Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM › 2017.09–2018.04
RM33C0E _56 Audio / Visual / Telematics _065452 PARK ASSIST / MONITORING _0333742 BLIND SPOT MONITOR SYSTEM C

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  C1AB2  Short to GND in Outer Mirror Indicator(Master)  


DESCRIPTION

This DTC is stored when the blind spot monitor sensor RH detects a short to ground in the outer rear view mirror indicator RH.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1AB2 Short to GND in Outer Mirror Indicator(Master)
Both of the following conditions are met:
·

The blind spot monitor system is on


·

The current that is sent from the blind spot monitor sensor to the indicator is above a specified level for a specified period of time


·

Outer mirror RH

·

Outer rear view mirror assembly with cover RH

·

Wire harness or connector

·

Blind spot monitor sensor RH



WIRING DIAGRAM

E372912E05
5.958,1.229 6.573,1.427 0.615,0.198 10 false OMIR 2.031,1.135 2.646,1.333 0.615,0.198 10 false BSR+ 2.302,1.646 2.458,1.844 0.156,0.198 10 false - 0.281,2.063 0.896,2.26 0.615,0.198 10 false IND1 0.271,2.219 1.906,2.427 1.635,0.208 10 false Outer Mirror RH 0.188,3.333 0.646,3.531 0.458,0.198 10 false N19 0.167,3.5 7.042,3.698 6.875,0.198 10 false Outer Rear View Mirror Assembly With Cover RH 5.813,3.354 6.125,3.552 0.313,0.198 10 false W5 5.823,3.5 7,4.385 1.177,0.885 10 false Blind Spot Monitor Sensor RH 5.781,1.156 5.938,1.354 0.156,0.198 10 false 4 2.49,1.135 2.646,1.333 0.156,0.198 10 false 3 2.469,1.646 2.781,1.844 0.313,0.198 10 false 11 3.271,1.552 3.583,1.75 0.313,0.198 10 false 12 3.604,1.729 4.104,1.958 0.5,0.229 10 false HTR- 4.427,1.74 4.885,1.938 0.458,0.198 10 false GND 4.917,1.552 5.073,1.75 0.156,0.198 10 false 7 2.927,2.167 5.542,2.438 2.615,0.271 10 false Outer Mirror Control ECU Assembly RH 1.375,1.229 1.531,1.427 0.156,0.198 10 false + 1.396,1.719 1.552,1.917 0.156,0.198 10 false - 1.594,1.146 1.75,1.344 0.156,0.198 10 false 2 1.594,1.625 1.75,1.823 0.156,0.198 10 false 1 0.26,2.385 2.281,2.854 2.021,0.469 10 false (Outer Rear View Mirror Indicator RH) 3.24,1.729 3.74,2.031 0.5,0.302 10 false N10 4.875,1.729 5.125,1.917 0.25,0.188 10 false N9


CAUTION / NOTICE / HINT

NOTICE:

When checking for DTCs, make sure that the blind spot monitor system is turned on.


PROCEDURE

1.CHECK DTC
a.

Turn the power switch off.


b.

Turn the power switch on (IG).


c.

Recheck for DTCs and check if the same DTC is output again.

Body Electrical > Blind Spot Monitor Master > Trouble Codes
50001 313
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH - OUTER REAR VIEW MIRROR ASSEMBLY WITH COVER RH)
2.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH - OUTER REAR VIEW MIRROR ASSEMBLY WITH COVER RH)
a.

Disconnect the W5 blind spot monitor sensor RH connector.


b.

Disconnect the N19 outer rear view mirror assembly with cover RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
W5-4 (OMIR) or N19-3 (BSR+) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY WITH COVER RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY WITH COVER RH
a.

Disconnect the IND1 outer mirror RH connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N19-3 (BSR+) or IND1-2 (+) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT OUTER MIRROR RH

NG

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY WITH COVER RH

4.INSPECT OUTER MIRROR RH

b.

Inspect the outer rear view mirror indicator RH on the outer mirror RH.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR GLASS>INSPECTION


Result:
Proceed to
OK
NG



OK

NG