Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM
RM33C0E _59 Vehicle Exterior _065467 WINDOW / GLASS _0333691 POWER WINDOW CONTROL SYSTEM U

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM  TERMINALS OF ECU  


CHECK MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY


B150964C14
2.844,0.135 3.25,0.375 0.406,0.24 3.917,0.135 4.323,0.375 0.406,0.24 2.969,0.167 3.26,0.365 0.292,0.198 10 false O2 4.031,0.167 4.323,0.365 0.292,0.198 10 false N2 3.313,0.177 3.604,0.375 0.292,0.198 10 false *A 4.396,0.156 4.688,0.354 0.292,0.198 10 false *B
*A for LHD *B for RHD


a.

Disconnect the O2*1 or N2*2 multiplex network master switch assembly connector.

*1: for LHD

*2: for RHD



b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


for LHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
O2-11 (B) - O2-12 (GND) LA-R - W-B Power supply Power switch off 11 to 14 V
O2-12 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω

for RHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
N2-11 (B) - N2-12 (GND) LA-R - W-B Power supply Power switch off 11 to 14 V
N2-12 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω


c.

Reconnect the O2*1 or N2*2 multiplex network master switch assembly connector.

*1: for LHD

*2: for RHD



d.

Measure the voltage according to the value(s) in the table below.

for LHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
O2-15 (DOWN) - O2-12 (GND) LA-V - W-B Power window motor DOWN output Power switch on (IG), driver door power window regulator switch not pushed or not pulled 11 to 14 V
O2-15 (DOWN) - O2-12 (GND) LA-V - W-B Power window motor DOWN output Power switch on (IG), driver door power window moving, driver door power window regulator switch pushed halfway down (Manual operation) Below 1 V
O2-20 (UP) - O2-12 (GND) LA-L - W-B Power window motor UP output Power switch on (IG), driver door power window regulator switch not pushed or not pulled 11 to 14 V
O2-20 (UP) - O2-12 (GND) LA-L - W-B Power window motor UP output Power switch on (IG), driver door power window moving, driver door power window regulator switch pulled halfway up (Manual operation) Below 1 V

for RHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
N2-15 (DOWN) - N2-12 (GND) LA-V - W-B Power window motor DOWN output Power switch on (IG), driver door power window regulator switch not pushed or not pulled 11 to 14 V
N2-15 (DOWN) - N2-12 (GND) LA-V - W-B Power window motor DOWN output Power switch on (IG), driver door power window moving, driver door power window regulator switch pushed halfway down (Manual operation) Below 1 V
N2-20 (UP) - N2-12 (GND) LA-L - W-B Power window motor UP output Power switch on (IG), driver door power window regulator switch not pushed or not pulled 11 to 14 V
N2-20 (UP) - N2-12 (GND) LA-L - W-B Power window motor UP output Power switch on (IG), driver door power window moving, driver door power window regulator switch pulled halfway up (Manual operation) Below 1 V



CHECK POWER WINDOW REGULATOR SWITCH ASSEMBLY


B429631C04
2.854,0.208 3.271,0.479 0.417,0.271 4.052,0.198 4.469,0.469 0.417,0.271 2.979,0.271 3.292,0.469 0.313,0.198 10 false N3 4.167,0.24 4.479,0.438 0.313,0.198 10 false O3 3.333,0.25 3.646,0.448 0.313,0.198 10 false *A 4.531,0.24 4.844,0.438 0.313,0.198 10 false *B
*A for LHD *B for RHD


a.

Disconnect the N3*1 or O3*2 power window regulator switch assembly connector.

*1: for LHD

*2: for RHD



b.

Measure the resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


for LHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
N3-7 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω

for RHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
O3-7 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω


c.

Reconnect the N3*1 or O3*2 power window regulator switch assembly connector.

*1: for LHD

*2: for RHD



d.

Measure the voltage according to the value(s) in the table below.

for LHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
N3-2 (LED) - N3-7 (GND) GR - W-B LED illumination signal Headlight dimmer switch is in the tail position 11 to 14 V
N3-2 (LED) - N3-7 (GND) GR - W-B LED illumination signal Headlight dimmer switch is not in the tail position Below 1 V
N3-5 (UP) - N3-7 (GND) LA-W - W-B Power window motor UP output Power switch on (IG), power window regulator switch assembly not pushed or not pulled 11 to 14 V
N3-5 (UP) - N3-7 (GND) LA-W - W-B Power window motor UP output Power switch on (IG), front passenger door power window moving, power window regulator switch assembly pulled halfway up (Manual operation) Below 1 V
N3-5 (UP) - N3-7 (GND) LA-W - W-B Power window motor UP output Power switch on (IG), front passenger door power window fully open 11 to 14 V
N3-5 (UP) - N3-7 (GND) LA-W - W-B Power window motor UP output Power switch on (IG), front passenger door power window moving, power window regulator switch assembly fully pulled up (Auto operation) Below 1 V
N3-5 (UP) - N3-7 (GND) LA-W - W-B Power window motor UP output Power switch on (IG), front passenger door power window fully closed 11 to 14 V
N3-4 (DOWN) - N3-7 (GND) LA-R - W-B Power window motor DOWN output Power switch on (IG), power window regulator switch assembly not pushed or not pulled 11 to 14 V
N3-4 (DOWN) - N3-7 (GND) LA-R - W-B Power window motor DOWN output Power switch on (IG), front passenger door power window moving, power window regulator switch assembly pushed halfway down (Manual operation) Below 1 V
N3-4 (DOWN) - N3-7 (GND) LA-R - W-B Power window motor DOWN output Power switch on (IG), front passenger door power window fully closed 11 to 14 V
N3-4 (DOWN) - N3-7 (GND) LA-R - W-B Power window motor DOWN output Power switch on (IG), front passenger door power window moving, power window regulator switch assembly fully pushed down (Auto operation) Below 1 V
N3-4 (DOWN) - N3-7 (GND) LA-R - W-B Power window motor DOWN output Power switch on (IG), front passenger door power window fully open 11 to 14 V
N3-8 (AUTO) - N3-7 (GND) LA-G - W-B Power window motor AUTO UP output Power switch on (IG), front passenger door power window fully open 11 to 14 V
N3-8 (AUTO) - N3-7 (GND) LA-G - W-B Power window motor AUTO UP output Power switch on (IG), front passenger door power window moving, power window regulator switch assembly fully pulled up (Auto operation) Below 1 V
N3-8 (AUTO) - N3-7 (GND) LA-G - W-B Power window motor AUTO UP output Power switch on (IG), front passenger door power window fully closed 11 to 14 V
N3-8 (AUTO) - N3-7 (GND) LA-G - W-B Power window motor AUTO DOWN output Power switch on (IG), front passenger door power window fully closed 11 to 14 V
N3-8 (AUTO) - N3-7 (GND) LA-G - W-B Power window motor AUTO DOWN output Power switch on (IG), front passenger door power window moving, power window regulator switch assembly fully pushed down (Auto operation) Below 1 V
N3-8 (AUTO) - N3-7 (GND) LA-G - W-B Power window motor AUTO DOWN output Power switch on (IG), front passenger door power window fully open 11 to 14 V

for RHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
O3-2 (LED) - O3-7 (GND) GR - W-B LED illumination signal Headlight dimmer switch is in the tail position 11 to 14 V
O3-2 (LED) - O3-7 (GND) GR - W-B LED illumination signal Headlight dimmer switch is not in the tail position Below 1 V
O3-5 (UP) - O3-7 (GND) LA-W - W-B Power window motor UP output Power switch on (IG), power window regulator switch assembly not pushed or not pulled 11 to 14 V
O3-5 (UP) - O3-7 (GND) LA-W - W-B Power window motor UP output Power switch on (IG), front passenger door power window moving, power window regulator switch assembly pulled halfway up (Manual operation) Below 1 V
O3-5 (UP) - O3-7 (GND) LA-W - W-B Power window motor UP output Power switch on (IG), front passenger door power window fully open 11 to 14 V
O3-5 (UP) - O3-7 (GND) LA-W - W-B Power window motor UP output Power switch on (IG), front passenger door power window moving, power window regulator switch assembly fully pulled up (Auto operation) Below 1 V
O3-5 (UP) - O3-7 (GND) LA-W - W-B Power window motor UP output Power switch on (IG), front passenger door power window fully closed 11 to 14 V
O3-4 (DOWN) - O3-7 (GND) LA-R - W-B Power window motor DOWN output Power switch on (IG), power window regulator switch assembly not pushed or not pulled 11 to 14 V
O3-4 (DOWN) - O3-7 (GND) LA-R - W-B Power window motor DOWN output Power switch on (IG), front passenger door power window moving, power window regulator switch assembly pushed halfway down (Manual operation) Below 1 V
O3-4 (DOWN) - O3-7 (GND) LA-R - W-B Power window motor DOWN output Power switch on (IG), front passenger door power window fully closed 11 to 14 V
O3-4 (DOWN) - O3-7 (GND) LA-R - W-B Power window motor DOWN output Power switch on (IG), front passenger door power window moving, power window regulator switch assembly fully pushed down (Auto operation) Below 1 V
O3-4 (DOWN) - O3-7 (GND) LA-R - W-B Power window motor DOWN output Power switch on (IG), front passenger door power window fully open 11 to 14 V
O3-8 (AUTO) - O3-7 (GND) LA-G - W-B Power window motor AUTO UP output Power switch on (IG), front passenger door power window fully open 11 to 14 V
O3-8 (AUTO) - O3-7 (GND) LA-G - W-B Power window motor AUTO UP output Power switch on (IG), front passenger door power window moving, power window regulator switch assembly fully pulled up (Auto operation) Below 1 V
O3-8 (AUTO) - O3-7 (GND) LA-G - W-B Power window motor AUTO UP output Power switch on (IG), front passenger door power window fully closed 11 to 14 V
O3-8 (AUTO) - O3-7 (GND) LA-G - W-B Power window motor AUTO DOWN output Power switch on (IG), front passenger door power window fully closed 11 to 14 V
O3-8 (AUTO) - O3-7 (GND) LA-G - W-B Power window motor AUTO DOWN output Power switch on (IG), front passenger door power window moving, power window regulator switch assembly fully pushed down (Auto operation) Below 1 V
O3-8 (AUTO) - O3-7 (GND) LA-G - W-B Power window motor AUTO DOWN output Power switch on (IG), front passenger door power window fully open 11 to 14 V



CHECK REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (for LH Door)


B429631N22
3.458,0.208 3.875,0.479 0.417,0.271 3.563,0.26 3.875,0.458 0.313,0.198 10 false Q2

a.

Disconnect the Q2 rear power window regulator switch assembly (for LH door) connector.


b.

Measure the resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
Q2-7 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω


c.

Reconnect the Q2 rear power window regulator switch assembly (for LH door) connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
Q2-2 (LED) - Q2-7 (GND) LG - W-B LED illumination signal Headlight dimmer switch is in the tail position 11 to 14 V
Q2-2 (LED) - Q2-7 (GND) LG - W-B LED illumination signal Headlight dimmer switch is not in the tail position Below 1 V
Q2-5 (UP) - Q2-7 (GND) LA-B - W-B Power window motor UP output Power switch on (IG), rear power window regulator switch assembly (for LH door) not pushed or not pulled 11 to 14 V
Q2-5 (UP) - Q2-7 (GND) LA-B - W-B Power window motor UP output Power switch on (IG), rear LH door power window moving, rear power window regulator switch assembly (for LH door) pulled halfway up (Manual operation) Below 1 V
Q2-5 (UP) - Q2-7 (GND) LA-B - W-B Power window motor UP output Power switch on (IG), rear LH door power window fully open 11 to 14 V
Q2-5 (UP) - Q2-7 (GND) LA-B - W-B Power window motor UP output Power switch on (IG), rear LH door power window moving, rear power window regulator switch assembly (for LH door) fully pulled up (Auto operation) Below 1 V
Q2-5 (UP) - Q2-7 (GND) LA-B - W-B Power window motor UP output Power switch on (IG), rear LH door power window fully closed 11 to 14 V
Q2-4 (DOWN) - Q2-7 (GND) LA-R - W-B Power window motor DOWN output Power switch on (IG), rear power window regulator switch assembly (for LH door) not pushed or not pulled 11 to 14 V
Q2-4 (DOWN) - Q2-7 (GND) LA-R - W-B Power window motor DOWN output Power switch on (IG), rear LH door power window moving, rear power window regulator switch assembly (for LH door) pushed halfway down (Manual operation) Below 1 V
Q2-4 (DOWN) - Q2-7 (GND) LA-R - W-B Power window motor DOWN output Power switch on (IG), rear LH door power window fully closed 11 to 14 V
Q2-4 (DOWN) - Q2-7 (GND) LA-R - W-B Power window motor DOWN output Power switch on (IG), rear LH door power window moving, rear power window regulator switch assembly (for LH door) fully pushed down (Auto operation) Below 1 V
Q2-4 (DOWN) - Q2-7 (GND) LA-R - W-B Power window motor DOWN output Power switch on (IG), rear LH door power window fully open 11 to 14 V
Q2-8 (AUTO) - Q2-7 (GND) LA-GR - W-B Power window motor AUTO UP output Power switch on (IG), rear LH door power window fully open 11 to 14 V
Q2-8 (AUTO) - Q2-7 (GND) LA-GR - W-B Power window motor AUTO UP output Power switch on (IG), rear LH door power window moving, rear power window regulator switch assembly (for LH door) fully pulled up (Auto operation) Below 1 V
Q2-8 (AUTO) - Q2-7 (GND) LA-GR - W-B Power window motor AUTO UP output Power switch on (IG), rear LH door power window fully closed 11 to 14 V
Q2-8 (AUTO) - Q2-7 (GND) LA-GR - W-B Power window motor AUTO DOWN output Power switch on (IG), rear LH door power window fully closed 11 to 14 V
Q2-8 (AUTO) - Q2-7 (GND) LA-GR - W-B Power window motor AUTO DOWN output Power switch on (IG), rear LH door power window moving, rear power window regulator switch assembly (for LH door) fully pushed down (Auto operation) Below 1 V
Q2-8 (AUTO) - Q2-7 (GND) LA-GR - W-B Power window motor AUTO DOWN output Power switch on (IG), rear LH door power window fully open 11 to 14 V



CHECK REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (for RH Door)


B429631N23
3.458,0.208 3.875,0.479 0.417,0.271 3.573,0.26 3.885,0.458 0.313,0.198 10 false P2

a.

Disconnect the P2 rear power window regulator switch assembly (for RH door) connector.


b.

Measure the resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
P2-7 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω


c.

Reconnect the P2 rear power window regulator switch assembly (for RH door) connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
P2-2 (LED) - P2-7 (GND) LG - W-B LED illumination signal Headlight dimmer switch is in the tail position 11 to 14 V
P2-2 (LED) - P2-7 (GND) LG - W-B LED illumination signal Headlight dimmer switch is not in the tail position Below 1 V
P2-5 (UP) - P2-7 (GND) LA-B - W-B Power window motor UP output Power switch on (IG), rear power window regulator switch assembly (for RH door) not pushed or not pulled 11 to 14 V
P2-5 (UP) - P2-7 (GND) LA-B - W-B Power window motor UP output Power switch on (IG), rear RH door power window moving, rear power window regulator switch assembly (for RH door) pulled halfway up (Manual operation) Below 1 V
P2-5 (UP) - P2-7 (GND) LA-B - W-B Power window motor UP output Power switch on (IG), rear RH door power window fully open 11 to 14 V
P2-5 (UP) - P2-7 (GND) LA-B - W-B Power window motor UP output Power switch on (IG), rear RH door power window moving, rear power window regulator switch assembly (for RH door) fully pulled up (Auto operation) Below 1 V
P2-5 (UP) - P2-7 (GND) LA-B - W-B Power window motor UP output Power switch on (IG), rear RH door power window fully closed 11 to 14 V
P2-4 (DOWN) - P2-7 (GND) LA-R - W-B Power window motor DOWN output Power switch on (IG), rear power window regulator switch assembly (for RH door) not pushed or not pulled 11 to 14 V
P2-4 (DOWN) - P2-7 (GND) LA-R - W-B Power window motor DOWN output Power switch on (IG), rear RH door power window moving, rear power window regulator switch assembly (for RH door) pushed halfway down (Manual operation) Below 1 V
P2-4 (DOWN) - P2-7 (GND) LA-R - W-B Power window motor DOWN output Power switch on (IG), rear RH door power window fully closed 11 to 14 V
P2-4 (DOWN) - P2-7 (GND) LA-R - W-B Power window motor DOWN output Power switch on (IG), rear RH door power window moving, rear power window regulator switch assembly (for RH door) fully pushed down (Auto operation) Below 1 V
P2-4 (DOWN) - P2-7 (GND) LA-R - W-B Power window motor DOWN output Power switch on (IG), rear RH door power window fully open 11 to 14 V
P2-8 (AUTO) - P2-7 (GND) LA-GR - W-B Power window motor AUTO UP output Power switch on (IG), rear RH door power window fully open 11 to 14 V
P2-8 (AUTO) - P2-7 (GND) LA-GR - W-B Power window motor AUTO UP output Power switch on (IG), rear RH door power window moving, rear power window regulator switch assembly (for RH door) fully pulled up (Auto operation) Below 1 V
P2-8 (AUTO) - P2-7 (GND) LA-GR - W-B Power window motor AUTO UP output Power switch on (IG), rear RH door power window fully closed 11 to 14 V
P2-8 (AUTO) - P2-7 (GND) LA-GR - W-B Power window motor AUTO DOWN output Power switch on (IG), rear RH door power window fully closed 11 to 14 V
P2-8 (AUTO) - P2-7 (GND) LA-GR - W-B Power window motor AUTO DOWN output Power switch on (IG), rear RH door power window moving, rear power window regulator switch assembly (for RH door) fully pushed down (Auto operation) Below 1 V
P2-8 (AUTO) - P2-7 (GND) LA-GR - W-B Power window motor AUTO DOWN output Power switch on (IG), rear RH door power window fully open 11 to 14 V



CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Door)


B280976C31
2.021,0.51 2.417,0.75 0.396,0.24 2.031,1.021 2.427,1.26 0.396,0.24 2.125,0.552 2.448,0.771 0.323,0.219 10 false O6 2.156,1.073 2.479,1.292 0.323,0.219 10 false N7 2.479,0.542 2.802,0.76 0.323,0.219 10 false *A 2.479,1.073 2.802,1.292 0.323,0.219 10 false *B
*A for LHD *B for RHD


a.

Disconnect the O6*1 or N7*2 power window regulator motor assembly (for driver door) connector.

*1: for LHD

*2: for RHD



b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


for LHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
O6-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
O6-2 (B) - Body ground GR - Body ground Power supply Power switch off 11 to 14 V

for RHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
N7-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
N7-2 (B) - Body ground GR - Body ground Power supply Power switch off 11 to 14 V


c.

Reconnect the O6*1 or N7*2 power window regulator motor assembly (for driver door) connector.

*1: for LHD

*2: for RHD



d.

Measure the voltage according to the value(s) in the table below.

for LHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
O6-7 (DOWN) - O6-1 (GND) LA-V - W-B Power window motor DOWN input Power switch on (IG), multiplex network master switch assembly (driver door power window regulator switch) not pushed or not pulled 11 to 14 V
O6-7 (DOWN) - O6-1 (GND) LA-V - W-B Power window motor DOWN input Power switch on (IG), driver door power window moving, multiplex network master switch assembly (driver door power window regulator switch) pushed halfway down (Manual operation) Below 1 V
O6-7 (DOWN) - O6-1 (GND) LA-V - W-B Power window motor DOWN input Power switch on (IG), driver door power window fully closed 11 to 14 V
O6-7 (DOWN) - O6-1 (GND) LA-V - W-B Power window motor DOWN input Power switch on (IG), driver door power window moving, multiplex network master switch assembly (driver door power window regulator switch) fully pushed down (Auto operation) Below 1 V
O6-7 (DOWN) - O6-1 (GND) LA-V - W-B Power window motor DOWN input Power switch on (IG), driver door power window fully open 11 to 14 V
O6-10 (UP) - O6-1 (GND) LA-L - W-B Power window motor UP input Power switch on (IG), multiplex network master switch assembly (driver door power window regulator switch) not pushed or not pulled 11 to 14 V
O6-10 (UP) - O6-1 (GND) LA-L - W-B Power window motor UP input Power switch on (IG), driver door power window moving, multiplex network master switch assembly (driver door power window regulator switch) pulled halfway up (Manual operation) Below 1 V
O6-10 (UP) - O6-1 (GND) LA-L - W-B Power window motor UP input Power switch on (IG), multiplex network master switch assembly (driver door power window regulator switch) fully open 11 to 14 V
O6-10 (UP) - O6-1 (GND) LA-L - W-B Power window motor UP input Power switch on (IG), driver door power window moving, multiplex network master switch assembly (driver door power window regulator switch) fully pulled up (Auto operation) Below 1 V
O6-10 (UP) - O6-1 (GND) LA-L - W-B Power window motor UP input Power switch on (IG), driver door power window fully closed 11 to 14 V

for RHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
N7-7 (DOWN) - N7-1 (GND) LA-V - W-B Power window motor DOWN input Power switch on (IG), multiplex network master switch assembly (driver door power window regulator switch) not pushed or not pulled 11 to 14 V
N7-7 (DOWN) - N7-1 (GND) LA-V - W-B Power window motor DOWN input Power switch on (IG), driver door power window moving, multiplex network master switch assembly (driver door power window regulator switch) pushed halfway down (Manual operation) Below 1 V
N7-7 (DOWN) - N7-1 (GND) LA-V - W-B Power window motor DOWN input Power switch on (IG), driver door power window fully closed 11 to 14 V
N7-7 (DOWN) - N7-1 (GND) LA-V - W-B Power window motor DOWN input Power switch on (IG), driver door power window moving, multiplex network master switch assembly (driver door power window regulator switch) fully pushed down (Auto operation) Below 1 V
N7-7 (DOWN) - N7-1 (GND) LA-V - W-B Power window motor DOWN input Power switch on (IG), driver door power window fully open 11 to 14 V
N7-10 (UP) - N7-1 (GND) LA-L - W-B Power window motor UP input Power switch on (IG), multiplex network master switch assembly (driver door power window regulator switch) not pushed or not pulled 11 to 14 V
N7-10 (UP) - N7-1 (GND) LA-L - W-B Power window motor UP input Power switch on (IG), driver door power window moving, multiplex network master switch assembly (driver door power window regulator switch) pulled halfway up (Manual operation) Below 1 V
N7-10 (UP) - N7-1 (GND) LA-L - W-B Power window motor UP input Power switch on (IG), multiplex network master switch assembly (driver door power window regulator switch) fully open 11 to 14 V
N7-10 (UP) - N7-1 (GND) LA-L - W-B Power window motor UP input Power switch on (IG), driver door power window moving, multiplex network master switch assembly (driver door power window regulator switch) fully pulled up (Auto operation) Below 1 V
N7-10 (UP) - N7-1 (GND) LA-L - W-B Power window motor UP input Power switch on (IG), driver door power window fully closed 11 to 14 V



CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Front Passenger Door)


B280976C29
1.969,0.479 2.365,0.719 0.396,0.24 1.969,0.979 2.365,1.219 0.396,0.24 2.083,0.5 2.5,0.708 0.417,0.208 10 false N7 2.073,1.01 2.49,1.219 0.417,0.208 10 false O6 2.438,0.51 2.854,0.719 0.417,0.208 10 false *A 2.448,1 2.865,1.208 0.417,0.208 10 false *B
*A for LHD *B for RHD


a.

Disconnect the N7*1 or O6*2 power window regulator motor assembly (for front passenger door) connector.

*1: for LHD

*2: for RHD



b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


for LHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
N7-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
N7-2 (B) - Body ground GR - Body ground Power supply Power switch off 11 to 14 V

for RHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
O6-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
O6-2 (B) - Body ground GR - Body ground Power supply Power switch off 11 to 14 V


c.

Reconnect the N7*1 or O6*2 power window regulator motor assembly (for front passenger door) connector.

*1: for LHD

*2: for RHD



d.

Measure the voltage according to the value(s) in the table below.

for LHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
N7-4 (AUTO) - N7-1 (GND) LA-G - W-B Power window motor AUTO UP input Power switch on (IG), front passenger door power window fully open 11 to 14 V
N7-4 (AUTO) - N7-1 (GND) LA-G - W-B Power window motor AUTO UP input Power switch on (IG), front passenger door power window moving, power window regulator switch assembly fully pulled up (Auto operation) Below 1 V
N7-4 (AUTO) - N7-1 (GND) LA-G - W-B Power window motor AUTO UP input Power switch on (IG), front passenger door power window fully closed 11 to 14 V
N7-4 (AUTO) - N7-1 (GND) LA-G - W-B Power window motor AUTO DOWN input Power switch on (IG), front passenger door power window fully closed 11 to 14 V
N7-4 (AUTO) - N7-1 (GND) LA-G - W-B Power window motor AUTO DOWN input Power switch on (IG), front passenger door power window moving, power window regulator switch assembly fully pushed down (Auto operation) Below 1 V
N7-4 (AUTO) - N7-1 (GND) LA-G - W-B Power window motor AUTO DOWN input Power switch on (IG), front passenger door power window fully open 11 to 14 V
N7-5 (LED) - N7-1 (GND) GR - W-B LED illumination signal Headlight dimmer switch is in the tail position 11 to 14 V
N7-5 (LED) - N7-1 (GND) GR - W-B LED illumination signal Headlight dimmer switch is not in the tail position Below 1 V
N7-7 (DOWN) - N7-1 (GND) LA-R - W-B Power window motor DOWN input Power switch on (IG), power window regulator switch assembly not pushed or not pulled 11 to 14 V
N7-7 (DOWN) - N7-1 (GND) LA-R - W-B Power window motor DOWN input Power switch on (IG), front passenger door power window moving, power window regulator switch assembly pushed halfway down (Manual operation) Below 1 V
N7-7 (DOWN) - N7-1 (GND) LA-R - W-B Power window motor DOWN input Power switch on (IG), front passenger door power window fully closed 11 to 14 V
N7-7 (DOWN) - N7-1 (GND) LA-R - W-B Power window motor DOWN input Power switch on (IG), front passenger door power window moving, power window regulator switch assembly fully pushed down (Auto operation) Below 1 V
N7-7 (DOWN) - N7-1 (GND) LA-R - W-B Power window motor DOWN input Power switch on (IG), front passenger door power window fully open 11 to 14 V
N7-10 (UP) - N7-1 (GND) LA-W - W-B Power window motor UP input Power switch on (IG), power window regulator switch assembly not pushed or not pulled 11 to 14 V
N7-10 (UP) - N7-1 (GND) LA-W - W-B Power window motor UP input Power switch on (IG), front passenger door power window moving, power window regulator switch assembly pulled halfway up (Manual operation) Below 1 V
N7-10 (UP) - N7-1 (GND) LA-W - W-B Power window motor UP input Power switch on (IG), front passenger door power window fully open 11 to 14 V
N7-10 (UP) - N7-1 (GND) LA-W - W-B Power window motor UP input Power switch on (IG), front passenger door power window moving, power window regulator switch assembly fully pulled up (Auto operation) Below 1 V
N7-10 (UP) - N7-1 (GND) LA-W - W-B Power window motor UP input Power switch on (IG), front passenger door power window fully closed 11 to 14 V

for RHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
O6-4 (AUTO) - O6-1 (GND) LA-G - W-B Power window motor AUTO UP input Power switch on (IG), front passenger door power window fully open 11 to 14 V
O6-4 (AUTO) - O6-1 (GND) LA-G - W-B Power window motor AUTO UP input Power switch on (IG), front passenger door power window moving, power window regulator switch assembly fully pulled up (Auto operation) Below 1 V
O6-4 (AUTO) - O6-1 (GND) LA-G - W-B Power window motor AUTO UP input Power switch on (IG), front passenger door power window fully closed 11 to 14 V
O6-4 (AUTO) - O6-1 (GND) LA-G - W-B Power window motor AUTO DOWN input Power switch on (IG), front passenger door power window fully closed 11 to 14 V
O6-4 (AUTO) - O6-1 (GND) LA-G - W-B Power window motor AUTO DOWN input Power switch on (IG), front passenger door power window moving, power window regulator switch assembly fully pushed down (Auto operation) Below 1 V
O6-4 (AUTO) - O6-1 (GND) LA-G - W-B Power window motor AUTO DOWN input Power switch on (IG), front passenger door power window fully open 11 to 14 V
O6-5 (LED) - O6-1 (GND) GR - W-B LED illumination signal Headlight dimmer switch is in the tail position 11 to 14 V
O6-5 (LED) - O6-1 (GND) GR - W-B LED illumination signal Headlight dimmer switch is not in the tail position Below 1 V
O6-7 (DOWN) - O6-1 (GND) LA-R - W-B Power window motor DOWN input Power switch on (IG), power window regulator switch assembly not pushed or not pulled 11 to 14 V
O6-7 (DOWN) - O6-1 (GND) LA-R - W-B Power window motor DOWN input Power switch on (IG), front passenger door power window moving, power window regulator switch assembly pushed halfway down (Manual operation) Below 1 V
O6-7 (DOWN) - O6-1 (GND) LA-R - W-B Power window motor DOWN input Power switch on (IG), front passenger door power window fully closed 11 to 14 V
O6-7 (DOWN) - O6-1 (GND) LA-R - W-B Power window motor DOWN input Power switch on (IG), front passenger door power window moving, power window regulator switch assembly fully pushed down (Auto operation) Below 1 V
O6-7 (DOWN) - O6-1 (GND) LA-R - W-B Power window motor DOWN input Power switch on (IG), front passenger door power window fully open 11 to 14 V
O6-10 (UP) - O6-1 (GND) LA-W - W-B Power window motor UP input Power switch on (IG), power window regulator switch assembly not pushed or not pulled 11 to 14 V
O6-10 (UP) - O6-1 (GND) LA-W - W-B Power window motor UP input Power switch on (IG), front passenger door power window moving, power window regulator switch assembly pulled halfway up (Manual operation) Below 1 V
O6-10 (UP) - O6-1 (GND) LA-W - W-B Power window motor UP input Power switch on (IG), front passenger door power window fully open 11 to 14 V
O6-10 (UP) - O6-1 (GND) LA-W - W-B Power window motor UP input Power switch on (IG), front passenger door power window moving, power window regulator switch assembly fully pulled up (Auto operation) Below 1 V
O6-10 (UP) - O6-1 (GND) LA-W - W-B Power window motor UP input Power switch on (IG), front passenger door power window fully closed 11 to 14 V



CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear LH Door)


B286758N21
2.292,0.771 2.656,0.99 0.365,0.219 2.385,0.802 2.771,1.01 0.385,0.208 10 false Q6

a.

Disconnect the Q6 power window regulator motor assembly (for rear LH door) connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
Q6-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
Q6-2 (B) - Body ground B - Body ground Power supply Power switch off 11 to 14 V


c.

Reconnect the Q6 power window regulator motor assembly (for rear LH door) connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
Q6-4 (AUTO) - Q6-1 (GND) LA-GR - W-B Power window motor AUTO UP input Power switch on (IG), rear LH door power window fully open 11 to 14 V
Q6-4 (AUTO) - Q6-1 (GND) LA-GR - W-B Power window motor AUTO UP input Power switch on (IG), rear LH door power window moving, rear power window regulator switch assembly (for LH door) fully pulled up (Auto operation) Below 1 V
Q6-4 (AUTO) - Q6-1 (GND) LA-GR - W-B Power window motor AUTO UP input Power switch on (IG), rear LH door power window fully closed 11 to 14 V
Q6-4 (AUTO) - Q6-1 (GND) LA-GR - W-B Power window motor AUTO DOWN input Power switch on (IG), rear LH door power window fully closed 11 to 14 V
Q6-4 (AUTO) - Q6-1 (GND) LA-GR - W-B Power window motor AUTO DOWN input Power switch on (IG), rear LH door power window moving, rear power window regulator switch assembly (for LH door) fully pushed down (Auto operation) Below 1 V
Q6-4 (AUTO) - Q6-1 (GND) LA-GR - W-B Power window motor AUTO DOWN input Power switch on (IG), rear LH door power window fully open 11 to 14 V
Q6-5 (LED) - Q6-1 (GND) LG - W-B LED illumination signal Headlight dimmer switch is in the tail position 11 to 14 V
Q6-5 (LED) - Q6-1 (GND) LG - W-B LED illumination signal Headlight dimmer switch is not in the tail position Below 1 V
Q6-7 (DOWN) - Q6-1 (GND) LA-R - W-B Power window motor DOWN input Power switch on (IG), rear power window regulator switch assembly (for LH door) not pushed or not pulled 11 to 14 V
Q6-7 (DOWN) - Q6-1 (GND) LA-R - W-B Power window motor DOWN input Power switch on (IG), rear LH door power window moving, rear power window regulator switch assembly (for LH door) pushed halfway down (Manual operation) Below 1 V
Q6-7 (DOWN) - Q6-1 (GND) LA-R - W-B Power window motor DOWN input Power switch on (IG), rear LH door power window fully closed 11 to 14 V
Q6-7 (DOWN) - Q6-1 (GND) LA-R - W-B Power window motor DOWN input Power switch on (IG), rear LH door power window moving, rear power window regulator switch assembly (for LH door) fully pushed down (Auto operation) Below 1 V
Q6-7 (DOWN) - Q6-1 (GND) LA-R - W-B Power window motor DOWN input Power switch on (IG), rear LH door power window fully open 11 to 14 V
Q6-10 (UP) - Q6-1 (GND) LA-B - W-B Power window motor UP input Power switch on (IG), rear power window regulator switch assembly (for LH door) not pushed or not pulled 11 to 14 V
Q6-10 (UP) - Q6-1 (GND) LA-B - W-B Power window motor UP input Power switch on (IG), rear LH door power window moving, rear power window regulator switch assembly (for LH door) pulled halfway up (Manual operation) Below 1 V
Q6-10 (UP) - Q6-1 (GND) LA-B - W-B Power window motor UP input Power switch on (IG), rear LH door power window fully open 11 to 14 V
Q6-10 (UP) - Q6-1 (GND) LA-B - W-B Power window motor UP input Power switch on (IG), rear LH door power window moving, rear power window regulator switch assembly (for LH door) fully pulled up (Auto operation) Below 1 V
Q6-10 (UP) - Q6-1 (GND) LA-B - W-B Power window motor UP input Power switch on (IG), rear LH door power window fully closed 11 to 14 V



CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear RH Door)


B280976N70
2.219,0.771 2.615,1.01 0.396,0.24 2.333,0.813 2.646,1.052 0.313,0.24 10 false P6

a.

Disconnect the P6 power window regulator motor assembly (for rear RH door) connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
P6-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
P6-2 (B) - Body ground B - Body ground Power supply Power switch off 11 to 14 V


c.

Reconnect the P6 power window regulator motor assembly (for rear RH door) connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
P6-4 (AUTO) - P6-1 (GND) LA-GR - W-B Power window motor AUTO UP input Power switch on (IG), rear RH door power window fully open 11 to 14 V
P6-4 (AUTO) - P6-1 (GND) LA-GR - W-B Power window motor AUTO UP input Power switch on (IG), rear RH door power window moving, rear power window regulator switch assembly (for RH door) fully pulled up (Auto operation) Below 1 V
P6-4 (AUTO) - P6-1 (GND) LA-GR - W-B Power window motor AUTO UP input Power switch on (IG), rear RH door power window fully closed 11 to 14 V
P6-4 (AUTO) - P6-1 (GND) LA-GR - W-B Power window motor AUTO DOWN input Power switch on (IG), rear RH door power window fully closed 11 to 14 V
P6-4 (AUTO) - P6-1 (GND) LA-GR - W-B Power window motor AUTO DOWN input Power switch on (IG), rear RH door power window moving, rear power window regulator switch assembly (for RH door) fully pushed down (Auto operation) Below 1 V
P6-4 (AUTO) - P6-1 (GND) LA-GR - W-B Power window motor AUTO DOWN input Power switch on (IG), rear RH door power window fully open 11 to 14 V
P6-5 (LED) - P6-1 (GND) LG - W-B LED illumination signal Headlight dimmer switch is in the tail position 11 to 14 V
P6-5 (LED) - P6-1 (GND) LG - W-B LED illumination signal Headlight dimmer switch is not in the tail position Below 1 V
P6-7 (DOWN) - P6-1 (GND) LA-R - W-B Power window motor DOWN input Power switch on (IG), rear power window regulator switch assembly (for RH door) not pushed or not pulled 11 to 14 V
P6-7 (DOWN) - P6-1 (GND) LA-R - W-B Power window motor DOWN input Power switch on (IG), rear RH door power window moving, rear power window regulator switch assembly (for RH door) pushed halfway down (Manual operation) Below 1 V
P6-7 (DOWN) - P6-1 (GND) LA-R - W-B Power window motor DOWN input Power switch on (IG), rear RH door power window fully closed 11 to 14 V
P6-7 (DOWN) - P6-1 (GND) LA-R - W-B Power window motor DOWN input Power switch on (IG), rear RH door power window moving, rear power window regulator switch assembly (for RH door) fully pushed down (Auto operation) Below 1 V
P6-7 (DOWN) - P6-1 (GND) LA-R - W-B Power window motor DOWN input Power switch on (IG), rear RH door power window fully open 11 to 14 V
P6-10 (UP) - P6-1 (GND) LA-B - W-B Power window motor UP input Power switch on (IG), rear power window regulator switch assembly (for RH door) not pushed or not pulled 11 to 14 V
P6-10 (UP) - P6-1 (GND) LA-B - W-B Power window motor UP input Power switch on (IG), rear RH door power window moving, rear power window regulator switch assembly (for RH door) pulled halfway up (Manual operation) Below 1 V
P6-10 (UP) - P6-1 (GND) LA-B - W-B Power window motor UP input Power switch on (IG), rear RH door power window fully open 11 to 14 V
P6-10 (UP) - P6-1 (GND) LA-B - W-B Power window motor UP input Power switch on (IG), rear RH door power window moving, rear power window regulator switch assembly (for RH door) fully pulled up (Auto operation) Below 1 V
P6-10 (UP) - P6-1 (GND) LA-B - W-B Power window motor UP input Power switch on (IG), rear RH door power window fully closed 11 to 14 V



CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)


B472410C09
1.125,3.25 1.563,3.5 0.438,0.25 3.156,3.219 3.594,3.469 0.438,0.25 5.448,3.208 5.885,3.458 0.438,0.25 1.698,4.573 2.135,4.823 0.438,0.25 5.302,6.396 5.74,6.646 0.438,0.25 1.104,6.167 1.542,6.417 0.438,0.25 3.667,6.125 4.104,6.375 0.438,0.25 5.302,6.083 5.74,6.333 0.438,0.25 6.313,6.198 6.75,6.448 0.438,0.25 3.365,7.646 3.802,7.896 0.438,0.25 5.385,4.615 5.823,4.865 0.438,0.25 1.656,1.208 1.958,1.208 false 1.667,1.552 1.969,1.552 false 1.667,1.875 1.969,1.875 false 4.042,0.792 4.042,0.313 4.042,0.313 4.229,0.313 false 0.531,2.49 0.531,2.323 0.531,2.323 0.865,2.323 false 3.469,7.677 3.781,7.875 0.313,0.198 10 false MB 4.292,0.219 4.604,0.417 0.313,0.198 10 false MB 2.042,1.135 2.354,1.333 0.313,0.198 10 false K51 2.052,1.479 2.365,1.677 0.313,0.198 10 false K52 2.052,1.802 2.365,2 0.313,0.198 10 false K53 0.875,1.073 1.188,1.271 0.313,0.198 10 false 3D 0.875,1.656 1.188,1.854 0.313,0.198 10 false 3C 0.885,2.021 1.198,2.219 0.313,0.198 10 false 3E 5.854,1.146 6.167,1.344 0.313,0.198 10 false 3B 5.854,1.76 6.167,1.958 0.313,0.198 10 false 3A 1.229,3.281 1.542,3.479 0.313,0.198 10 false K53 3.271,3.25 3.583,3.448 0.313,0.198 10 false K52 5.542,3.24 5.854,3.438 0.313,0.198 10 false K51 1.833,4.604 2.146,4.802 0.313,0.198 10 false 3A 1.24,6.198 1.552,6.396 0.313,0.198 10 false 3C 3.813,6.156 4.125,6.354 0.313,0.198 10 false 3D 5.427,6.115 5.74,6.313 0.313,0.198 10 false 3F 6.448,6.229 6.76,6.427 0.313,0.198 10 false 3E 5.521,4.646 5.833,4.844 0.313,0.198 10 false 3B 5.427,6.427 5.74,6.625 0.313,0.198 10 false 3G 5.813,6.125 6.125,6.323 0.313,0.198 10 false *A 5.823,6.427 6.135,6.625 0.313,0.198 10 false *B 0.365,2.531 0.76,2.76 0.396,0.229 10 false 3F*A 0.365,2.698 0.865,2.885 0.5,0.188 10 false 3G*B
*A for LHD *B for RHD


a.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.


b.

Reconnect the instrument panel junction block assembly connectors.


c.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connectors connected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
MB-11 (GND1) - Body ground - Ground Always Below 1 Ω
MB-31 (BECU) - Body ground - Auxiliary battery power supply Power switch off 11 to 14 V
MB-30 (ACC) - Body ground - ACC power supply Power switch on (ACC) 11 to 14 V
MB-30 (ACC) - Body ground - ACC power supply Power switch off Below 1 V
MB-32 (IG) - Body ground - IG power supply Power switch on (IG) 11 to 14 V
MB-32 (IG) - Body ground - IG power supply Power switch off or on (ACC) Below 1 V


d.

Install the main body ECU (multiplex network body ECU) to the instrument panel junction block assembly.


e.

Measure the voltage and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
K52-1 (FLCY) - Body ground W - Body ground Front door courtesy light switch (for LH) input Front door LH open Below 1 V
K52-1 (FLCY) - Body ground W - Body ground Front door courtesy light switch (for LH) input Front door LH closed 11 to 14 V
K52-6 (FRCY) - Body ground BE - Body ground Front door courtesy light switch (for RH) input Front door RH open Below 1 V
K52-6 (FRCY) - Body ground BE - Body ground Front door courtesy light switch (for RH) input Front door RH closed 11 to 14 V
K53-18 (L2) - Body ground LG - Body ground Driver door key-linked lock input Driver door key cylinder turned to lock Below 1 V
K53-18 (L2) - Body ground LG - Body ground Driver door key-linked lock input Driver door key cylinder not turned Pulse generation
K53-17 (UL3) - Body ground BE - Body ground Driver door key-linked unlock input Driver door key cylinder turned to unlock Below 1 V
K53-17 (UL3) - Body ground BE - Body ground Driver door key-linked unlock input Driver door key cylinder not turned Pulse generation