Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM
RM33C0E _56 Audio / Visual / Telematics _065452 PARK ASSIST / MONITORING _0333742 BLIND SPOT MONITOR SYSTEM C

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  C1ABE  Short to GND or Open in Buzzer  


DESCRIPTION

DTC C1ABE is stored when the blind spot monitor sensor LH detects a short to ground or open in the RCTA buzzer (blind spot monitor buzzer) circuit.


DTC No. Detection Item DTC Detection Condition Trouble Area
C1ABE Short to GND or Open in Buzzer
Both of the following conditions are met:
·

The blind spot monitor system is on

·

The blind spot monitor sensor is not sounding the buzzer but the buzzer receives voltage below a specified level for a specified period of time.


·

RCTA buzzer (blind spot monitor buzzer)

·

Wire harness or connector



WIRING DIAGRAM

E254403E93
0.167,1.01 1.573,1.208 1.406,0.198 10 false from IG1-NO. 1 Relay 3.5,1 3.792,1.198 0.292,0.198 10 false BZP 3.125,1.302 3.469,1.5 0.344,0.198 10 false R26 3.125,1.479 5.135,1.896 2.01,0.417 10 false RCTA Buzzer (Blind Spot Monitor Buzzer) 5.615,1.927 5.906,2.125 0.292,0.198 10 false W6 5.615,2.083 6.813,2.448 1.198,0.365 10 false Blind Spot Monitor Sensor LH 4.333,1.01 4.667,1.208 0.333,0.198 10 false BZN 3.333,0.906 3.479,1.083 0.146,0.177 10 false 1 5.646,1.021 5.979,1.219 0.333,0.198 10 false BUZ 5.469,0.917 5.615,1.094 0.146,0.177 10 false 3 4.677,0.917 4.823,1.094 0.146,0.177 10 false 2 2.021,1.177 3.198,1.469 1.177,0.292 10 false ECU-IG1 NO.4

CAUTION / NOTICE / HINT

NOTICE:
·

When checking for DTCs, make sure that the blind spot monitor system is turned on.

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.READ VALUE USING GTS (BLIND SPOT MONITOR SENSOR LH STATUS)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Blind Spot Monitor Slave / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Blind Spot Monitor Slave > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Slave Side RCTA Function Switches the RCTA function on and off OFF or ON OFF: RCTA function off
ON: RCTA function on
-
Body Electrical > Blind Spot Monitor Slave > Data List
Tester Display
Slave Side RCTA Function
50003 314 65

Result:
Result Proceed to
"Valid" and "ON" is displayed for all items. A
"Invalid" or "OFF" is displayed. B



A

2.CHECK DTC

B

2.CHECK DTC
a.

Turn the power switch off.


b.

Turn the power switch on (IG).


c.

Recheck for DTCs and check if the same DTC is output again.

Body Electrical > Blind Spot Monitor Slave > Trouble Codes
50001 314
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

NG

3.CHECK HARNESS AND CONNECTOR (RCTA BUZZER - AUXILIARY BATTERY AND BLIND SPOT MONITOR SENSOR LH)
3.CHECK HARNESS AND CONNECTOR (RCTA BUZZER - AUXILIARY BATTERY AND BLIND SPOT MONITOR SENSOR LH)
a.

Disconnect the R26 RCTA buzzer (blind spot monitor buzzer) connector.


b.

Disconnect the W6 blind spot monitor sensor LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R26-2 (BZN) - W6-3 (BUZ) Always Below 1 Ω
R26-2 (BZN) or W6-3 (BUZ) - Body ground Always 10 kΩ or higher



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
R26-1 (BZP) - Body ground Power switch on (IG) 11 to 14 V
R26-1 (BZP) - Body ground Power switch off Below 1 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR