Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM
RM33C0E _56 Audio / Visual / Telematics _065451 NAVIGATION / MULTI INFO DISPLAY _0333738 NAVIGATION SYSTEM J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  Vehicle Speed Signal Circuit between Navigation ECU and Combination Meter  


DESCRIPTION

The navigation ECU receives a vehicle speed signal from the combination meter assembly.

HINT:
·

A voltage of 12 V or 5 V is output from each ECU and then input to the combination meter assembly. The signal is changed to a pulse signal at the transistor in the combination meter assembly. Each ECU controls its respective systems based on this pulse signal.

·

If a short occurs in any of the ECUs or in the wire harness connected to an ECU, all systems in the following diagram will not operate normally.



WIRING DIAGRAM

E369847E05
0.042,1.708 2.833,2.177 2.792,0.469 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly) 5.479,5.438 7.156,5.802 1.677,0.365 10 false Navigation ECU*1 0.115,3.896 2.552,4.25 2.438,0.354 10 false Radio and Display Receiver Assembly*3 0.094,5.438 2.833,5.781 2.74,0.344 10 false Stereo Component Amplifier Assembly*2 4.396,6.198 6.104,6.5 1.708,0.302 10 false *1: w/ Navigation System 0.083,6.958 3.031,7.302 2.948,0.344 10 false Parking Brake ECU (Brake Actuator Assembly) 4.156,3.927 7.156,4.313 3,0.385 10 false Certification ECU (Smart Key ECU Assembly) 5.135,2.26 7.01,2.583 1.875,0.323 10 false Combination Meter Assembly 5.563,0.719 6.146,1.021 0.583,0.302 10 false SI 5.552,1.25 6.135,1.552 0.583,0.302 10 false +S 1.438,0.729 2.021,1.031 0.583,0.302 10 false SP1 1.417,3.146 2,3.448 0.583,0.302 10 false SPD 6.031,0.354 6.615,0.656 0.583,0.302 10 false 12 V 1.448,4.688 2.031,4.99 0.583,0.302 10 false SPD 1.427,6.208 2.01,6.51 0.583,0.302 10 false SPD 5.531,4.677 6.115,4.979 0.583,0.302 10 false SPD 5.563,3.146 6.146,3.448 0.583,0.302 10 false SPD 4.396,6.708 6.219,6.979 1.823,0.271 10 false *2: for 9 Speakers 4.406,7.229 7.156,7.573 2.75,0.344 10 false *3: w/ No. 1 Stereo Jack Adapter Assembly 5.146,2.083 5.604,2.281 0.458,0.198 10 false K21 4.156,3.74 6.063,4.083 1.906,0.344 10 false K62 5.323,1.24 5.781,1.438 0.458,0.198 10 false 6 5.323,0.708 5.781,0.906 0.458,0.198 10 false 5 0.042,1.521 1.583,1.865 1.542,0.344 10 false A40 1.802,0.719 2.26,0.917 0.458,0.198 10 false 11 5.281,3.135 5.74,3.333 0.458,0.198 10 false 19 5.354,4.677 5.813,4.875 0.458,0.198 10 false 9 5.479,5.281 5.938,5.479 0.458,0.198 10 false K17 1.823,3.135 2.281,3.333 0.458,0.198 10 false 27 1.813,4.677 2.271,4.875 0.458,0.198 10 false 11 1.792,6.198 2.25,6.396 0.458,0.198 10 false 27 0.115,3.74 1.531,4.083 1.417,0.344 10 false K3 0.104,5.281 1.521,5.625 1.417,0.344 10 false K9 0.094,6.813 1.51,7.156 1.417,0.344 10 false A44

PROCEDURE

1.CHECK COMBINATION METER ASSEMBLY (OUTPUT WAVEFORM)
a.
E256135C82
1.5,0.417 1.917,0.667 0.417,0.25 2.406,1.917 2.188,1.333 true 0.167,0.198 0.479,0.396 0.313,0.198 10 false *a 1.573,0.458 1.885,0.656 0.313,0.198 10 false K21 2.344,1.948 2.656,2.146 0.313,0.198 10 false +S 2.792,3.594 3.188,3.865 0.396,0.271 10 false GND 1.125,3.896 1.521,4.167 0.396,0.271 10 false A
*a Component with harness connected
(Combination Meter Assembly)


Check the output waveform.

i.

Remove the combination meter assembly with the connector(s) still connected.


ii.

Connect an oscilloscope to terminal K21-6 (+S) and body ground.


iii.

Turn the power switch on (IG).


iv.

Turn a wheel slowly.


v.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal K21-6 (+S) - Body ground
Tool setting 5 V/DIV., 20 ms./DIV.
Vehicle condition Wheel being rotated

OK:

The waveform is similar to that shown in the illustration.


HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.




Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (NAVIGATION ECU - COMBINATION METER ASSEMBLY)

NG

2.CHECK HARNESS AND CONNECTOR (NAVIGATION ECU - COMBINATION METER ASSEMBLY)
a.

Disconnect the K17 navigation ECU connector.


b.

Disconnect the K21 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K17-9 (SPD) - K21-6 (+S) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR