Window Defogger)

a.

With the radio setting condenser installed, check that there is no looseness or other abnormalities.


b.
E386541C12
1.01,0.479 1.594,0.479 false 0.906,0.406 1.063,0.604 0.156,0.198 10 false 1 0.146,0.146 0.458,0.344 0.313,0.198 10 false *a
*a Radio Setting Condenser


Measure the resistance of the radio setting condenser according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - Body ground
·

Power switch off

·

Window Defogger turned off


Below 1 Ω



c.

Remove the bolt.


d.

Disengage the 2 clamps and disconnect the radio setting condenser with wire harness from the vehicle body.


e.
E230106C36
2.083,1.583 2.542,1.427 false 1.344,1.594 0.813,1.427 false 2.563,1.333 2.677,1.49 0.115,0.156 11 false 3 0.708,1.313 0.823,1.469 0.115,0.156 10 false 2 0.063,0.073 0.271,0.229 0.208,0.156 10 false *a
*a Radio Setting Condenser


Measure the resistance and voltage of the radio setting condenser according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 - 3
·

Power switch off

·

Window Defogger turned off


10 kΩ or higher


Standard Voltage:
Tester Connection Condition Specified Condition
2 - Body ground
·

Power switch on (IG)

·

Window Defogger turned off


Below 1 V
2 - Body ground
·

Power switch on (IG)

·

Window Defogger turned on


11 to 14 V