Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › REAR VIEW MONITOR SYSTEM
RM33C0E _56 Audio / Visual / Telematics _065452 PARK ASSIST / MONITORING _0333741 REAR VIEW MONITOR SYSTEM U

PARK ASSIST / MONITORING  REAR VIEW MONITOR SYSTEM  TERMINALS OF ECU  


REAR TELEVISION CAMERA ASSEMBLY


a.

Disconnect the m2 rear television camera assembly connector.

E292772N27
3.26,0.115 3.854,0.375 0.594,0.26 3.458,0.146 3.771,0.344 0.313,0.198 10 false m2


b.

Measure the voltage of each terminal of the wire harness side connector.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
m2-6 (CB+) - Body ground GR - Body ground Power source Power switch on (ACC) 5.5 to 7.05 V

If the result is not as specified, there may be a malfunction on the wire harness side.


c.

Reconnect the m2 rear television camera assembly connector.


d.

Measure the resistance and check for pulses at each terminal of the connector.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
m2-3 (CV+) - m2-2 (CV-) B - G Video signal Power switch on (IG)
Shift lever in R
Camera lens not covered, displaying an image
Pulse generation
(Refer to waveform 1)
Power switch on (IG)
Shift lever in R
Camera lens covered, blacking out the screen
Pulse generation
(Refer to waveform 2)
m2-5 (CGND) - Body ground BR - Body ground Camera ground Always Below 1 Ω

HINT:

A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the radio and display receiver assembly with the connector connected.


If the result is not as specified, the rear television camera assembly may be malfunctioning.


e.
E265840C01
0.823,2.073 1,2.073 1,2.073 1.125,1.583 false 1.479,2.063 1.344,2.063 1.344,2.063 1.229,1.479 false 0.781,4.167 0.958,4.167 0.958,4.167 1.156,3.594 false 1.521,4.125 1.385,4.125 1.385,4.125 1.271,3.542 false 0.229,0.229 0.542,0.427 0.313,0.198 10 *a 0.396,1.052 0.76,1.313 0.365,0.26 10 GND 0.396,3.208 0.76,3.469 0.365,0.26 10 GND 0.26,2.271 0.625,2.531 0.365,0.26 10 *b 0.646,4.073 1.01,4.333 0.365,0.26 10 *c 0.656,1.979 1.021,2.24 0.365,0.26 10 *c 1.51,1.969 1.875,2.229 0.365,0.26 10 *d 1.542,4.052 1.906,4.313 0.365,0.26 10 *d
*a Waveform 1 (camera lens is not covered, displaying an image)
*b Waveform 2 (camera lens is covered, blacking out the screen)
*c Synchronization Signal
*d Video Waveform


Reference (Oscilloscope waveform):

HINT:

A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the radio and display receiver assembly with the connector connected.


i.

Waveform 1 (camera lens is not covered, displaying an image)

Item Content
Measurement terminal m2-3 (CV+) - m2-2 (CV-)
Measurement setting 200 mV/DIV., 50 μs./DIV.
Condition Power switch on (IG), shift lever in R

HINT:
·

The video waveform changes according to the image sent by the rear television camera assembly.

·

The video waveform is constantly output when the power switch is turned on (ACC).




ii.

Waveform 2 (camera lens is covered, blacking out the screen)

Item Content
Measurement terminal m2-3 (CV+) - m2-2 (CV-)
Measurement setting 200 mV/DIV., 50 μs./DIV.
Condition Power switch on (IG), shift lever in R

HINT:
·

The video waveform changes according to the image sent by the rear television camera assembly.

·

The video waveform is constantly output when the power switch is turned on (ACC).






RADIO AND DISPLAY RECEIVER ASSEMBLY


HINT:

Check from the rear of the connector while it is connected to the components.


E360493N03
0.792,2.323 1.156,2.542 0.365,0.219 5.302,0.417 5.677,0.656 0.375,0.24 3.333,0.427 3.719,0.656 0.385,0.229 1.438,0.406 1.813,0.656 0.375,0.25 2.656,2.344 3,2.594 0.344,0.25 4.385,2.313 4.771,2.573 0.385,0.26 5.833,2.281 6.135,2.5 0.302,0.219 1.531,0.458 1.99,0.656 0.458,0.198 10 false K3 3.427,0.458 3.885,0.656 0.458,0.198 10 false K2 5.406,0.448 5.865,0.646 0.458,0.198 10 false K1 2.75,2.385 3.208,2.583 0.458,0.198 10 false K4 4.417,2.354 4.875,2.552 0.458,0.198 10 false K135 5.885,2.313 6.344,2.51 0.458,0.198 10 false RA 0.927,2.354 1.385,2.552 0.458,0.198 10 false r2

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
K2-26 (CSLD) - Body ground Shield - Body ground Shield ground Always Below 1 V
K2-27 (CGND) - Body ground G - Body ground Camera ground Always Below 1 V
K2-28 (V+) - K3-1 (GND1) B - BR Video signal Power switch on (IG)
Shift lever in R
Camera lens not covered, displaying an image
Pulse generation
(Refer to waveform 1)
Power switch on (IG)
Shift lever in R
Camera lens covered, blacking out screen
Pulse generation
(Refer to waveform 2)
K2-29 (V-) - K3-1 (GND1) W - BR Ground Always Below 1 V
K2-30 (CA+) - K3-1 (GND1) R - BR Rear television camera assembly power supply Power switch on (ACC) 5.5 to 7.05 V

a.

Reference (Oscilloscope waveform):

i.
E265840C01
0.823,2.073 1,2.073 1,2.073 1.125,1.583 false 1.479,2.063 1.344,2.063 1.344,2.063 1.229,1.479 false 0.781,4.167 0.958,4.167 0.958,4.167 1.156,3.594 false 1.521,4.125 1.385,4.125 1.385,4.125 1.271,3.542 false 0.229,0.229 0.542,0.427 0.313,0.198 10 *a 0.396,1.052 0.76,1.313 0.365,0.26 10 GND 0.396,3.208 0.76,3.469 0.365,0.26 10 GND 0.26,2.271 0.625,2.531 0.365,0.26 10 *b 0.646,4.073 1.01,4.333 0.365,0.26 10 *c 0.656,1.979 1.021,2.24 0.365,0.26 10 *c 1.51,1.969 1.875,2.229 0.365,0.26 10 *d 1.542,4.052 1.906,4.313 0.365,0.26 10 *d
*a Waveform 1 (camera lens not covered, displaying an image)
*b Waveform 2 (camera lens covered, blacking out the screen)
*c Synchronization Signal
*d Video Waveform


Waveform 1 (camera lens not covered, displaying an image)

Item Content
Measurement terminal K2-28 (V+) - K3-1 (GND1)
Measurement setting 200 mV/DIV., 50 μs/DIV.
Condition Power switch on (IG), shift lever in R

HINT:
·

The video waveform changes according to the image sent by the rear television camera assembly.

·

The video waveform is constantly output when the power switch is turned to ACC.




ii.

Waveform 2 (camera lens covered, blacking out the screen)

Item Content
Measurement terminal K2-28 (V+) - K3-1 (GND1)
Measurement setting 200 mV/DIV., 50 μs/DIV.
Condition Power switch on (IG), shift lever in R

HINT:
·

The video waveform changes according to the image sent by the rear television camera assembly.

·

The video waveform is constantly output when the power switch is turned to ACC.