Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM
RM33C0E _56 Audio / Visual / Telematics _065452 PARK ASSIST / MONITORING _0333742 BLIND SPOT MONITOR SYSTEM D

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  FREEZE FRAME DATA  


FREEZE FRAME DATA


a.

Whenever DTCs are detected, the blind spot monitor sensor stores the current vehicle (sensor) state as freeze frame data.



CHECK FREEZE FRAME DATA


a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the blind spot monitor system on.


d.

Turn the GTS on.


e.

Enter the following menus: Body Electrical / Blind Spot Monitor Master or Blind Spot Monitor Slave / Trouble Codes.


f.

According to the display on the GTS, read the freeze frame data for the selected DTC.

Body Electrical > Blind Spot Monitor Master
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Main Switch State of the Blind spot monitor system OFF or ON OFF: Blind spot monitor system off
ON: Blind spot monitor system on
-
RCTA Switch Status State of the RCTA function OFF or ON OFF: RCTA function off
ON: RCTA function on
-
Warning Indicator Turning on(Master) State of the outer rear view mirror indicator RH turning on OFF or ON

OFF: Any state except "ON" state

ON: Either of the following state

-

During initial check

-

Blind spot monitor system on, vehicle detected on left hand side and turn signal switch not operated



-
Warning Indicator Flashing(Master) State of the outer rear view mirror indicator RH flashing OFF or ON

OFF: Any state except "ON" state

ON: Either of the following state

-

Blind spot monitor system on, vehicle detected on left hand side and left side of turn signal switch on

-

Vehicle detected by RCTA function



-
Warning Indicator Input Circuit Voltage Outer rear view mirror indicator voltage Min.: 0 V, Max.: 25.5 V Indicator illuminated: 2.5 to 7.5 V
Indicator not illuminated: Below 1 V
-
Warning Indicator Input Circuit Current Outer rear view mirror indicator current Min.: 0 mA, Max.: 255 mA Indicator illuminated: 5 to 100 mA
Indicator not illuminated: 0 mA
-
Turn Switch State State of the turn signal switch Left ON, Right ON or OFF Left ON: Left turn signal switch on
Right ON: Right turn signal switch on
OFF: Turn signal switch off
-
Reverse (Only for AT/CVT) State of the shift position R signal OFF or ON OFF: Shift lever in any position except R
ON: Shift lever in R
-
Vehicle Speed Vehicle speed signal Min.: -327.68 km/h (-204 mph), Max.: 327.67 km/h (204 mph) Vehicle stopped: 0 km/h (0 mph) -
Steering Angle Steering sensor Min.: -3072 deg, Max.: 3070.5 deg Left turn: Increases
Right turn: Decreases
-
Power Supply Voltage Power supply voltage Min.: 0 V, Max.: 49.951 V Power switch on (IG): 11 to 14 V -
Indicator Light Control State Outer rear view mirror indicator dimming state Dim OFF or Dim ON Dim OFF: Indicator not dimmed
Dim ON: Indicator dimmed
-
Angle Adjustment by Auto Alignment Angle adjusted using auto alignment -180 to 180 deg Angle adjusted using auto alignment is displayed -
Yaw Rate Sensor Yaw rate sensor Min.: Under -124.928 deg/s, Max.: 124.684 deg/s Turning right: -125 to 0 deg/s
Turning left: 0 to 124.612 deg/s
-
Number of DTC Number of DTC Min.: 0, Max.: 255 When system is normal: 0
When a malfunction is detected: More than 0
-
Body Electrical > Blind Spot Monitor Slave
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Warning Indicator Turning on(Slave) State of the outer rear view mirror indicator LH turning on OFF or ON

OFF: Any state except "ON" state

ON: Either of the following state

-

During initial check

-

Blind spot monitor system on, vehicle detected on right hand side and turn signal switch not operated



-
Warning Indicator Flashing(Slave) State of the outer rear view mirror indicator LH flashing OFF or ON

OFF: Any state except "ON" state

ON: Either of the following state

-

Blind spot monitor system on, vehicle detected on right hand side and right side of turn signal switch on

-

Vehicle detected by RCTA function



-
Buzzer Sound Status State of the RCTA buzzer (blind spot monitor buzzer) OFF or ON OFF: Buzzer not sounding
ON: Buzzer sounding
-
Warning Indicator Input Circuit Voltage Outer rear view mirror indicator voltage Min.: 0 V, Max.: 25.5 V Indicator illuminated: 2.5 to 7.5 V
Indicator not illuminated: Below 1 V
-
Warning Indicator Input Circuit Current Outer rear view mirror indicator current Min.: 0 mA, Max.: 255 mA Indicator illuminated: 5 to 100 mA
Indicator not illuminated: 0 mA
-
Buzzer Input Circuit Voltage Buzzer Input Circuit Voltage Min.: 0 V, Max.: 25.5 V Engine switch on (IG): 11 to 14 V -
Turn Switch State State of the turn signal switch Left ON, Right ON or OFF Left ON: Left turn signal switch on
Right ON: Right turn signal switch on
OFF: Turn signal switch off
-
Reverse (Only for AT/CVT) State of the shift position R signal OFF or ON OFF: Shift lever in any position except R
ON: Shift lever in R
-
Vehicle Speed Vehicle speed signal Min.: -327.68 km/h (-204 mph), Max.: 327.67 km/h (204 mph) Vehicle stopped: 0 km/h (0 mph) -
Steering Angle Steering sensor Min.: -3072 deg, Max.: 3070.5 deg Left turn: Increases
Right turn: Decreases
-
Power Supply Voltage Power supply voltage Min.: 0 V, Max.: 49.951 V Power switch on (IG): 11 to 14 V -
Indicator Light Control State Outer rear view mirror indicator dimming state Dim OFF or Dim ON Dim OFF: Indicator not dimmed
Dim ON: Indicator dimmed
-
Angle Adjustment by Auto Alignment Angle adjusted using auto alignment -180 to 180 deg Angle adjusted using auto alignment is displayed -
Yaw Rate Sensor Yaw rate sensor Min.: Under -124.928 deg/s, Max.: 124.684 deg/s Turning right: -125 to 0 deg/s
Turning left: 0 to 124.612 deg/s
-
Number of DTC Number of DTC Min.: 0, Max.: 255 When system is normal: 0
When a malfunction is detected: More than 0
-


CLEAR FREEZE FRAME DATA


NOTICE:

Clearing the DTCs will also clear the freeze frame data.


a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the blind spot monitor system on.


d.

Turn the GTS on.


e.

Clear the DTCs and freeze frame data.