Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW REGULATOR MOTOR (for Rear Door)
RM33C0E _59 Vehicle Exterior _065467 WINDOW / GLASS _0333695 POWER WINDOW REGULATOR MOTOR(for Rear Door) G

WINDOW / GLASS  POWER WINDOW REGULATOR MOTOR(for Rear Door)  INSPECTION  


PROCEDURE

Hide 1.INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR REAR LH DOOR)

a.
E292071C20
1.563,1.479 2.604,1.479 true 2.646,1.417 2.958,1.615 0.313,0.198 10 false *d 0.26,2.583 0.573,2.781 0.313,0.198 10 false *a 0.531,1.302 0.99,1.5 0.458,0.198 10 false *b 1.115,2.219 1.531,2.531 0.417,0.313 10 false *c
*a Component without harness connected
(Power Window Regulator Motor Assembly (for Rear LH Door))
*b Clockwise
*c Counterclockwise
*d Motor gear


Connect a positive (+) auxiliary battery lead to connector terminal 2.

NOTICE:

Do not connect a positive (+) auxiliary battery lead to any terminals other than terminal 2 to avoid damaging the pulse sensor inside the motor.



b.

Connect a negative (-) auxiliary battery lead to connector terminals 1 and 7 or 10.


c.

Check that the motor gear rotates smoothly as follows:

OK:
Measurement Condition Specified Condition
1.

Connect a positive (+) auxiliary battery lead to terminal 2, connect a negative (-) auxiliary battery lead to terminal 1, and keep them connected for 3 seconds or more.

2.

With terminals 2 and 1 connected, connect a negative (-) auxiliary battery lead to terminal 10.


Motor gear rotates clockwise
1.

Connect a positive (+) auxiliary battery lead to terminal 2, connect a negative (-) auxiliary battery lead to terminal 1, and keep them connected for 3 seconds or more.

2.

With terminals 2 and 1 connected, connect a negative (-) auxiliary battery lead to terminal 7.


Motor gear rotates counterclockwise


If the result is not as specified, replace the power window regulator motor assembly (for rear LH door).


CAUTION:

Initialize the power window control system after installing the power window regulator motor and regulator assembly.



Hide 2.INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR REAR RH DOOR)

a.
E292072C21
1.198,1.479 1.906,1.479 false 2.896,1.333 3.208,1.531 0.313,0.198 10 false *c 0.302,2.604 0.615,2.802 0.313,0.198 10 false *a 1,1.396 1.354,1.76 0.354,0.365 10 false *d 2.323,2.24 2.635,2.438 0.313,0.198 10 false *b
*a Component without harness connected
(Power Window Regulator Motor Assembly (for Rear RH Door))
*b Clockwise
*c Counterclockwise
*d Motor gear


Connect a positive (+) auxiliary battery lead to connector terminal 2.

NOTICE:

Do not connect a positive (+) auxiliary battery lead to any terminals other than terminal 2 to avoid damaging the pulse sensor inside the motor.



b.

Connect a negative (-) auxiliary battery lead to connector terminals 1 and 7 or 10.


c.

Check that the motor gear rotates smoothly as follows:

OK:
Measurement Condition Specified Condition
1.

Connect the positive (+) auxiliary battery lead to terminal 2, connect a negative (-) auxiliary battery lead to terminal 1, and keep them connected for 3 seconds or more.

2.

With terminals 2 and 1 connected, connect a negative (-) auxiliary battery lead to terminal 10.


Motor gear rotates counterclockwise
1.

Connect a positive (+) auxiliary battery lead to terminal 2, connect a negative (-) auxiliary battery lead to terminal 1, and keep them connected for 3 seconds or more.

2.

With terminals 2 and 1 connected, connect a negative (-) auxiliary battery lead to terminal 7.


Motor gear rotates clockwise


If the result is not as specified, replace the power window regulator motor assembly (for rear RH door).


CAUTION:

Initialize the power window control system after installing the power window regulator motor and regulator assembly.