Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › REAR DOOR WINDOW FRAME MOULDING
RM33C0E _59 Vehicle Exterior _065474 EXTERIOR PANELS / TRIM _0333724 REAR DOOR WINDOW FRAME MOULDING A

EXTERIOR PANELS / TRIM  REAR DOOR WINDOW FRAME MOULDING  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 75708 1.INSTALL REAR DOOR WINDOW FRAME MOULDING SUB-ASSEMBLY

a.

Engage the guide, 2 claws and clip to temporarily install the rear door window frame moulding sub-assembly to the door frame.

B469814


b.

Using an air riveter or hand riveter with a nose piece, install the rear door window frame moulding sub-assembly with 6 new rivets.

HINT:

If the mandrel of the rivet does not come off on the first operation of the rivet gun, slide the rivet gun forward on the mandrel and operate it again.


NOTICE:
·
B125583C09
1.292,0.281 1.438,0.281 1.438,0.281 1.781,0.74 false 1.875,1.271 1.875,1.823 false 1.125,0.208 1.438,0.365 0.313,0.156 10 false *a 1.823,1.875 2.135,2.094 0.313,0.219 10 false *b 2.063,0.063 2.385,0.302 0.323,0.24 10 false *c
*a Riveter
*b Mandrel
*c Incorrect


Do not pry the rivet with the riveter, as this will cause damage to the riveter and mandrel.

·
B125584C09
1.438,0.448 1.156,0.448 false 1.458,1.417 1.219,1.417 false 1.479,0.365 1.802,0.604 0.323,0.24 10 false *a 2.198,0.125 2.51,0.365 0.313,0.24 10 false *b 2.052,1.146 2.365,1.385 0.313,0.24 10 false *b 1.531,1.313 1.854,1.552 0.323,0.24 10 false *a
*a Riveter
*b Incorrect


Confirm that the rivets are seated properly against the moulding.

·

Do not tilt the riveter when installing the rivet to the moulding.

·

Do not leave any space between the rivet head and moulding.

·
B125585C10
1.135,0.771 1.396,0.771 false 1.438,0.667 1.75,0.938 0.313,0.271 10 false *a 2.01,0.188 2.344,0.469 0.333,0.281 10 false *b
*a Riveter
*b Incorrect


Do not leave any space between the moulding and door frame. Firmly hold the 2 items together while installing the rivet.




Hide 75762A 2.INSTALL REAR DOOR FRONT WINDOW FRAME MOULDING

HINT:

When installing a new rear door front window frame moulding, heat the vehicle body and rear door front window frame moulding using a heat light.


Heating Temperature
Item Temperature
Vehicle Body 40 to 60°C (104 to 140°F)
Rear Door Front Window Frame Moulding 20 to 30°C (68 to 86°F)

CAUTION:
E306500C23
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts, touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the vehicle body or rear door front window frame moulding excessively.


a.

Clean the vehicle body surface.

i.

Using a heat light, heat the vehicle body surface.


ii.

Remove any double-sided tape from the vehicle body.


iii.

Wipe off any tape adhesive residue with cleaner.



b.

Install a new rear door front window frame moulding.

i.

Using a heat light, heat the vehicle body and rear door front window frame moulding.


ii.

Remove the release paper from the rear door front window frame moulding.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.



iii.
B469812C01
0.469,2.031 0.938,2.083 true 1.396,2.24 1.885,2.156 true 0.427,2.448 1.292,2.531 true 1.906,2.042 2.219,2.24 0.313,0.198 10 false *a 0.229,2.344 0.542,2.542 0.313,0.198 10 false *b 0.271,1.927 0.583,2.125 0.313,0.198 10 false *a
*a Double-sided Tape
*b Caulking Sponge


Engage the clip and attach the double-sided tape and caulking sponge to install the rear door front window frame moulding.

HINT:

Press the rear door front window frame moulding firmly to install it.




Hide 67872 3.CONNECT REAR DOOR WEATHERSTRIP

a.

Engage the 2 clips and connect the rear door weatherstrip.


Hide 75740 4.INSTALL REAR DOOR BELT MOULDING ASSEMBLY